Insportline IN 162 Denver User manual

1
USER MANUAL – EN
IN 162 Elliptical inSPORTline Denver

2
CONTENTS
SAFETY INSTRUCTIONS.................................................................................................................................... 3
IMPORTANT NOTES ........................................................................................................................................... 3
PARTS LIST........................................................................................................................................................... 4
EXPLODED DRAWING ....................................................................................................................................... 6
CHECK LIST.......................................................................................................................................................... 7
ASSEMBLY INSTRUCTIONS.............................................................................................................................. 8
SM3720 INSTRUCTION MANUAL................................................................................................................... 14
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 17

3
SAFETY INSTRUCTIONS
•To ensure the best safety of the exerciser, regularly check it on damages and worn parts.
•If you pass on this exerciser to another person or if you allow another person to use it, make sure that
that person is familiar with the content and instructions in these instructions.
•Only one person should use the exerciser at a time.
•Before the first use and regularly make sure that all screws, bolts and other joints are properly tightened
and firmly seated.
•Before you start your work-out, remove all sharp-edged objects around the exerciser.
•Only use the exercise for your work-out if it works flawlessly.
•Any broken, worn or defective part must immediately be replaced and/or the exerciser must no longer
be used until it has been properly maintained and repaired.
•Parents and other supervisory persons should be aware of their responsibility, due to situations which
may arise for which the exerciser has not been designed and which may occur due to children’s natural
play instinct and interest in experimenting.
•If you do allow children to use this exerciser, be sure to take into consideration and assess their mental
and physical condition and development, and above all their temperament. Children should use the
exerciser only under adult supervision and be instructed on the correct and proper use of the exerciser.
The exerciser is not a toy.
•Make sure there is sufficient free space around the exerciser when you set it up.
•To avoid possible accidents, do not allow children to approach the exerciser without supervision, since
they may use it in a way for which it is not intended due to their natural play instinct and interest in
experimenting.
•Please note that an improper and excessive work-out may be harmful to your health.
•Please note that levers and other adjustment mechanisms are not projecting into the area of movement
during the work-out.
•When setting up the exerciser, please make sure that the exerciser is standing in a stable way and that
any possible unevenness of the floor is evened out.
•Always wear appropriate clothing and shoes which are suitable for your work-out on the exerciser. The
clothes must be designed in a way so that they will not get caught in any part of the exerciser during the
work-out due to their form (for example, length). Be sure to wear appropriate shoes which are suitable
for the work-out, firmly support the feet and which are provided with a non-slip sole.
•Be sure to consult a physician before you start any exercise program. He may give you proper hints and
advice with respect to the individual intensity of stress for you as well as to your work-out and sensible
eating habits.
IMPORTANT NOTES
•Assemble the exerciser as per assembly instructions and be sure to only use the strucutral parts provided
with the exerciser and designed for it. Prior to the assembly, make sure the contents of the delivery is
complete by referring to the parts list of the assembly and operating instructions.
•Be sure to set up the exerciser in a dry and even place and always protect it from humidity. If you wish
to protect the place particularly against pressure points, contamination, etc., it is recommended to put a
suitable, non-slip mat under the exerciser.

4
•The general rule is that exercisers and training devices are no toys. Therefore, they must only be used by
properly informed or instructed persons.
•Stop your work-out immediately in case of dizziness, nausea, chest pain or any other physical
symptoms. In case of doubt, consult your physician immediately.
•Children, disabled and handicapped persons should use the exercise only under supervision and in
presence of another person who may give support and useful instructions.
•Be sure that your body parts and those of other persons are never close to any moving parts of the
exerciser during its use.
•When adjusting the adjustable parts, make sure they are adjusted properly and note the marked,
maximum adjusting position, for example of the saddle support, respectively.
•Do not work out immediately after meals!
PARTS LIST
Part No. Description Q’ty Part No. Description Q’ty
1 Main frame 1 45 Anti-loose nut 3/8’*26UNF*6.5T 2
2 Front stabilizer 1 46 Handle pulse cable 2
3 Square neck bolt M8*75L 4 47 Plastic plate washer 1
4 Rear foot cap 2 48 Taper washer 2
5L Left front foot cap 1 49 Gasket for chain cover 1
5R Right front foot cap 1 50 Flat washer D20*D11*2T 2
6 Curved washer 12 51 Nylon nut M8 1
7 Spring washer D15.4*D8.2*2T 16 52L Left Handlebar 1
8 Domed nut M8*15L 4 52R Right handlebar 1
9 Bolt M8*20L 10 53 Foam 2
10 Handlebar post 1 54 Foam 2
11 Pedal supporting tube 2 55 Mushroom-head cap 2
12 Movable handlebar support 2 56 Spring 1
13 Bushing D19.15*(D25.6*32) 14 57 Nylon nut M6 4
14L Left cover for pedal 2 58 Screw M6*15L 4
14R Right cover for pedal 2 59 Lower cover for universal axle 2
15 End cap 2 60 Flat washer D23*D117.2*1.5T 1
16 Idle wheel 1 61 Crank axle 1
17 Cover for handlebar 1 62 Magnet 1
18 Nylon nut M10 2 63 Waved washerD17*D22*0.3T 2

5
19 Rear stabilizer 1 64 Computer SM-3720-71 1
20 Square neck screw M6X45L 4 65 Handle plus 2
21L/21R Pedal 1 66 Flat washer D25*D8.5*2T 2
22 Upper cover for universal axle 2 67 Waved washer 2
23 Ladder bolt M10*58L 2 68 C-shape ring D21.5*D17.5*1.2T 8
24 Flat washer D24*D13.5*2.5T 2 69 Front pedal axle 2
25 Screw ST4.2*1.4*15L 2 70 Fixing plate for idle wheel 1
26 C-shape ring S-17(1T) 2 71 Swing Axle D19*374.5 1
27 Electric cable 1 72 Fixed handlebar 1
28 Sensor cable 1 73 Flat washer D14*D6.5*0.8T 4
29 Upper computer cable 1 74 Anti-loose nut 2
30 Lower computer cable 1 75 Screw ST4*20 4
31 Bushing D29*D11.9*9T 4 76 Upper cover 1
32 Universal joint 2 77 Knob 4
33 Crank 2 78 Adaptor 1
34 Belt wheel 1 79 Bushing 1
35 Belt 1 80 Hex head bolt 1
36L Left chain cover 1 81 Flat washer 1
36R Right chain cover 1 82 Nut 1
37 Magnetic system 1 83 Inner plug 1
38 Bolt cap M8 2 84 Motor 1
39 Side cover 2 85 Cross screw 8
40 Bolt M8*25L 2 86 Screw 9
41 Nylon nut 1 87 Screw 2
42 Round cover 2 88 Screw 1
43 Bearing 2 89 Chest belt 1
44 Flat washer D22*D11*2T 1 90 Tension cable 1

6
EXPLODED DRAWING
40
66
38
71
13
53
52R
3
19
4
13
68
11
8
7
6
9
7
48
38
40
66 13
67
65
49
5L
5R
10
6
7
9
64
69
67
68 13
68
14L
54
15
72
36L
36R
42
39
2
45
44
52L
7
9
6
12
7
7
43
33
74
61
60
63
26
33
35
58
57
34
62
1
69
67
68 13
68
13
68
13
67
68
59
18
50
22
23
24
31
32
50
18
24
23
31
42
14R
9
7
6
14L
14R
13
12
21R 75
75
76
29
30
78
25
28
27
20
73
77
37
55
79
83
17
9
7
6
16
41
56
51
80
81
82
47
70
84
85
86 87
46
88
89
90

7
CHECK LIST
1
X 1
10
21L&R
71
2
19
64 17
72
M8*1.25*75L D22*D8.5*1.5T D15.4*D8.2*2T
M8*1.25*15L
M8*1.25*20L
D14*D6.5*0.8T
367
9820
73
D25*D8.5*2T
66
M8*1.25*25L
40
38 67
22&59
ST4*20L
75
78
M6*1*45L
77
X 1
X 1
X 1
X 1
X 1
X 1
X 4
X 1
X 1
X 1
X 1
X 2
X 2
X 4
X 10
X 2
X 2
X 4
X 12
X 16
X 4
X 4
X 4
X 2
X 1
52L&R
X 1
D14*D8*4T
48
X 2
X 1
89

8
ASSEMBLY INSTRUCTIONS
STEP 1:
Assemble the front stabilizer (2) and rear stabilizer (19) onto the main frame (1) by using the two square
neck bolts (3), the two curved washers (6), then two spring washers (7) and two domed nuts (8) separately.

9
STEP 2:
First connect the upper computer cable (29) with the lower computer cable (30).

10
STEP 3:
Insert the swing axle (71) through the movable handlebar support (12), assemble one waved washer (67)
every side, and the movable handlebar support (12), then assemble one flat washer (66), one spring
washer (7) every side, then tighten with the bolt (40), last cover the screw cap (38).