jbc MSE-A User manual

MSE
Electric Desoldering Module
for DDU & DMU
INSTRUCTION MANUAL

Electric Desoldering
Module .............................1 unit
Paper Filters ...................1 unit
Ref. 0005966
Ref. contains 50 filters
Suction Filter ..................1 unit
Ref. 0821830
Module Cable
connector ........................1 unit
Ref. 0024228
Cotton Filter .................. 1 unit
Ref. 0781046
Ref. contains 10 filters
Manual .............................1 unit
Ref. 0027988
Packing List
The following items are included:
This manual corresponds to the following reference:
MSE-A
2

to Another Peripheral
to
Control Unit
to
Tool
to Pedal
Suction Filter
Features and Connections
Compatibility
Select the equipment that best suit your soldering or desoldering needs.
Module Stand Tool Cartridge
Range
Control Units Peripherals
DDU DMU P005
MSE
DSS DS360 C360
DRS DR560 C560
Control Unit
“switch on” Indicator
In Use Indicator
Desoldering Air Filter
3
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm

MENU
17:14 ?
Install
MODULE
Air pump
Postpone
Initial Set up
For DDU Control Unit
When a new module is detected, a pop-up
screen appears and proceed as indicated.
If no screen is shown, click on the icon
on the main bar and follow the steps.
Once set up, you can change the module
settings by entering the Peripherals Menu.
For DMU Control Unit
Appears only when the
installation is postponed
Peripherals Port 2-DR
17:14
Pedal None
Module None
Module
MSE_a
None
1. Select the module from the list of peripheral
connections. Remember your first connection
is denoted as “a”, the second being “b”, etc.
(e.g. MSE_a, MSE_b,...)
2. Press Menu or Back to save changes.
Once set up, you can change the module
settings by entering the Peripherals Menu.
Peripherals
After connecting the module, enter the Peripherals Menu and select the port which
you want to join with the module.
4

Maintenance
Paper Filters
Ref. 0005966
Cotton Filters
Ref. 0781046
Suction Filter
Ref. 0821830
O Ring
Ref. 0007717
Filter Cover
Ref. 0004710
Important: Do not use sharp pointed objects to open the suction filter.
Before carrying out maintenance or storage, always unplug the equipment.
- Keep the casing clean by using a damp cloth. Specially use a soft cloth for the front side.
- Periodically check all cable and tube connections.
- Keep filters clean to ensure proper solder suction and replace them when necessary.
- Use original JBC spare parts only.
- Do not work with defective or damaged pieces.
- Repairs should only be performed by a JBC authorized technical service.
- Maintenance must not be carried out by children unless supervised.
5
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm

Safety
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the
station is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
6

Notes
7
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
MSE
Electric Desoldering Module for DDU & DMU
Ref.: MSE-A
- Net Weight: 1.22 kg / 2.69 lb
- Module Dimension (L x W x H): 225 x 145 x 55 mm / 8.86 x 5.71 x 2.17 x in
- Vacuum: 75% / 570 mmHg / 22.4 inHg
- Flow rate: 9 SLPM
- Ambient Operating Temperature: 10 - 40 ºC / 50 - 104 ºF
- Pedal Connection
- Total Package Dimensions / Weight: 280 x 195 x 115 mm / 1.53kg
(L x W x H) 11.02 x 7.68 x 4.53 in / 3.36 lb
Complies with CE standards.
ESD protected.
Specifications
0027988-0921