jbc MVE-A User manual

Pneumatic Desoldering Module
Ref. MVE-A
www.jbctools.com

Packing List
The following items should be included:
Pneumatic Desoldering
Module .............................1 unit
Ref. MVE-A
Filter Box ........................ 1 unit
Ref. 0005966
It contains 50 filters
Suction Filter ..................1 unit
Ref. 0821830
Module Cable
connector ........................1 unit
R ef. 0 014 874
Cotton Filter ...............10 units
Ref. 0781046
Manual .............................1 unit
Ref. 0017955
Pneumatic Desoldering Module
Ref. MVE-A
Escape Filter ..................1 unit
Ref. 0008446
2
www.jbctools.com

Air pressure
(4-6 bar)
Tubing Ø4 x Ø6 mm
(Not supplied)
Compatibility
Select the equipment that best suit your soldering or desoldering needs.
Module Stand Tool Cartridge
Range
Control Units Peripherals
DDE DME P-005
MVE-A
DS-SD DS360-A C360
DR-SD DR560-A C560
Pneumatic Desoldering Module
Ref. MVE-A
to Another peripheral
to
Control Unit
to
Tool
to Pedal
Suction Filter
Features
www.jbctools.com
3

MENU
17:14 ?
Install
MODULE
Air pump
Postpone
Peripherals Port 2-DR
17:14
Pedal None
Module None
Module
MVE_a
None
Initial Set up
For DDE Control Unit
When a new module is detected, a pop-up
screen appears and proceed as indicated.
If no screen is shown, click on the icon
on the main bar and follow the steps.
Once set up, you can change the module
settings by entering the Peripherals Menu.
For DME Control Unit
Appears only when the
installation is postponed
1. Select the module from the list of peripheral
connections. Remember your first connection
is denoted as “a”, the second being “b”, etc.
(e.g. MVE_a, MVE_b,...)
2. Press Menu or Back to save changes.
Once set up, you can change the module
settings by entering the Peripherals Menu.
Peripherals
After connecting the module, enter the Peripherals Menu and select the port which
you want to join with the module.
4

Maintenance
Spare filters
Ref. 0005966
Cotton filters
Ref. 0781046
Suction filter
Ref. 0821830
O Ring
Ref. 0007717
Filter cover
Ref. 0004710
Important: Do not use sharp pointed objects to open the suction filter.
Before carrying out maintenance, always unplug the electric and pneumatic connectors.
- Use a damp cloth to keep the casing clean.
- Periodically check all cable and tube connections.
- Keep filters clean to ensure proper solder suction and replace them when necessary.
Escape filter
Ref. 0008446
- Use original JBC spare parts on
- Do not work with defective or damaged pieces.
- Repairs should only be performed by a JBC authorized technical service.
- Maintenance must not be carried out by children unless supervised.
Removing the pneumatic tubing
1
2
Push the release ring to remove
the pneumatic tubing. Release ring
www.jbctools.com
5

It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Make sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight as well as persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Safety
6

Exploded View
www.jbctools.com
7

This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Manual in other languages available on our website
Warranty
JBC’s two year warranty covers this equipment
against all manufacturing defects, including
the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased. Please register your
product warranty within 30 days of purchase in:
www.jbctools.com/productregistration.
www.jbctools.com
-Weight: 700 gr (1.54 lb)
- Dimensions: 145 x 55 x 225 mm (5.71 x 2.17 x 8.86 in)
- Air Pressure supply range: 4 - 6 Bar
- Vacuum at 6 Bar: 90% / 680 mmHg / 26.8 inHg
- Flow rate: 15 SLPM
- Ambient operating temp.: 10 - 40 ºC (50 - 104 ºF)
- Pedal connection
Complies with CE standards.
ESD protected.
Specifications
0017955-0318