jbc UCR470-5A User manual

Control Unit for Robot
Ref. UCR470-5A
www.jbctools.com

2

Packing List
The following items should be included:
There are up to 44 functions to control the station, such as:
- Temperature control
- Sleep and Hibernation control
- Station status
- Error Information
- Counters (working time, sleep, hibernation... )
Manual ............................ 1 unit
Ref. 0020996
Tool Cable ...................... 1 unit
Ref. 0 021403
Communications
Cable ............................... 1 unit
Ref. 0020261
Control Unit
for Robot ........................ 1 unit
Ref. UCR470-5A
Power Cord .................... 1 unit
Ref. 0009401
Ref. UCR470-5A
Control Unit for Robot
Functions
www.jbctools.com
3
www.jbctools.com

*LED Indicator
Blue: Equipment powered.
Green: Equipment working.
Red: Error.
Errors
In case of error, a red light flashes a certain number of times, indicating an error number as shown in
the table below:
If the error persists, contact with JBC technical service.
Features
Fuse
Equipotencial
Connector
Power Socket
Main Switch
Tool Connector Communications Connector
LED Indicator*
Nº Error Description Solution
1 times Shortcircuit Replace cartridge
2 times Open circuit Replace cartridge
3 times Not accepted tool Check if the tool is compatible with the station
4 times Tool detection error Check the tool
6 times Current usage leads to overloading Due to overload wait until the device has cooled down
7 times Shortcircuit Check if the cartridge is compatible with the station
12 times Memory error Reset the station
4

1 3
5
2 4
Transmitted data - Grey cable
Optional:
Pedal activation by
relay or digital output
Ground - Blue cable
Brown cable
Black cable
Front view
Received data - White cable
Male DB9
Connector
5
4
9
8
7
6
3
2
1
Connection
- The UCR470-5A control unit for robot can be connected to a PLC by a five-pin communications
cable connector (Ref. 0020261).
- For a proper connection, it is only necessary to connect three of the five pins to a typical DB9 male
connector (PLC or computer).
Communications connector
Pin Color Description
1 Brown Not used
2 White Serial input: RS232 RX
3 Blue Common reference:
GND for RS232 and pedal
4 Black Pedal input: OV or 24V to start feeding.
Leave it open to stop
5 Grey Serial output: RS232 TX
Communications Cable
Ref. 0020261
- See the following communications connector pin distribution:
Robot Communication Protocol available in www.jbctools.com
www.jbctools.com
5

Dimensions
Dimensions in mm
(Dimensions in in)
6

Compatibility
The Control Unit for Robot UCR470-5A works with TR470-A and TRA470-A devices and its cartridge
range R470. Connect any of those tools with the provided cable (Ref. 0021403).
Find more information in www.jbctools.com
Ref. TR470-A Ref. TRA470-A
Maintenance
- Before carrying out maintenance, always allow the equipment to cool down.
- Periodically check all cables and tube connections.
- Replace a blown fuse as follows:
1. Pull off the fuse holder and remove the fuse.
If necessary use a flat screwdriver to lever it off.
2. Insert the new fuse into the fuse holder and
return it to the station.
- Replace any defective or damaged pieces. Only use original JBC spare parts.
- Repairs should only be performed by a JBC authorized technical service.
Fuse
www.jbctools.com
7

It is imperative to follow safety guidelines to prevent electric shock,
injury, fire or explosion.
- Do not use the unit for any purpose other than soldering or rework. Incorrect use may cause fire.
- The main cable must be plugged into approved bases. Make sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Heat can cause inflamable products to ignite even when not visible.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight as well as persons with reduced
physical, sensory or mental capabilities or lacking experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Safety
8

产品中有害物质的名称及含量
有害物质含量表
部件名称
有害物质
铅(Pb) 汞(Hg) 镉(Cd) 六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
烙铁头 O O O O O O
手柄 O O O O O O
电源线 O O O O O O
主机 O O O O O O
电源插座 O O O O O O
保险丝 O O O O O O
主开关 O O O O O O
电位连接 X O O O O O
变压器 O O O O O O
线路板 X O O O O O
O 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572 规定的限量要求以下。
X 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求。
www.jbctools.com
9

Notes
10

www.jbctools.com
11

This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Manual in other languages available on our website
Warranty
JBC’s two year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour. Warranty
does not cover product wear or misuse. In order for
the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased.
Register your warranty within 30 days of purchase
in www.jbctools.com/productregistration
00209 96 -0318
Specifications
UCR470-5A 85 - 265V 50/60Hz. Input fuse: 4A. Output: 42V.
- Weight: 2,2 kg (4.9 lb)
- Dimensions: 210 x 162 x 75 mm (8.3 x 6.4 x 3.0 in)
- Output Peak Power: 250W
- Temperature Range: 90 - 500 °C (190 - 932 °F)
- Idle Temp. Stability (still air): ±1.5 ºC / ±3 ºF
- Tip to ground resistance: < 2 ohms
- Tip to ground voltage: < 2mV RMS
- Ambient operating temp: 10 - 40 ºC (50 - 104 ºF)
- Connections: M8-5pins for Robot
Complies with CE standards.
ESD protected housing.
www.jbctools.com