JCROffroad BR6RK-HT Configuration guide

6TH GEN BRONCO
4 DOOR SHORT RACK..........................2
6TH GEN BRONCO
2 DOOR SHORT RACK..........................9
TABLE OF CONTENTS

6TH GEN BRONCO
4 DOOR HARD TOP
SHORT RACK
INSTALL INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.
Thank you for purchasing from JcrOroad! Checkout our website, www.jcroroad.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-353-1184!

INCLUDED HARDWARE
20x
8x
20x
1/4” ID
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head

INCLUDED PARTS
2x 3x 1L/1R
1L/1R
1L/1R
1L/1R

1Start by mounting three crossbars between the side rails. For this, use the
1/4”-20 X 3/4” button head bolts and the 1/4” ID washers (2 per bar per
side). Make sure the machined slot in the rail of the crossbar is facing up so
you can easily add t-nuts to mount your gear.
ASSEMBLY

ASSEMBLY
2Next, find the inner mounts labeled M and R. The inner mounts are the
ones with the sharper angles. Apply one of the provided rubber sheets to
the bottom of each of them, making sure that the rubber hugs the bracket
tightly across the entire bottom. For visual aid on this step, check out 1:55
in the instruction video at the bottom of the rack’s product page.
3Once the rubber is on each mount, loosely attach them to the inside of
the side rails using the 1/4”-20 X 3/4” button head bolts, 1/4” ID washers
and 1/4”-20 serr. flange nuts. The mounts labeled R go towards the rear
(the flatter side) and the mounts labeled M go towards the front. Each
mount should have an arrow pointing towards the front. With the mounts
in place, set the rack on the hard top with each mount sitting flat in the
indentations on the hard top.

ASSEMBLY
4Next, find the outer R and M mounts and apply the remaining rubber
sheets the bottom of each, similar to the inner mounts. Be sure to cover
the top of the hook flange as well. For visual aid on this step, check out
5:20 in the instruction video at the bottom of the rack’s product page.
5Once the rubber is in place, remove the hardware holding the inner mounts
in place and loosely install the outer mounts using that hardware. They
mount to the outside of the side rails through the same holes as the inner
mounts and the bottom hook flange slides into the cutouts in the side of
the hardtop above the windows. It is easiest to do this one at a time with
a rag under the corner of the rack that isn’t being supported by a mount.
That way there is no risk of the rack scratching the roof surface. The
mounts labeled R go together and the mounts labeled M go together. The
arrows should be pointing towards the front. Once everything is loosely
in place, go back and tighten all the hardware while making sure that the
inner mounts are pushed down tight to the surface of the roof.

DIMENSIONS

6TH GEN BRONCO
2 DOOR HARD TOP
SHORT RACK
INSTALL INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.
Thank you for purchasing from JcrOroad! Checkout our website, www.jcroroad.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-353-1184!

INCLUDED HARDWARE
24x
8x
24x
1/4” ID
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head

INCLUDED PARTS
2x 4x 1L/1R
1L/1R
1L/1R
1L/1R

1Start by mounting four crossbars between the side rails. For this, use the
1/4”-20 X 3/4” button head bolts and the 1/4” ID washers (2 per bar per
side). Make sure the machined slot in the rail of the crossbar is facing up so
you can easily add t-nuts to mount your gear.
ASSEMBLY

ASSEMBLY
2Next, find the inner mounts labeled R and M. The inner mounts are the
ones with the sharper angles. Apply one of the provided rubber sheets to
the bottom of each of them, making sure that the rubber hugs the bracket
tightly across the entire bottom. For visual aid on this step, check out
1:55 (R) and 19:20 (M) in the instruction video at the bottom of the rack’s
product page.
3Once the rubber is on each mount, loosely attach them to the inside of
the side rails using the 1/4”-20 X 3/4” button head bolts, 1/4” ID washers
and 1/4”-20 serr. flange nuts. The R mounts go towards the rear. Each
mount should have an arrow pointing towards the front. With the mounts
in place, set the rack on the hard top with each R mount sitting flat in the
indentations on the hard top.

ASSEMBLY
4Next, find the outer R mounts and attach more of the rubber sheets the
bottom of each, similar to the inner mounts. Be sure to cover the top of
the hook portion as well. For visual aid on this step, check out 5:20 in the
instruction video at the bottom of the rack’s product page.
5Once the rubber is in place, remove the hardware holding the inner
R mounts in place and loosely install the outer R mounts using that
hardware. They mount to the outside of the side rails through the same
holes as the inner mounts and the bottom hook flange slides into the
cutouts in the side of the hardtop above the windows. The arrows should
be pointing towards the front. Once everything is loosely in place, tighten
them fully while making sure that the inner mounts are pushed down tight
to the surface of the roof.

ASSEMBLY
15 Finally, with the rack secured into position, find the outer M mounts and
attach the remaining rubber sheets the bottom of each. On these mounts,
do not cover the hooked portion with the rubber because it will not fit
into position if you do so. For visual aid on this step, check out 18:50 in the
instruction video at the bottom of the rack’s product page. You can then
bolt them onto the rack using the hardware that is holding the inner M
mounts in place. Make sure to slip the hooked portion of the mounts into
the small slot in the hardtop, similar to the way the R mounts install, except
without the extra cutout to locate it. The arrows should point towards the
front of the vehicle.

DIMENSIONS