JCROffroad BR6RMP Configuration guide

4 DOOR 6TH GEN BRONCO REAR
WINDOW MOLLE PANEL.....................2
2 DOOR 6TH GEN BRONCO REAR
WINDOW MOLLE PANEL.....................7
TABLE OF CONTENTS

Thank you for purchasing from JcrOroad! Checkout our website, www.jcroroad.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-353-1184!
Please read the mounting instructions below carefully before attempting to install.
Be sure to check out the install video on the product page, if available.
4 DOOR 6TH GEN BRONCO
REAR WINDOW
MOLLE PANEL
INSTALL INSTRUCTIONS

INCLUDED HARDWARE
4x
4x
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head 3x 25mm M8 Button Head

INCLUDED PARTS
1x
1x
1x 1x
1x
HARD TOP ONLY SOFT TOP ONLY

1Start by popping the small plastic panel beneath the rear window out of
place. Then, detach the nearest seat belt from its mounting point. To do
this, pop the plastic cover o of it by pulling out on the top edge of it.
Doing this will expose a bolt. Unscrew that bolt using a T50 socket and
then you will need to thread the push nut o of the back of the bolt in
order to get the spacer o. Set everything to the side for now, making sure
not to lose any hardware.
ASSEMBLY
2Next, loosely attach the mounts to the vehicle. The rear mount attaches
directly to the rear roll bar using an M8 bolt through a factory threaded
hole as shown below on the le. The lower mounts are slightly dierent
depending on whether you have a so top or hard top. The hard top
mount attaches behind the plastic panel you pulled o using two more
M8 bolts in threaded factory holes as shown below on the right. The so
top mount needs to be installed into the top two so top mounting holes
using the factory hardware. These holes are located behind the plastic
panel as well you removed as well. The front mount gets sandwiched
between the seatbelt retainer and the spacer you removed. Place the wider
slot onto the bolt behind the retainer, and then reinstall the spacer and
push nut. Then, reinstall the whole thing back into the seat belt’s factory
mount. Make sure that all the mounting faces for the MOLLE panel are
pointing out, away from the window.

3Next, loosely mount the panel to the mounts using the four 1/4”-20 X 3/4”
button head bolts and 1/4”-20 serr. flange nuts. Once all bolts are loosely
in place, adjust the position of the panel in the window until you are happy
with it. Then, tighten everything into place, starting with the bolts holding
the upper two mounts to the frame, followed by the lower mount. Finally,
tighten the bolts holding the panel to the mounts. When tightening the
seatbelt back into place, torque it to 40  lbs.
ASSEMBLY

Thank you for purchasing from JcrOroad! Checkout our website, www.jcroroad.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-353-1184!
Please read the mounting instructions below carefully before attempting to install.
Be sure to check out the install video on the product page, if available.
2 DOOR 6TH GEN BRONCO
REAR WINDOW
MOLLE PANEL
INSTALL INSTRUCTIONS

INCLUDED HARDWARE
6x
6x
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head 3x 25mm M8 Button Head

INCLUDED PARTS
1x
1x 3x
1x

1Start by loosely installing all the mounts to the inside of the rear window.
The three small L shaped brackets get installed into the hardtop mounting
points on the bottom of the window using the factory hardware. The
longer leg of the bracket is the one that gets mounted to the vehicle. The
shorter leg should be pointing up and positioned towards the inside of the
mounting bolts. The flat bracket installs into the middle of the outside face
of the roll cage through two factory holes using the provided M8 button
heads. The larger L shaped bracket mounts to the top of the face of the roll
cage, in front of the flat bracket.
ASSEMBLY

2Once all the mounts are loosely installed, mount the MOLLE panel to them
using the 1/4”-20 X 3/4” button head bolts and 1/4”-20 serr. flange nuts.
Once the panel is loosely installed, tighten the mounts into place. Then,
adjust the position of the panel until it is where you want it and then
tighten it into place.
ASSEMBLY