JCROffroad OGFL-BR6G User manual

Thank you for purchasing from Victory 4x4! Checkout our website, jcroroad.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-353-1184!
INSTALL INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Be sure to check out the install video on the product page, if available.
OFF-GRID FLOOR
SYSTEM
4 DOOR 6TH GEN BRONCO

INCLUDED HARDWARE
1/4” Black
Washer
48x 1/4”-20 x 1/2”
Button Head
50x
1/4” Flange Nuts
22x 6mm x 25mm
Button Head
2x

INCLUDED PARTS
2x
1x
2x
2x
4x

1. Start by assembling the (2) provided side brackets to the (2) front bracket
using the 1/4” bolts, washers and flange nuts. Be sure to assemble in the
correct orientation as shown below, with the cut outs in the side brackets
pointing toward the middle. Be sure to do this process on both sides and
ends.
ASSEMBLY

2. Once the (2) side brackets are assembled and tight to the front, you’re
going to install the (4) provided corner support brackets. These install
using the provided 1/4” button heads, washers and flange nuts. Be sure
to assemble in the correct orientation as shown below, with the back
flange going on the inside of the front bracket and the inside flange on the
outside of the side brackets.
ASSEMBLY

ASSEMBLY
3. With the (4) outside brackets assembled and tight with the corner
supports, you can install the provided middle bracket using the 1/4” button
heads, washers and flange nuts. This will install pretty much the same as
the side brackets to the front and back brackets. Be sure to install in the
orientation below with those teardrop cut outs at the top pointing out and
down toward the middle. Be sure to do this on both ends of the bracket.

ASSEMBLY

4. Now that the frame of the floor is assembled and tight, you now need
to do some disassembly on the inside of your Bronco. There will be (4)
plastic covers over each of the factory tie down hooks that will need to be
removed. Once all (4) covers are removed, you will need a 10mm socket to
remove the (2) bolts holding each of the hooks down. Once all of the bolts
are removed, you can then simply remove all (4) hook assemblies. Once the
hooks are out of the way you can remove the floor as a whole.
ASSEMBLY

5. With the factory floor now out of the way, you can grab the frame you
assembled and place it in the back of the Bronco. Be sure to make sure
that the teardrop cut outs in the middle bracket are away from you, going
in toward the front of the vehicle. You may have to insert the frame at an
angle to get it to fit into the back. Once it is in the vehicle, lay it flat and
push forward and down and it should kind of snap into place between the
plastics.
ASSEMBLY

6. Now that the frame is in place, take the factory bolts that were removed to
hold down the factroy hooks and use them in the same locations to secure
the frame to the floor. Using a 10mm socket secure the bolts through the
corner support brackets into the factory threaded holes.
ASSEMBLY

7. Once the frame is bolted in place, you can grab one of your two floor
panels and begin to install it to the frame. Any accessories you plan on
installing to the floor panels need to be bolted in place before assembling
to the frame. You will be provided with bolt in nut tabs, and the orientation
of these depend on the accessory that you’re installing. For more details
check out our product pages and install videos on fridge slides and drawer
assemblies. But for this install we will be just showing you how to bolt the
floor panels to the frame. It doesn’t matter which side each panel goes
on, just make sure the end of the panel with the teardrop cut outs on it is
closest to you. Once you have the panel laid on top of the frame, start to
line up the holes in the panel to the mounting holes with the pems in the
frame. Once the holes are lined up, use the provided 1/4” button heads to
secure them. Be sure to do this process on both sides.
ASSEMBLY

8. Once both sides are tight, you are finsihed with your floor install. For
placement and specific instruction of your new drawer or fridge slide, refer
to your vehicle floor product page on our website for more details.
ASSEMBLY
This installation guide shows how to assemble one floor system, but the
possibilities are endless! Check out the product page for inspiration on how
to maximize your space by using a combination of O-Grid Drawers and
our O-Grid Fridge Slide!