John Lewis HERRINGBONE IP44 WALL LIGHT User manual

HERRINGBONE GLASS OUTDOOR
IP44 WALL LIGHT
USER GUIDE

01
Description Image QuantityParts list
Introduction Thank you for purchasing this Herringbone
IP44 wall light. Please read the instructions
carefully before use to ensure safe and
satisfactory operation of this product.
Warnings We recommend a qualified electrician carries out any electrical wiring outdoor.
For your safety, this product must be installed in accordance with local Building
Regulations.
If in any doubt, or where required by the law, consult a competent person who is
registered with an electrical self-certification scheme. Further information is available
online or phone your Local Authority.
To prevent electric shock, switch off the mains supply before installing or maintaining
this product. Ensure other persons cannot restore the electricity supply without your
knowledge.
Always use the correct bulb type with the correct wattage as indicated in the
specification table. This product is Class I = and should be fitted to a lighting
supply (with earth) protected by a 5 amp fuse or equivalent circuit breaker.
When changing the bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
If the inner glass on this product is broken, it must be replaced
A
C
D
Wall Light
Inner glass shade
Fixing bracket
Fixing screw pack
1
1
2
1
B
2
1
E
F
Outer shade
Shade cover

02
Product assembly
1
3
2Lever open the terminal block box cover with a small
screwdriver, pierce a hole in the black rubber seal of the
terminal block and make sure this creates a tight seal then
feed supply cable through.
Make electrical connections as follows:
Fit the bulb, type and wattage as indicated on the fitting (bulb
not supplied). The wattage indicated must not be exceeded.
To fit the shade (D): Offer the shade glass over the lamp
holder section, align the treads and carefully screw into place.
If cross-threading occurs, undo and start again. Take care not
to over-tighten as this may cause damage to the the glass or
the fitting.
Remove mounting bracket (A) from fitting by removing
there retaining screws and washers, retain for later. Using
the mounting bracket as a template, mark and then drill
the fixing holes in the wall (ensure the screws (B) are
firmly fixed into a solid or other suitable mounting and
not just the plasterboard.). Take care not to damage
wiring. Attach mounting bracket to the mounting surface
using suitable fixings. Do not attach fitting to mounting
bracket at this stage. Make sure no wires are trapped in
the process.
- Connect supply live to fitting live (marked “L”) on the
terminal block.
- Connect supply neutral to fitting neutral (marked “N”) on
the terminal block.
- Connect the supply earth to the earth (marked “ ”) on
the terminal block.
NOTE: Ensure electrical connections are tight and no loose
strands of wire are left out of the connector block. Ensure
terminals and rubber seal are correctly seated then close
connector block housing. Excess cable must be carefully
located inside the wall plate or within the wall cavity itself.
Carefully offer fitting (C) over mounting bracket then
secure in place with the screws and washers removed
earlier.
B
B
D
D
A
A
C
C

03
Product assembly
4
5Fit the upper and lower metal shade covers (F) by
aligning the holes in the cover plates with those in the
shade and the light fitting. Insert and tighten the retaining
screws using a correctly sized screwdriver. Ensure all
assembled parts have been fully secured before leaving
unattended.
Once installation is complete, the house
electricity may be restored at the fuse box.
Place the outer shade glass (E) over the light fitting
and alignin the fixing holes on both parts.
E
E
F
F
F

04

05

06

John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China Please retain these instructions for future reference.
5 year guarantee
If you experience any unresolvable technical issues with the product, contact
your nearest John Lewis & Partners shop or John Lewis & Partner Technical
Support on 03301 230106.
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
Aftercare and
Troubleshooting
Max. power: 5W LED Only (500-700 lumen)
Voltage: 220–240V, 50Hz IP rating: 44
Weight: 2.3kg
At John Lewis & Partners we test every light to high quality standards so we are
able to offer you a 5 year guarantee.
Specification
Recycling
Caring for
your product
We recommend cleaning with a soft dry cloth. Do not use abrasive materials
as these will damage the finish.
Replace bulb from John Lewis or established brand of the same type and
compatibility.
This symbol indicates that this product should not be treated as normal
household waste and it should be recycled. John Lewis & Partners do not
operate instore take back, but as members of the Distributor Take Back
scheme have funded the development and upgrade of recycling facilities across
the UK. Please take it to your nearest collection facility or for further details
contact your local council or visit www.recycle-more.co.uk.
IL4328 Issue 1 09/20