JUMO AQUIS touch P User manual

20258007T92Z001K000
V3.00/EN/00661195
JUMO AQUIS touch P
Modular Multichannel Measuring Device for Liquid
Analysis with Integrated Controller and Paperless
Recorder
Interface description
PROFINET IO

Contents
Contents
1 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Warning symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Note signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Compatibility and system requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 PROFINET IO and Ethernet standard services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Requirements for hardware, software, and cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 The GSDML file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Module description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.1 Introduction to the module concept. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.2 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Noncyclical data exchange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Programming the noncyclical data exchange in the IO controller. . . . . . . . . . . . . . . . . . . . . . . 17
5.1.1 Single-ID and Multi-ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Data tables of noncyclical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2.1 Configuration data and parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2.2 Process values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6 Project planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.1 Project integration of JUMO IO devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2 Configuring PROFINET modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.3 Configuring the JUMO IO device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.3.1 Start-up parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.3.2 Communication parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.3.3 Device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.1 Error messages for invalid values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8 Annex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8.1 PROFINET certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Contents

5
1 Safety information
1 Safety informat ion
1.1 Warning symbols
DANGER!
This symbol indicates that personal injury caused by electrical shock may occur if the respective pre-
cautionary measures are not carried out.
WARNING!
This symbol in connection with the signal word indicates that personal injury may occur if the respective
precautionary measures are not carried out.
CAUTION!
This symbol in connection with the signal word indicates that material damage or data loss will occur
if the respective precautionary measures are not taken.
CAUTION!
This symbol indicates that components could be destroyed by electrostatic discharge (ESD = Electro
Static Discharge) if the respective cautionary measures are not taken.
Only use the ESD packages intended for this purpose to return device inserts, assembly groups, or as-
sembly components.
1.2 Note signs
NOTE!
This symbol refers to important information about the product, its handling, or additional use.
READ THE DOCUMENTATION!
This symbol, which is attached to the device, indicates that the associated documentation for the de-
vice must be observed. This is necessary to identify the nature of the potential hazard, and to take
measures to prevent it.
REFERENCE!
This symbol refers to additional information in other sections, chapters, or other manuals.
FURTHER INFORMATION!
This symbol is used in tables and indicates that further information is provided after the table.
&
DISPOSAL!
At the end of its service life, the device and any batteries present do not belong in the trash! Please en-
sure that they are disposed of properly and in an environmentally friendly manner.

1 Safety information
6

7
2 Compatibility and system requirements
2 Compatibility and system requirements
2.1 Certification
JUMO IO devices are certified by the PNO to Conformance Class B (abbreviated to CC-B) and net load
class "Netload Class III".
2.2 PROFINET IO and Ethernet standard services
The PROFINET interface supports all Ethernet standard services. Over this interface, the device can
also be accessed via the JUMO PC setup program and the JUMP PCC/PCA software. Additionally, the
JUMO field device can send its e-mails over this interface. The Ethernet standard services are also avail-
able during the cyclical PROFINET communication.
The PROFINET IO communication occurs in a parameterizable time pattern (RT channel). This ensures
that the IO data are transferred in real-time without being affected by Ethernet standard services. The
remaining time between the RT phases (NRT channel) is used for the communication between the
Ethernet standard services. Broadband bottlenecks impair the performance of the standard services.
The real-time capability of the PROFINET IO communication is guaranteed by the reserved RT channel.
2.3 Requirements for hardware, software, and cabling
Network installation
Any switches used to network PROFINET IO devices must support the following standards and func-
tions:
• 100 Mbit/s (transfer rate of the switchports)
• Auto negotiation (automatic setting of the switchport transfer rate)
• Cut through (direct relaying of the data between the switchports)
Full duplex support for the switchports
IEEE 802.1 Q (VLAN support for Priority Class 4 or higher)
The network installation must be executed compliant with the requirements of a 100Base TX Ethernet
network with cabling to CLASS D or higher.
JUMO AQUIS touch P
To use the PROFINET IO with JUMO AQUIS touch, the device must meet the following minimum re-
quirements:
• Device software version 304.04.xx or higher
• Hardware compatibility index 0x2 or higher
The information can be displayed and reviewed with the aid of the device menu.
Open device software version:
Device menu > Device info > General > Version > SW version
Open hardware compatibility index:
Device menu > Device info > General > Version > HW compatibility index

2 Compatibility and system requirements
8

9
3 Electrical connection
3 Electrical connection
Cabling
JUMO field devices with PROFINET IO interface have two Ethernet switchports. Additional field devices,
IO controllers, an IO supervisor (programming device and/or PC for project planning) or other Ethernet
components such as switches, routers etc. can be connected to each Ethernet switchport on the device.
(1) PROFINET IO controller (PLC, control station PC or similar)
(2) JUMO PROFINET IO devices
(3) free Ethernet port (e.g. for additional PROFINET IO devices)
NOTE!
The cyclical data exchange with JUMO PROFINET IO devices is based on the RT protocol (Confor-
mance Class B). PROFINET RT communication cannot be routed. It is thus necessary that the PROF-
INET IO controller and the IO devices be in a common broadcast domain (not connected via a router).
Ethernet standard services (webserver, access via JUMO PC setup program/PCA/PCC and e-mail func-
tion) and NRT communication (e.g. project planning on the IO supervisor, system boot, noncyclical data,
etc.) function via routers as before.
1
2
3
4
5
6
7
8
9
10
Tx+/Rx+
Tx-/Rx-
1
2
3
4
1
2
3
1
2
3
8
18
1
N
(L-)
L1
(L+)
1
2
3
4
1
2
3
4
5
6
7
8
9
10
Tx+/Rx+
Tx-/Rx-
1
2
3
4
1
2
3
1
2
3
8
18
1
N
(L-)
L1
(L+)
1
2
3
4
(1) (3)(2)

3 Electrical connection
10