JUMO flowTRANS US W01 User manual

40605000T90Z001K000
V1.00/EN/00729317/2022-01-17
JUMO flowTRANS US W01
Ultrasonic flowmeter
for liquids
Operating Manual

Further information and downloads
qr-406050-en.jumo.info

Contents
Contents
1 About this documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3 Definition of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.4 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Safe operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.2 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.3 Qualification of personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.4 Hot media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.5 Hazardous materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3 Device Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.3 Nameplate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.1.1 Measuring range and accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.1.2 Reference conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2.1 Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2.2 Digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.3 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.4 Mechanical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.4.1 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.4.2 Nominal pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.4.3 Pressure loss diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.5 Measurement media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.6 Environmental influences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Acceptance of goods, storage, and transport . . . . . . . . . . . . . . . . . . . . . 14
5.1 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.2 Checking the delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.4 Packaging and transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.1 Prepare installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
6.2 Installing the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Contents
7 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.1 Preparing the electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
7.1.1 Pin assignment of the M12 connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
7.1.2 Connection of analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
7.1.3 Connection of digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
7.2 Connecting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
8 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1 Display and control elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
8.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
9 Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9.1 Cleaning device housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
9.2 Cleaning parts that come into contact with the medium and replacing O-rings . . . . . . . . . .23
9.3 Decontaminating the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
10 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.1 Uninstalling the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
10.2 Returning devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
10.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
11 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
12 China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5
1 About this documentation
1 About this documentation
1.1 Purpose
This documentation is part of the device and includes all information to ensure that it is used safely and
as intended across all phases of the product lifecycle.
If you do not follow the documentation and safety information, this may result in risk to life and damage
to property due to improper use.
• Follow the documentation and the safety information and warnings.
• Store the document in its entirety, in an easily accessible location, and so that it can be read in full
at all times.
• Contact the manufacturer if you have any questions about the device and documentation.
1.2 Target group
This documentation is intended to be used by trained electrical, mechanical, and plant engineering per-
sonnel across all phases of the product lifecycle.
1.3 Definition of terms
1.4 Symbols
Use in the documentation Definition
Device, inline device, product Ultrasonic flowmeter 406050
Medium, measurement medium, fluid Liquid
Transducer Ultrasonic converter, sensor
Product lifecycle Overall consideration of Product identification, ac-
ceptance of the goods, storage, mounting, connec-
tion, operation, troubleshooting, maintenance to
disposal
NOTE!
This symbol refers to important information about the product, its handling, or additional benefits.
NOTE!
This symbol is used in tables and indicates that further information is provided after the table.
?
REFERENCE!
This symbol refers to further information in other sections, chapters, or other manuals.

6
2 Safety
2Safety
2.1 Safe operation
This device is built based on current state-of-the-art technology and is safe to use. The device has been
tested and was shipped from the plant in perfect working order.
If you do not follow the measures to ensure safe operation, this may result in risk to life and damage to
property due to improper use.
• Only ever use the device for its intended purpose.
• Do not place the device and the process connections under mechanical strain.
• Systematically check that the process connections are leak-tight.
• Protect the device from electromechanical interference and UV radiation.
• Protect the device from the weather (when using outside).
• Only perform modifications and repairs to the device if expressly permitted by the documentation.
2.2 Intended use
The ultrasonic flow meter measures the volume flow of conductive and non-conductive media. The vol-
ume flows can be output in analogue as a current signal (4 to 20 mA) and digitally as a pulse signal
(0 to 10 kHz).
During operation, the admissible data and operating conditions specified in the legal documents and op-
erating manual must be observed.
2.3 Qualification of personnel
The personnel deployed must meet the following requirements in all phases of the product lifecycle:
• Trained electrical, mechanical, and plant engineering personnel.
• Members of personnel are familiar with this documentation and the safety information and warnings
it contains.
2.4 Hot media
Hot media may result in the device surfaces becoming hot and presenting a risk of injury.
• Allow the device and plant to cool down.
• Wear suitable protective equipment.
• Take into account alignment of the housing for electronic components.
"Alignment of the housing for electronic components", Page 16
• If required, install contact protection.
Usage Suitable Not suitable
Continuous measurement of the volume flow x
Conductive and non-conductive media x
Potentially explosive areas and safety applications x

7
2 Safety
2.5 Hazardous materials
Using hazardous materials as a medium may result in abrasive and corrosive damage to components
of the device that come into contact with the medium. The medium may leak and present a fire hazard
and a risk to health.
Carry out a risk assessment taking into consideration the safety data sheet for the hazardous substances
concerned for mounting, operation, maintenance, cleaning, and disposal:
• Comparison and systematic checking of the durability of the components of the device that come into
contact with the medium and the admissible environmental influences.
• Assessment of the risk to people and the environment.
• Assessment of the fire hazard due to the device materials, the admissible environmental influences,
and the voltage supply.

8
3 Device Description
3 Devic e Descript ion
3.1 Design
3.2 Function
The transducers are on opposite sides of the meter run and act as transmitters and receivers, i.e. they
convert the electrical energy into sound waves and the sound waves into electrical energy.
The electronic components supply power to the device, convert the raw signals into standard signals for
communicating with other systems (PLC, recorder, indicating device, etc.), and provide interfaces for dis-
playing measured values.
Function principle
Front view Rear view
(1) Meter run (4) Device status LED
(2) Transducer (ultrasonic converter) (5) O-ring (seal for the process connection)
(3) Housing for electronic components (6) M12 plug connection (4-pole)
(1)
(2)
(3)
(5)
(6)
(4)
The ultrasonic flowmeter works
according to the runtime method.
This method measures the run-
times t1 and t2 required by the
sound to travel from transducer A
to transducer B and vice versa.
= Flow direction
meter run (sectional view)
The runtime differential Δt is di-
rectly proportional to the flow ve-
locity of the medium.
A
B
t0t1t2
Δt
Δt = t - t
21
BA
AB

9
3 Device Description
3.3 Nameplate
(1) Manufacturer and device designation (9) Measuring range
(2) Product group number (10) Voltage supply
(3) Part no. ( Symbol for direct voltage)
(4) Fabrication number (11) Output signal
(5) Fabrication number as a DMC code (12) EU conformity label
(6) Nominal width (13) UK conformity label
(7) Nominal pressure level (14) Observe device documentation!
(8) Medium temperature
36039 Fulda Germany
(2)(3)(6)(7) (12) (13)
(8) (4)
(5)
(11)
(10)
(1)
(9)
(14)
READ THE DOCUMENTATION!
This symbol, which is attached to the device, indicates that the associated documentation for the de-
vice must be observed. This is necessary to identify the nature of the potential hazard, and to take
measures to prevent it.

10
4 Technical data
4 Technical data
4.1 Input
4.1.1 Measuring range and accuracy
4.1.2 Reference conditions
Nominal width Default settings for analog outputa,
b
Flowmaxa
DN 15 (Low-flow calibration) 0 to 30 l/min 60 l/min
DN 15 0 to 62.5 l/min 80 l/min
DN 20 0 to 105 l/min 210 l/min
DN 25 0 to 160 l/min 320 l/min
DN 32 0 to 260 l/min 520 l/min
aLow flow cut off: 0.05 % of flowmax.
bOptionally expandable up to flowmax.
X= Flow
max (%)
Y = Measuring deviation from the
measured value ± (%)
Measuring deviationa
Pulse output ≤ ±2.0 % of measured value ±0.1 % of flowmax
Current output Like pulse output, additionally ≤ ±0.1 % of 20 mA
Voltage output Like pulse output, additionally ≤ ±0.1 % of 10 V
Reproducibility ≤ ±0.5 % of measured valuea±0.03 % of flowmax
Temperature drift ≤ ±0.15% of measured valuea per 10 K temperature change (at -20 to +80° C)
Response time t90 ≤2s
aUnder reference conditions.
1
2
3
4
5
6
7
8
9
10
0
0 10 20 40 60 80 100
30 50 70 90
%
%
X
Y
Measurement medium Water
Medium temperature 23 °C (73 °F) ±5 K
Ambient temperature 23 °C (73 °F) ±5 K
Medium pressure 1 to 4 bar
Meter run Horizontal installation, compliance with the required inlet and outlet sections

11
4 Technical data
4.2 Output
4.2.1 Analog output
4.2.2 Digital output
Type Current output
Function Output of the current flow rate, output of a signal for error messages, display
via device status LED
Signal range 4 to 20 mA
Signal limits 3.8 to 20.5 mA
Error message 3.4 or 22 mA (default settings: 3.4 mA)
Temperature influence 75 ppm/K
Burden ≤ 500 Ω
Burden influence ≤ ±0.02 % per 100 Ω
Type Voltage output (optionally)
Function Output of the current flow rate, output of a signal for error messages, display
via device status LED
Signal range DC 0 to 10 V
Signal limits DC 0 to 10.3 V
Error message DC 0 or 11 V (default settings: 0 V)
Temperature influence 75 ppm/K
Burden ≥ 700 Ω
Burden influence ≤ ±0.02 % per 100 Ω
Type Transistor output
Function Pulse output
Switching output Push-Pull, PNP/NPN (optionally)
Ampacity ≤ 200 mA
Voltage drop ≤ 2 V
Protection Against polarity reversal, short circuiting and overload
Pulse frequency 0 to 10 kHz
Duty cycle 50 %
Output value at nominal width Pulses per Liter (l)
DN 15 (Low-flow calibration) 10000
DN 15 4800
DN 20 2850
DN 25 1875
DN 32 1150

4 Technical data
12
4.3 Electrical data
4.4 Mechanical features
4.4.1 Materials
4.4.2 Nominal pressure
4.4.3 Pressure loss diagram
Created under reference conditions "Reference conditions", Page 10.
Voltage supply DC 18 to 30 V SELV, PELV, Class 2
Current consumption 50 mA, with digital output 300 mA
Power consumption ≤ 10 W
Protection rating DIN EN 61140, Class III (protective low voltage )
Electrical safety The device must be equipped with an electrical circuit that meets the require-
ments of DIN EN 61010-1 with regard to "Limited-energy circuits".
Housing PA66-GF25
Components in contact with the
medium
Meter run PPSU
Transducer PEEK
Seals
Process connection, transduc-
er
EPDM or FKM (optionally)
Approvals
Components in contact with the
medium
Drinking water certified materials (when using EPDM seals)
Nominal pressure levels PN 16
X = Flow ratemax (%)
Y = Pressure loss (mbar)
0
50
100
150
200
250
0510 15 20 25 30 40 45 50
X
Y
mbar
35 %
DN 15
DN 25
DN 20
DN 15 low
DN 32

13
4 Technical data
4.5 Measurement media
4.6 Environmental influences
Medium type Conductive or non-conductive liquids
Viscosity ≤ 100 mPas
Foreign matter content
Solids ≤ 5 % vol
Gases ≤ 1 % vol
Medium temperature
Temperature range -20 to +95 °C
within the accuracy specifications -20 to +80 °C
outside of the accuracy specifica-
tionsa
>80to95°C
aReturn to the accuracy specifications after cooling down.
Admissible ambient temperature DIN 60068-2-1, DIN 60068-2-2
at a medium temperature of
≤80°C
-20to+70°C
at a medium temperature of
>80°C
-20to+45°C
Climatic conditions DIN EN 60721-3-1, DIN EN 60721-3-3, DIN EN 60068-2-78
Climate class 3K6
Temperature range -20 to +55 °C
Relative humidity ≤ 100 % – Condensation on device outer shell
Protection type DIN EN 60529, EN 50102
IP65, IP67
Electromagnetic compatibility
(EMC)
DIN EN 61326-1, DIN EN 61326-2-3
Interference emission Class Ba
Interference immunity Industrial requirements
Vibration resistance DIN EN 60068-2-6, DIN EN 60068-2-27
Vibration resistance 5 g at 10 to 2000 Hz
Shock resistance 20 g over 11 ms
Pressure Equipment Directive 2014/68/EU
Group 1 fluids - DN ≤ 25 Sound engineering practice acc. to Art. 4, para. 3 i. c. w. Art. 4 para. 1c.i
Group 2 fluids - DN ≤ 32 Sound engineering practice acc. to Art. 4, para. 3 i. c. w. Art. 4 para. 1c.i
Group 1 fluids Sound engineering practice acc. to Art. 4, para. 3 i. c. w. Art. 4 para. 1c.ii
aThe product is suitable for industrial use as well as for households and small businesses.

14
5 Acceptance of goods, storage, and transport
5 Acceptance of goods, storage, and transport
5.1 Scope of delivery
5.2 Checking the delivery
• Ensure that the packaging and its contents are undamaged.
• Check the delivery for completeness against the packing slip and order details.
• Inform the supplier immediately if there is any damage.
• Store damaged parts until clarification is received from the supplier.
5.3 Storage
Improper storage may result in damage to the device.
• Store the device in a dry and dust-free environment.
• Observe the device storage temperature range.
5.4 Packaging and transport
If the device is not protected properly against external influences, it may become damaged during trans-
port.
• Transport the device in an impact-proof packaging solution that protects it against moisture and dirt.
• Also comply with the admissible storage temperatures while the device is being transported.
• Seal any electrical interfaces with protective caps to protect them against damage.
1× JUMO flowTRANS US W01 – Device in the ordered version, including test certificate
2× O-ring (seal for the process connection) in the ordered version
1× JUMO flowTRANS US W01 operating manual

15
6 Installation
6 Installation
6.1 Prepare installation
Requirements:
• Check the environmental influences to which the device will be exposed.
• Switch off the plant's voltage and secure it so that it cannot switch on again.
• Stop medium circulation in the plant.
• Drain and flush the pipe.
• Wear suitable protective equipment.
• Correctly prepare the pipe for installation.
• Use only suitable tools when working on the device and plant.
Inlet and outlet sections
Installation position
To calm the flow in the pipeline,
the specified inlet and outlet sec-
tions are required at the very
least.
For increased accuracy, the inlet
and outlet sections can be made
longer.
DN = Nominal pipe width
= Flow direction
1× 90° manifold or T-piece 2× 90° manifolds
Pipe extension Pipe reduction
3× DN
5× DN
3× DN
5× DN
3× DN
5× DN
3× DN
5× DN
Mount the device in either the hor-
izontal or vertical pipe.
Requirements:
• The pipe around the transduc-
ers must be filled.
• The flow direction ( ) must
run upward when mounting
vertically.
• Avoid the formation of air bub-
bles in the pipe and right at
the device.
Correct Incorrect

6 Installation
16
Avoid mechanical strain
Flow direction
Alignment of the housing for electronic components
Ensure that the center lines of
both ends of the pipes align be-
fore installing in the pipe (3).
Align the ends of the pipes parallel
and at an angle to one another.
Adhere to the insertion length L of
the device.
Installation accessories are avail-
able from the manufacturer.
Each mounting set contains two
union ends (1) and two union nuts
(2). Select the correct set for the
nominal width and pipe material in
question.
For the table of dimensions for the
mounting sets, please see:
Data sheet.
Nominal width Insertion length L [mm]
DN 15 160
DN 20 165
DN 25 175
DN 32 185
A
A
L(1) (2) (3)
The positive flow direction ( ) is
shown on the transducer covers
on both sides of the device and
must be observed during installa-
tion, in accordance with the appli-
cation in question.
CAUTION! Protect the electronics
housing from being heated up by
hot media. Install the electronics
housing at medium tempera-
tures> 60 ° C (140 ° F) aligned 90
° to the side!
Front view Side view
90°

17
6 Installation
6.2 Installing the device
1. Insert the O-rings supplied into
the sealing ring grooves in the
two process connections.
2. Install the device between the
two union ends of the mounting
set.
Ensure that the O-rings (2) be-
tween the process connections
(1) and union ends (3) are cor-
rectly positioned.
3. Manually screw union nuts on
both ends of the pipe to the pro-
cess connections on the device.
The device is now installed in the pipe.
(2)
(3)
(1)
(1)

18
7 Electrical connection
7 Electrical connection
7.1 Preparing the electrical connection
Requirements:
• Switch off the plant's voltage and secure it so that it cannot switch on again.
• Correctly prepare the connections for the voltage supply and signal processing. The device must be
equipped with an electrical circuit that meets the requirements of DIN EN 61010-1 with regard to
"Limited-energy circuits".
• Voltage supply: DC 18 to 30 V SELV, PELV.
• Use a cable that has a temperature resistance suitable for the process.
• Do not lay the cable near high-voltage or high-frequency cables; if you cannot avoid doing so, main-
tain a minimum gap of 30 cm.
7.1.1 Pin assignment of the M12 connector
Connection Device Connecting cablea
aConnecting cable for plug connector M12 "Accessories", Page 25.
Pin assignment and color codingb
bThe color coding is only valid for A-coded standard cables!
Figure
Voltage supply V+
(DC18to30V)
(1) (1) BN (brown)
Analog output (2) (2) WH (white)
GND (3) (3) BU (blue)
Digital output (4) (4) BK (black)
Connection type Plug connector M12 Plug connector M12 with screw
locking
M12
M12
(3)
(4)
(1)
(2)
(3)
(4)
(1)
(2)

19
7 Electrical connection
7.1.2 Connection of analog output
Current output – 4 to 20 mA
Voltage output – 0 to 10 V (optionally)
7.1.3 Connection of digital output
Requirements:
• Connect an unused current output (2) to GND (3).
• Leave an unused optional voltage output (2) open.
Pulse output – push-pull (example 1)
Device Connecting cable
Device Connecting cable
(1)
(2)
(4)
(3)
+24 V
GND
R
A
≤ 500 Ω
+24 V
GND
V
≥ 700 Ω
R
(1)
(2)
(4)
(3)
Device Connecting cable
+24 V
GND
≤ 200 mA, ≤ 10 kHz
(1)
(2)
(4)
(3)

7 Electrical connection
20
Pulse output – push-pull (example 2)
Pulse output – NPN (optionally)
Pulse output – PNP (optionally)
Device Connecting cable
Device Connecting cable
Device Connecting cable
+24 V
GND
≤ 200 mA, ≤ 10 kHz
(1)
(2)
(4)
(3)
+24 V
GND
≤ 200 mA, ≤ 10 kHz
(1)
(2)
(4)
(3)
+24 V
GND
≤ 200 mA, ≤ 10 kHz
(1)
(2)
(4)
(3)