Kärcher SC 1 User manual

SC 1 Upright 
KST 1 Upright
97744660 (10/23)

A

B
G
CD
E F
H I J
K L M
CLICK
CLICK
CLICK
a b
1.
3.
4.
2.

N
2.

6English
Contents
Safety instructions
Read this safety chapter and these origi-
nal instructions before using the device
for the first time. Act in accordance with
them. Keep the original instructions for future reference
or for future owners.
●In addition to the notes in the operating instructions,
you also need to take into consideration the general
safety regulations and accident prevention guide-
lines applicable by law.
●Warnings and information notices attached to the
device provide important information for hazard-free
operation.
Hazard levels
DANGER
●Indication of an imminent threat of danger that will
lead to severe injuries or even death.
몇WARNING
●Indication of a potentially dangerous situation that
may lead to severe injuries or even death.
몇CAUTION
●Indication of a potentially dangerous situation that
may lead to minor injuries.
ATTENTION
●Indication of a potentially dangerous situation that
may lead to damage to property.
General safety instructions
DANGER ● Risk of asphyxiation. Keep pack-
aging film out of the reach of children.
몇WARNING ● Only use the device for its proper
use. Take into account the local conditions and beware
of third parties, in particular children, when working with
the device. ● Only people who have been instructed on
how to use the device, or have proven their ability to op-
erate it, and have been explicitly instructed to use it,
must use the device. ● Persons with reduced physical,
sensory or mental capabilities and persons lacking ex-
perience and knowledge may only use the appliance if
they are properly supervised, have been instructed on
use of the appliance safely by a person responsible for
their safety, and understand the resultant hazards in-
volved. ● Children must not operate the device. ● Chil-
dren must be supervised to prevent them from playing
with the appliance. ● Keep the device out of the reach of
children when it is connected to the mains or when it is
cooling down.
몇CAUTION ● Do not use the device if it has
been dropped beforehand, is visibly damaged or if it is
leaking. ● Safety devices are provided for your own pro-
tection. Never modify or bypass safety devices.
Risk of electric shock
DANGER ● Never touch the mains plug and
socket with wet hands. ● Only connect the device to al-
ternating current. The voltage indicated on the type
plate must match the voltage of the power source. ● Do
not direct the steam jet directly onto equipment contain-
ing electrical components, e.g. the interior space of ov-
ens. ● Do not fill the devices with removable water
reservoir directly via the water connection while they are
connected to the mains power. Use a receptacle for fill-
ing. ● Do not use the d in swimming pools which contain
water. ● The mains plug and extension cable connec-
tion must not be in water. ● Do not clean over floor
sockets.
몇WARNING ● Only connect the device to an
electrical connection which has been set up by a quali-
fied electrician as per IEC 60364-1. ● Only operate the
device in wet rooms, e.g. bathroom, connected to sock-
ets with upstream residual current device. ● Check that
the mains connection cable with mains plug is undam-
aged each time before using the device. To avoid any
possible danger, a damaged mains connection cable
must be immediately replaced by the manufacturer, or
the authorised customer service department or a quali-
fied electrician. ● Do not damage the power supply and
extension cable by running over it, crushing or yanking
it or similar. Protect the power supply cable from heat,
oil and sharp edges. ● Unsuitable electrical extension
cables can be dangerous. Only use electrical extension
cables with a splash guard and a diameter of at least
3x1 mm2.● Only replace couplings on the power supply
or extension cable with those with the same splash
guard and the same mechanical strength. ● Clean tiled
walls with sockets carefully. ● Disconnect the device
from the mains during longer operating breaks, after use
or before performing any maintenance work. ● Only
carry out servicing work when the mains plug is pulled
and the steam cleaner has cooled down.
Operation
DANGER ● Operation in explosive atmos-
pheres is prohibited. ● When using the device in hazard
zones (e.g. service stations), adhere to the respective
safety regulations.
몇WARNING ● Risk of scalding. Never touch the
steam jet with your hand from a close distance, and do
not direct it at people or animals. ● Danger of scalding
from high water output if you tilt the device more than
30° to the side during use. Only affects SC 1 devices ● Risk
of scalding on the hot steam boiler. Allow the steam boil-
er to cool down before filling it with water. Does not apply
to SC 1 Upright / KST 1 Upright / SC 2 Upright / KST 2 Upright /
SC 3 / SC 3 Upright devices ● Risk of scalding. Let the ap-
pliance and accessory parts, particularly the floor clean-
ing cloth and the hand cover cool down before touching
them. ● Risk of scalding. Do not use the appliance for
cleaning pressure tanks as this poses a bursting and ex-
plosion hazard. ● Risk of scalding from the floor nozzle.
Safety instructions ............................................... 6
Intended use........................................................ 8
Environmental protection..................................... 8
Accessories and spare parts ............................... 8
Scope of delivery ................................................. 8
Safety devices ..................................................... 8
Description of the device ..................................... 8
Installation ........................................................... 8
Initial Start-Up...................................................... 9
Operation............................................................. 9
Important application instructions........................ 10
How to use the Accessories ................................ 10
Care and service ................................................. 10
Troubleshooting guide ......................................... 11
Warranty .............................................................. 11
Technical data ..................................................... 11

English 7
Ensure that no part of the body gets under the floor noz-
zle. Never operated the floor nozzle without wearing
shoes. ● Risk of scalding. Only operate the appliance
once it is fully assembled and functional. ● Risk of
scalding. Let the appliance cool down fully before put-
ting it away.ATTENTION ● Do not fill with any
cleaning agents or other supplements. ● Do not use vin-
egar or similar agents.WARNING ● Never discon-
nect accessories from the device while steam is being
expelled. ● Hot water may drip out when disconnecting
accessory parts. Allow the device to cool down first.
● Never open the maintenance / safety lock during op-
eration. Allow the device to cool down first. ● Do not
clamp the steam lever / steam key during operation.
● Replace a damaged steam hose immediately with a
steam hose as recommended by the manufacturer.
● Do not steam any objects which contain harmful sub-
stances (e.g. asbestos).
몇CAUTION ● Only operate or store the device
in accordance with the description or figure. ● Check
the device and the accessories, in particular the power
supply cable, safety lock and steam hose, to make sure
it is in proper safe and reliable condition before opera-
tion each time. Do not use the device if it is damaged.
Replace damaged components immediately. ● Only
switch on the device when water is present in the steam
boiler. The device may otherwise overheat, see the
Troubleshooting chapter of the operating instructions.
● Accidents or damage due to the device falling over.
Before all actions with or on the device, you must make
sure that it is stable. ● Do not carry the device when per-
forming cleaning work.
ATTENTION ● Do not operate the device at tem-
peratures below 0 °C. ● Never leave the device unsu-
pervised while it is connected to the mains. ● Do not use
the appliance as a humidifier or heater. ● Ensure the
room is well ventilated when working with the appliance
and afterwards. ● Protect the device from rain. Do not
store the device outdoors. ● Device damage. Never
pour solvents, liquids containing solvents or undiluted
acids (e.g. detergents, petrol, paint thinner and acetone)
into the boiler/water reservoir. ● Unsuitable water can
block the nozzles or damage the water level indicator.
Do not fill with condensate water from a tumble dryer,
collected rainwater, detergents or additives
(e.g. scents). Fill the water reservoir with a maximum of
0.2 l / 0.4 l / 0.5 / 1 l of tap water. Only applies to SC 1 Up-
right / KST 1 Upright / SC 2 Upright / KST 2 Upright / SC 3 Upright
/ SC 3 devices ● Unsuitable water can block the nozzles
or damage the water level indicator. Do not fill with pure
distilled water, condensation from a dryer, collected rain
water, detergents or additives (e.g. fragrances), use a
maximum of 50% distilled water mixed with tap water.
●Remove the water reservoir for filling
a Pull the water reservoir vertically in an upward di-
rection
b Fill the water reservoir vertically with tap water or
a mixture of tap water and a maximum of 50%
distilled water up to the “MAX” marking.
c Insert the water reservoir and press down until it
clicks into place.
●Fill the water reservoir directly at the device
a Fill tap water or a mixture of tap water and a max-
imum of 50% distilled water up to the “MAX”
marking in the filling hole for the water reservoir.
Applies only to SC 4 and SC 5 devices
Note ● Refilling water
1 Switch off the device.
2 Allow the device to cool down.
3 Unscrew the safety lock.
4 Drain the water completely out of the steam boiler.
5 Fill a maximum of 200 ml distilled water or tap water
into the steam boiler.
6 Insert the safety lock.
Applies only to SC 1 devices ● Refilling water
1 Switch off the device.
2 Allow the device to cool down.
3 Unscrew the safety lock.
4 Drain the water completely out of the steam boiler.
5 Fill a maximum of 1 l distilled water or tap water into
the steam boiler.
6 Insert the safety lock.
Applies only to SC 2 / KST 2 devices
For upright machines
몇WARNING ● Risk of scalding. Only operate
the device on even, horizontal surfaces. Do not lay the
device on its side during operation. Do not use the de-
vice above head height or horizontally e.g. to clean
walls, work surfaces or windows. Only applies to SC 1 Up-
right / KST 1 Upright / SC 2 Upright / KST 2 Upright / SC 3 Upright
몇CAUTION ● In order to guarantee stability,
place the device on a firm, flat surface.
Care and service
몇CAUTION ● Have repair work carried out by
the authorised customer service only.
Descaling the steam boiler
Does not apply to SC 1 Upright / KST 1 Upright / SC 2 Upright /
KST 2 Upright / SC 3 / SC 3 Upright devices
몇CAUTION ● Never screw the safety lock onto
the device while descaling. ● Do not use the steam
cleaner while there is descaler in the boiler.
ATTENTION ● The descaler may corrode sensi-
tive surfaces. Work carefully when filling and emptying
the steam cleaner with descaler.
ATTENTION ● Do not use vinegar or similar
agents.
Steam cleaner accessories
(Depending on equipment)
Iron
몇WARNING ● Risk of scalding. Do not direct
the steam jet at people or animals. ● Risk of burns on
hot steam pressure iron and hot steam jet. Alert other
people to the hazard. ● Do not touch any electrical ca-
bles or combustible objects with the hot steam pressure
iron. ● Have the damaged mains cable replaced imme-
diately by an authorized customer service/qualified
electrician. ● Children over the age of 8 and persons
with reduced physical, sensory or mental capabilities, or
those with a lack of experience and knowledge, are only
allowed to use the appliance if they are properly super-
vised, have been instructed with respect to using the ap-
pliance safely by a person responsible for their safety,
and understand the resultant dangers involved. ● Chil-
dren must not play with the appliance. ● Children may
only perform cleaning work and user maintenance un-
der supervision.
몇CAUTION ● Do not use the steam pressure
iron if it has been dropped, has visible damage or is
leaking. ● Do not leave the steam pressure iron unat-

8English
tended while it is connected to the mains. ● Before the
water reservoir (of the steam cleaner) is filled with water,
the mains plug must be pulled out of the socket. ● You
must only operate or set down the steam pressure iron
on a stable surface. ● When placing the steam pres-
sure iron on its stand, make sure that the stand is stable.
● Repair work on the device may only be carried out by
authorized customer service.
Steam turbo brush
몇CAUTION
●Longer periods of use of the steam turbo brush may
lead to poor blood circulation in the hands due to vi-
bration. In case of symptoms, e.g. tingling in the fin-
gers, cold fingers, take a break. A general period of
use cannot be set, because this depends on several
influencing factors:
●Personal tendency to suffer from poor circulation
(frequently cold fingers, tingling sensation in the fin-
gers).
●Holding the device too tightly hindering blood circu-
lation.
●Continuous operation is more harmful than opera-
tion interrupted by work breaks.
You should consult a doctor if using the steam turbo
brush regularly and for lengthy periods of time, and in
the event of repeated occurrences of symptoms such
as tingling in the fingers or cold fingers.
Intended use
Use the device only in private households for cleaning
level hard floors (e.g stone floors, tiles, PVC floors, as
well as sealed wooden floors such as parquet and lam-
inate) that can withstand the high temperature, pressure
and moisture of the device. Do not clean any water-sen-
sitive coverings such as untreated cork floors (moisture
can penetrate and damage the floor).
Cleaning agents are not required.
Environmental protection
The packing materials can be recycled. Please
dispose of packaging in accordance with the en-
vironmental regulations.
Electrical and electronic devices contain valua-
ble, recyclable materials and often components
such as batteries, rechargeable batteries or oil,
which - if handled or disposed of incorrectly - can
pose a potential danger to human health and the envi-
ronment. However, these components are required for
the correct operation of the device. Devices marked by
this symbol are not allowed to be disposed of together
with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found
at: www.kaercher.de/REACH
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the
packaging. Check the contents for completeness when
unpacking. If any accessories are missing or in the
event of any shipping damage, please notify your deal-
er.
Safety devices
몇CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection.
Never modify or bypass safety devices.
Symbols on the device
(according to type of appliance)
Safety valve
In the case of excessively high pressure in the event of
a fault, a safety valve relieves the pressure into the at-
mosphere.
Fuse
The fuse prevents the device from overheating. If the
device overheats, the fuse disconnects the device from
the power supply.
Before re-commissioning the device, contact the re-
sponsible KÄRCHER Customer Service.
Description of the device
The maximum amount of equipment is described in
these operating instructions. Depending on the model
used, there are differences in the scope of delivery (see
packaging).
For the illustrations, see graphics page.
Illustration A
1Handle
2Cable hook with cable fastener
3Decalcification cartridge
4Mains connection with mains plug
5Steam ON/OFF switch
6Floor head
7Hook and loop fastener
8Power-on indicator
9Water reservoir
10 Unlocking button for device handle
11 Floor cloth
Installation
Installing the device handle
1. Fit the three parts of the device handle into each oth-
er in order until it audibly latches into place.
2. Hold the basic device firmly.
3. Fit the device handle all the way to the end stop into
the basic device until it audibly latches into place.
4. The device handle must sit tightly in the device.
Illustration B
Risk of burns, surface of appliance be-
comes hot during operation
Risk of scalding from steam
Read operating instructions

English 9
Installing the floor cleaning cloth
1. Attach the floor cleaning cloth to the floor head.
a Place the floor cleaning cloth with the hook and
loop strips pointing upwards on the floor.
b Place the floor head onto the floor cleaning cloth,
applying slight pressure.
Illustration G
The floor cleaning cloth will stick to the floor head of
its own accord due to the hook and loop fastener.
Initial Start-Up
ATTENTION
Device damage due to calcification
Always work with a decalcification cartridge.
1. Press the latching hook of the water reservoir up-
wards and pull out the water reservoir.
Illustration C
2. Unpack the decalcification cartridge.
3. Write down the first use date of the decalcification
cartridge on the warning label.
Note
Please label with a waterproof pen.
4. Insert the decalcification cartridge into the device
and press it firmly into place.
Note
Please replace the decalcification cartridge in 4 months
or a flow of approx. 15 l of water.
Operation
Filling water
The water reservoir can be filled at any time.
ATTENTION
Material damage through open reservoir cover or
incorrectly seated or loose water reservoir
Liquid can escape and damage the floor covering if the
reservoir cover is not correctly closed or the water res-
ervoir is not correctly inserted into the device.
Take care to ensure that the reservoir cover is securely
closed and the water reservoir is seated tightly in the de-
vice when the water reservoir is full.
ATTENTION
Damage to the device
Unsuitable water can block the nozzles.
Do not use condensation from the clothes dryer for fill-
ing.
Do not use collected rain water for filling.
Do not use cleaning agents or other additives (e.g.
scents) for filling.
Filling the water reservoir directly on the device
1. Hold the device firmly.
2. Open the reservoir cover, and turn it to the side.
3. Fill with max 0.2 l tap water directly at the device.
Illustration D
4. Close the reservoir cover.
Removing the water reservoir for filling
1. Press the latching hook of the water reservoir up-
wards and pull out the water reservoir.
2. Open the reservoir cover, and turn it to the side.
3. Fill with max 0.2 l tap water.
Illustration E
4. Close the reservoir cover.
5. Insert the water reservoir and press it firmly into
place.
Unwinding the power cable
몇WARNING
Risk of electric shock
If the power cable is not completely unwound, the dan-
ger exists of you straining and damaging the power ca-
ble by overestimating the range of the cable.
Always completely unwind the power cable.
Note
The lower cable holder can be rotated by 360° for re-
moving the cable. The upper cable hook cannot be ro-
tated.
1. Turn the lower cable holder upwards.
2. Remove the power cable completely from the cable
hook.
3. Fasten the cable in the fastener of the upper hook to
prevent it from being run over during cleaning work.
Illustration F
Switching on the device
Installation information
When steaming for the first time after removing and re-
inserting the decalcification cartridge, the steam jet
maybe weak or irregular, and individual drops of water
may be expelled. The device requires a short running-in
period in which the decalcification cartridge fills with wa-
ter.The steam volume that is expelled increases con-
stantly until the maximum steam volume has been
reached after approx. 20 seconds.
1. Place the device on a firm surface.
Illustration H
2. Plug the mains plug into a mains socket.
3. The power-on indicator light lights up constantly
green.
Illustration I
After waiting for approx. 30 seconds, the device is
ready for use.
4. Press the steam on/off switch by foot. The steam
comes out.
Illustration J
Refilling water
Note
If there is a water shortage, the pump sounds loud and
there’s no visible steam.
When the water is refilled, the decalcification cartridge
remains fixed in the device.
ATTENTION
The device is equipped with dry-run protection for the
pump. If the pump runs dry for a longer period, e.g. be-
cause the decalcification cartridge and the water reser-
voir are not correctly inserted, the pump is overheating
and switches off. To be able to operate the device again,
the device has to be switched off and wait the pump to
be cool down for approx. 10 minutes. In the process,
you must make sure that the cartridge and the water
reservoir have been inserted correctly and there is
enough water in the water reservoir.
Press the steam on/off switch by foot. The steam
stops in few seconds.
Open the reservoir cover, and fill the water reservoir
with max. 0.2 l tap water directly at the device.
Illustration D
or
Remove the water reservoir, open the reservoir cov-
er, and fill with max. 0.2 l tap water, see chapter Fill-
ing water.
Illustration E

10 English
Interrupting operation
ATTENTION
Material damage due to condensate/moisture
The floor covering can be damaged by moisture remain-
ing on the floor cleaning cloth or device after cleaning.
Remove the floor cleaning cloth and dry the device after
finishing the cleaning work.
Do not place or store the device on heat-sensitive sur-
faces.
ATTENTION
Damage to the material and the device
The floor covering and the device can be damaged by
consistently steam while the device stands still.
Switch off the device every time you leave.
Press the steam on/off switch by foot. The steam stops
in few seconds.
In order to save energy, we recommend that you switch
off the device for breaks in operation of longer than 20
minutes.
1. Press the steam on/off switch by foot. The steam
stops in few seconds.
2. Pull the mains plug out of the socket.
Illustration K
3. Park the device.
Illustration H
Switching off the device
1. Press the steam on/off switch by foot. The steam
stops in few seconds.
2. Pull the mains plug out of the socket.
Illustration K
3. To drain the water reservoir, see chapter Draining
the water reservoir.
Illustration L
Storing the device
1. To remove the floor cleaning cloth, see chapter How
to use the Accessories.
Illustration G
2. Remove the moisture from the device.
3. Wind the power cable around the lower and upper
cable hooks.
Illustration M
4. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
The device is suitable for cleaning washable floor cov-
erings, e.g. stone floors, tiles and PVC floors, as well as
sealed wooden floors such as parquet and laminate.
ATTENTION
Damage due to steam effect
Heat and the effects of steam can lead to dam-
age.Check the heat resistance and steam effect on an
inconspicuous area using a minimal volume of steam
prior to use.
Do not remain the steam in the same position on the
sealed wooden floors for too long.
Note
Detergent residues or care emulsions on the surface to
be cleaned can cause streaks during steam cleaning,
but these disappear after repeated use.
몇CAUTION
Beware of burns to your feet
The floor head/floor cleaning cloth heats up during
steaming.
Hot water may drip out when pulling off the floor cloth.
Only operate or remove the floor head/floor cleaning
cloth with suitable footwear.
For fastening the floor cleaning cloth to the floor head,
please refer to chapter How to use the Accessories
How to use the Accessories
Floor cloth
The floor cloth is suitable for cleaning stone floors, tiles
and PVC floors, and also sealed wooden floors such as
parquet and laminate.
Removing the floor cleaning cloth
Note
Please make sure the device is switched off before re-
moving the floor cleaning cloth.
1. Place one foot on the bottom corner of the floor
cleaning cloth and lift the floor head up.
Illustration G
Note
Initially, the floor cleaning cloth's hook and loop fastener
strip is very strong and cannot be removed from the
floor head easily. After the floor cleaning cloth has been
used several times and washed, it is easier to remove
from the floor head and it has reached the optimum ad-
hesion.
Care and service
Draining the water reservoir
ATTENTION
Device damage due to water putrefaction
If the device is not put into operation for more than 2
months, the water in the reservoir may putrefy.
Drain the water reservoir before breaks in operation.
1. Remove the water reservoir and open the reservoir
cover.
2. Drain the water reservoir.
Illustration L
Replacing the decalcification cartridge
ATTENTION
Device damage and shortened service life
Please replace the decalcification cartridge in 4 months
or a flow of approx. 15 l of water. If the decalcification
cartridge is not replaced in time, there is a risk of device
damage and the service life of the device may be short-
ened.
Note
Write down the first use date of the decalcification car-
tridge on the warning label.Please label with a water-
proof pen.
Note
The anti-calcification effect of the decalcification car-
tridge is activated as soon as the reservoir is filled with
water, and the device is put into operation. Lime in the
water is absorbed by the granulate in the decalcification
cartridge. Additional descaling is not required.

English 11
Note
The granulate in the decalcification cartridge may
change colour after it comes into contact with water.
This depends on the mineral content in the water. This
discolouration is harmless and does not have a nega-
tive effect on the device, the cleaning work or the func-
tionality of the decalcification cartridge.
Inserting the decalcification cartridge
ATTENTION
Device damage
There is a risk of damage to the device if the used de-
calcification cartridge is re-used.
Work carefully in order to prevent mixing up the cartridg-
es.
Installation information
When steaming for the first time after removing and re-
inserting the decalcification cartridge, the steam jet may
be weak or irregular, and individual drops of water may
be expelled. The device requires a short running-in pe-
riod in which the decalcification cartridge fills with water.
The steam volume that is expelled increases constantly
until the maximum steam volume has been reached af-
ter approx. 20 seconds.
Note
Remove the water reservoir before removing and in-
stalling the decalcification cartridge.
1. Press the steam on/off switch by foot. The steam
stops in few seconds.
2. Pull the mains plug out of the socket.
Illustration K
3. Remove the water reservoir and open the reservoir
cover.
4. Remove the decalcification cartridge.
5. Write down the first use date of the new decalcifica-
tion cartridge on the warning label.
Note
Please label with a waterproof pen.
6. Insert the new decalcification cartridge and press it
firmly into place.
Illustration N
7. Insert the mains plug into a socket.
8. Press the steam on/off switch and wait for approx.
20 seconds to vent the decalcification cartridge.
Care of accessories
(Accessories - depending on scope of delivery)
Note
The cloths are not suitable for dryer.
Note
Observe the instructions on the washing tag when
washing the cloths. Do not use any liquid softeners as
this will affect the ability of the cloths to pick up dirt.
1. Wash the floor cleaning cloths in a washing machine
at a max. temperature of 60 °C.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
몇WARNING
Risk of electric shock and burns
Trying to eliminate faults while the appliance is connect-
ed to the mains or has not yet cooled down is always
dangerous.
Remove the mains plug.
Allow the appliance to cool down.
The pump sounds loud and there is no steam.
No water in the water reservior.
Fill the water in the water reservior.
No steam / little steam although there is sufficient
water in the reservoir
The decalcification cartridge has not been inserted or
has been inserted incorrectly.
Fit the decalcification cartridge and/or check that the
decalcification cartridge sits tightly in the device and
press in again if necessary.
A new decalcification cartridge has been fitted.
Press the steam on/off switch and make sure the
pump is working by the pump sound.
The full steam output is reached after approximately
20 seconds.
The water reservoir has not been installed in place.
Check that the water reservoir is installed in place
and press in again if necessary.
Warranty
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy pos-
sible malfunctions on your device within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Subject to technical modifications.
SC 1
Upright
KST 1
Upright
Electrical connection
Voltage V 220-240
Phase ~ 1
Frequency Hz 50-60
Degree of protection IPX4
Protection class I
Device performance data
Heating capacity W 1300
Heating-up time Seconds 30
Filling quantity
Water reservoir l 0.2
Dimensions and weights
Weight (without accessories) kg 2.0
Length mm 314
Width mm 147
Height mm 1197

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
www.kaercher.com/welcome
Bewerten Sie Ihr Produkt und sagen Sie uns Ihre Meinung.
Rate your product and tell us your opinion.
Évaluer votre produit et dites-nous votre opinion.
Reseñe su producto y díganos su opinión.
Registrieren Sie Ihr Produkt und protieren Sie von vielen Vorteilen.
Register your product and benet from many advantages.
Enregistrez votre produit et bénécier de nombreux avantages.
Registre su producto y aproveche de muchas ventajas.
MERCI! DANKE! ¡GRACIAS!
THANK YOU!