KI CafeWay ECELP User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
CaféWay™Tables
Models ECELP, ECOCP & ECRDP
July 2018
Note: This instruction contains
installation steps for stool seats
(Pages 1-2), bench seats (Page 3),
and middle bench seats (Page 4).
Stool Seat Installation
1. Stools that will be installed near the
pivot point of the table are required
to use all eight mounting locations.
Stools located away from the pivot
location are only required to use
the four outer corner mounting
locations (Figure 1).
Note: Enough screws are supplied
to use all eight mounting locations
on each stool if desired.
2. Remove stools and #14 x 5/8”
attachment screws from the
shipping box. Place stool seats
upside down on a flat protective
surface.
3. Align three screws, two in each
adjoining corner, and one in
between the corners as illustrated
(Figure 2).
4. Install the three #14 x 5/8” screws,
but do not drive the screws in all
the way. Leave a 1/4” gap between
the bottom of the screw head and
stool. This will allow the stool plate
adapter to slide in between the
screw head and seat (Detail A).

2
CaféWay™Tables - Models ECELP, ECOCP, & ECRDP
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
4. Align partially installed screws
on seat with slotted holes on the
stool plate adapter (Figure 3).
5. Slide plate adapter into place and
align vacant seat mounting holes
with stool plate holes (Figure 4).
6. Install five #14 x 5/8” screws into
the vacant attachment holes and
torque to 15-20 in/lbs. Next, twist
down the three screws on the
slotted hole side and torque them
to 15-20 in/lbs (Figure 4).
Figure 3
Figure 4

CaféWay™Tables - Models ECELP, ECOCP, & ECRDP
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
3
Optional Bench Seat
Installation
1. Remove bench seat and
self-drilling wood screws from the
shipping box (Figure 5).
2. Align bumpers on underside of
bench with center holes on stool
plate adapter. This will help hold
the bench seat in place while
screws are installed (Figure 5).
3. Using the self-drilling wood
screws provided, attach bench
seat to stool plate adapter
(Figure 5).
self-drilling
wood screw
stool
plate adapter
bench seat
bumpers
Figure
5

CaféWay™Tables - Models ECELP, ECOCP, & ECRDP
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2018 Krueger International, Inc. All Rights Reserved • Code KI-62654R1/KI/PDF/0718
Optional Middle Bench
Installation
1. Fold table into the storage
position before attachment of
bench can take place (Figure 6).
2. The bench assembly is designed
to span the distance between the
vertical components of the two
middle leg assemblies, which in
the folded position are suspended
in the air (Figure 6).
3. Once the table is in the storage
position, attach the “fixed bench
leg” to the table’s middle leg
assembly. Next, slide the
“non-fixed bench leg” on the
opposite end of bench into
position so that tube can be
inserted inside the upright of
the other middle leg assembly
(Figure 7).
4. Fasten down the bench to the
table leg using a supplied 5/16”
bolt and nylock nut. Tighten
nut and bolt until the nut stops
against the pipe. The parts will
need to rotate during the opening
and closing of the table so make
sure not to over-tighten. Bolt
head must be face away from the
table (Figure 7).
5. Next, align the hole of the
“non-fixed bench leg,” to the
table’s mid leg. Fasten the bench
down to the table leg using a 5/16”
bolt and nylock. Tighten nut and
bolt until the nut stops against
the pipe. The parts will need to
rotate during the opening and
closing of the table so make sure
not to over-tighten. Bolt head
must be face away from the table
(Figure 7).
6. Test table for proper operation.
Figure 6
Figure 7