KI 700 Series User manual

Detail A
Level Connector
End
Panel
#14 x 7/8”
Screw
Wire Management
Channel
Detail B
Worksurface
AssemblyInstructions
KI700SeriesDeskCornerUnit
August1997
KI Pembroke
P.O. Box 580
1000 Olympic Drive
Pembroke, Ontario
K8A 6X7
TEL [phone]
FAX [phone]
1. To avoid scratching worksurface,
place face down on a protective
surface.
2. If attaching bridge/return, align level
connector (shipped with bridge/
return) with holes in worksurface.
Place end panel on level connector
and secure in place with (3)
#14 x 7/8” screws (Detail A).
Repeat for opposite end.
3. Using (2) #14 x 7/8” screws attach
corner column to underside of top.
4. Position modesty panel between end
panel and corner panel. Note: Double
flanged end of modesty panel
attaches to end panel. Aligning
holes use (6-8)* #8 x 1/2” screws to
attach modesty panel to corner
column and end panel. Repeat for
next modesty panel.
5. Place wire management channel on
worksurface, product label facing
inward, align holes with predrilled
holes in worksurface. Secure in
place using (3) #8 x 1/2” screws
(Detail B). Repeat for next wire
management channel.
*(6) - #8 x 1/2” screws partial
modesty panel
(8) - #8 x 1/2” screws full modesty
panel
Components
1 - Worksurface
2 - End Panel
3 - Modesty Panel
4 - Corner Column
5 - Wire Management Channel
Tools Required
ŸPhillips Screwdriver
Ÿ3/8” Socket/Wrench
Hardware Parts List
(24)#20162 - #8 x 1/2” Screws
(6) #20192 - #14 x 7/8” Screws
(8) #20203 - 10-16 x 1/2” Self Drilling
Screws
(5) #20425 - Hex Glides
3 3
1
4
2 2
55

PowerUp
Grommet
Worksurface
Shield
Installing Grommets & PowerUp
Hardware Parts List
(4)#20162 - #8 x 1/2” Screws
1. Press worksurface grommets into
wireway holes in worksurface.
PowerUp Only
2. Route cord through the hole in the
worksurface. Snap the PowerUp op-
tion into the hole in worksurface.
3. Install PowerUp shield to underside of
worksurface using (4) #8 x 1/2”
screws.
Attaching Bridge/Return to Corner
Unit
1. Slide Bridge/Return modesty panel
flange between corner unit end panel
and modesty panel. Fasten with
(3-4)* self drilling screws (Detail B).
Note: There are no pilot holes in the
corner unit modesty panel.
2. Place Bridge/Return on level
connector previously attached to
corner unit. Use (2) #14 x 7/8”
screws to attach.
3. Level Bridge/Return by adjusting hex
glides.
*(3) - 10-16 x 1/2” Self Drilling
Screws for partial modesty panel
(4) - 10-16 x 1/2” Self Drilling
Screws for full modesty panel
Desk Corner Unit
Bridge/Return
Detail B
Bridge/Return
Modesty Panel
Self Drilling
Screw
Corner Unit
Modesty Panel
CAUTION 21182-2 Jan. 1998
Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and
bolts must be tightened securely and must be checked periodically after assembly. Failure to assemble
properly, or to secure parts may result in assembly failure and injury.