KI Uniframe Conver User manual

Assembly Instructions
Uniframe
®
Conver

Uniframe® Convertible Bench
Assembly Instructions
1
8
8
4
Tools Required: 4mm Hex wrench,
3
/
8
” ratchet wrench,
7
/
16
” &
9
/
16
” sockets, adjustable wrench.
Support Leg Assembly
Right-hand
Qty. 1
Label on leg
L=Left- & R=Right-hand
Leg Assemblies
Top Assembly
Qty. 1
Bench Assembly
Qty. 1
Main Horizontal Tube
Qty. 1
Support Leg Assembly
Left-hand
Qty. 1
Item #1
SteelSpacer,.50” OD x .38” ID
Qty. 6
Item #2
Nut,
1
/
4
-20 NylonLock
Qty. 4 Item #3
Nut,
3
/
8
-16 Nylon Lock
Qty. 4 Item #4
Nut,
7
/
16
-14 Center Lock
Qty. 4
Item #5
Nut,
3
/ -16 UNC Acorn
Qty. 2
Item #6
Flat Washer,
1
/
4
” SAE
Qty. 4
Item#7
FlatWasher,
3
/
8
”SAE
Qty.12
Item #8
Flat Washer, ½” Nylon
Qty. 4
Item #9
HexBolt,
3
/-16x2” HHCS
Qty. 2
Item #10
SocketCapScrew,
1
/-20ButtonHead
Qty. 4

Uniframe® Convertible Bench
Assembly Instructions
2
1. Identifyright-&left-handsupportlegassembliesbylabelsonuppersupport
member (Figure 1 & Detail A).
2. Insert main horizontal tube through the pivot brackets in each bench assembly
(Figure 1).
3.
Insertfour
1
/
4
-20x2” screws(item10)intomainhorizontaltube(Figure1).
4. Placebenchassemblywithmaintubeontolegsaddles.
5.
Alignitem9screwswithholesandattachbenchassemblywith
1
/
4
”
flatwashers(item6)and
1
/
4
-20nylonlocknuts(item2)(Figure2&
Detail B).
Label on leg
Leg Assemblies
leg
item 10
Description
10

Uniframe® Convertible Bench
Assembly Instructions
3
8
3
match labels
legupright
label“R”
slotted angle
top assembly
apron assembly
label “R”
item 3
item 7
item 8
Detail C
item 7*
item 8*
item 1*
* Install items 7, 8 & 1 hardware on
bothlegsbeforeinstallingtopassembly
leg brace
bench leg
item 4
Figure 2 - Braces to Top, Legs & Bench Assembly
item 9
item 7
item 1*
item 7
item 5
Detail B
Bench Legs to Bench Brace
*Steelspacersallowthefastenerstotighten
without restricting movement at pivot points
1. Install leg braces tobench legs using hardware installedinsequenceshown
(Figure 2 & DetailB).
2.
Attopofleguprights,install
3
/
8
”flatwasher(item7),
1
/
2
”nylonwasher(item8)and
3
/
8
” steel spacer (item 1) onto leg bolts in sequence shown (Detail C).
3. Locate“L” and“R” labelsonapron assemblyundertop.
4. Install top assembly through slotted angle over the spacers onbolts
(Detail C).
5.
Install
1
/
2
”nylonwasher(item8),
3
/
8
”flatwasher(item7)and
3
/
8
-16
nylonlocknut(item3)ontoboltsandtighten(DetailC).
Description
Steel Spacer, .50” OD x .38”ID
8
3
Hex Bolt, / -16 x 2” HHCS
8
Flat Washer, ½” Nylon
3
Flat Washer, / ” SAE
8
Nut, 7/16 -14 Center Lock
3
Nut, / -16 Nylon Lock
Item
1
3
4
5
7
8
9
Nut, / -16 UNC Acorn

Uniframe® Convertible Bench
Assembly Instructions
movement at pivotpoints.
4
Detail D
Top Leg Brace to Apron
*Steel spacers allow the fasteners to tighten
withoutrestrictingmovementatpivotpoints
Figure 3 - Braces to Top at Apron Assembly
1. Attach
3
/
8
”flatwasher(item7)andsteelspacer(item1)ontobothapronboltsin
sequence shown (Figure 3 & Detail D).
2.
Rotate top assembly up (Figure 3).
3. Rotate both topsupport brackets upandlocate them onto the apron bolts. Spacers
go into the brace hole (Figure 3 & Detail D).
4. Install
3
/
8
”flatwasher(item7)and
3
/
8
-16nylonlocknut(item3)ontoapronbolts
and tighten (DetailD).
Note: Steel spacers allow the fasteners to tighten without restricting
locking
brace
/-16nut
brace
/-16nut
bolt
brace
item1*
item 3

Uniframe® Convertible Bench
Assembly Instructions
5
Note: Ifthetopsurfaceassemblyisnotleveloncethetopsupportbraceis
attachedtothe apron bolt, adjustments can be made atboth ends of the top
surface.The“apronbolt” issecuredatthefactoryintoaslottedholeinthe
“locking pivotanglebrace” and this slotallowsupto
5
/
8
”ofadjustment.
5.
Toadjusttheapronboltonthelockingpivotanglebrace,firstloosen the
outermosttopnutholdingthetopsupportbracetotheapronbolt(if installed
already in step 4). Next loosen the nut betweenthe top support brace and the
locking pivot angle brace by using two
9
/
16
”wrenches, one
betweenthebraces
andoneonthebolthead.Adjustthetabletolevel, thenre-tightenthenutand
theboltheadwhichpinchthelockingpivot angle brace only. Repeat
procedure at other endofbenchas necessary (Figure 3 & detailinset).

Uniframe® Convertible Bench
Assembly Instructions
movement at pivotpoints.
4

5
KI is a registered trademark
of Krueger International, Inc.
© 2016 Krueger International, Inc.
All Rights Reserved
Code KI-61586R10/KI/PDF/0616
Part # 13.7709