KI Aristotle Casegoods Wall-Mounted Overhead... User manual

Note: These instructions are for
attachment to conventional stud and
wallboard structures only, using the
Toggle Bolt Anchors supplied in the
hardware pack 7HP21.
Important: Refer to the “Required
Hardware” chart below for the minimum
number of bolts, and for the minimum
number of wall stud anchorages
required to support each size of
overhead. Always use more than the
minimum number of wall stud
anchorages if possible.
1. Carefully unpack all parts and place
overhead cabinet onto a soft,
protective surface. Identify parts
below from the “Hardware Packs”
diagram & Figure 1.
2. Remove lower mounting cleat from
rear of the overhead (Figure 1).
Retain shipping screws for further
use.
Assembly Instructions
Aristotle™ Casegoods
Wall-Mounted Overhead Cabinet
March 2008
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and injury.
1330 Bellevue Street • P. O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2008 KI All Rights Reserved • Litho in USA • Code KI-62012/HT/PDF/0308
Hardware Packs
Toggle
Bolt
#10 x 3”
Wood Stud
Screw
Toggle
Bolt Anchor 10
10
44
15
15
7HP21 - A - B
uppermounting
cleat
lowermounting
cleat
overhead cabinet
Figure 1
Overhead width 30" 36" 42" 48" 54" 60" 66" 72" 78"
Wall stud anchorages
required (minimum)
Mounting bolts
required (minimum)
Allowable load
(maximum - lbs.)
Hardware Pack 77HHPP2211--AA77HHPP2211--BB
Required Hardware
1 112 22 223
7 8 9 10 1213141515
300 360 420 480 540 600 660 720 780

3. Position lower mounting cleat on
the wall as shown (Figure 2),
ensuring that it is properly level.
Note: The bottom of the cleat is
approximately 113/4" above the
bottom of the overhead (Figure 2).
4. Using a 5/16" drill, drill through the
required number of pilot holes in
the lower mounting cleat to mark
the mounting bolt locations on the
wall (Figure 2).
5a. For wood-studded walls, open
up the 5/16" holes in the wallboard
to 1/2" diameter. When a wooden
stud is encountered, drill a new
1/8" hole into the stud from the par-
allel groove. Use a new #10 x 3”
wood screw to secure at this loca-
tion.
5b. For metal-studded walls, open
up the 5/16" holes in the wallboard
and any metal stud to 1/2" diameter.
6. Push one toggle bolt anchor into
each 1/2" diameter hole and secure
as per the Instructions for
SNAPTOGGLE®Toggle Bolts on
page 3. Installed anchor is shown
at “toggle bolt anchor installed”
(Figure 2).
7. Attach the lower mounting cleat to
the wall using the enclosed
mounting bolts (and wood screws
for wood studs).
8. Position the overhead cabinet on
the wall, ensuring complete
engagement of the upper mounting
cleat (attached to the back of the
overhead cabinet) onto the lower
mounting cleat (attached to the
wall).
9. Secure the overhead cabinet in
position using the shipping
screws, by screwing through the
pre-drilled holes in the back panel
and into the lower mounting cleat.
Assemble units as described herein only. To do otherwise may
result in instability. All screws, nuts and bolts must be tight-
ened securely and must be checked periodically after assem-
bly. Failure to assemble properly, or to secure parts may result
in assembly failure and injury.
Aristotle Casegoods™ Wall-Mounted Overhead Cabinet
Assembly Instructions
2
2shipping screwsre-used
asretaining screws
2holespre-drilled in back of
overhead forretaining screws
Vertical mounting surface
(shown as5/8” wallboard
- forreference only)
uppermounting cleat
toggle bolt
anchor
lowermounting
cleat
toggle bolt
anchorinstalled toggle
vertical
overhead cabinet
approximately113/4”
when installed
Figure 2

1. Drill 1/2" (13mm) hole. Hold metal
channel flat alongside plastic strap
and slide channel through hole
(Figure 3). Minimum clearance
behind wall should be 1 7/8"
(48mm).
2. Hold end of straps between thumb
and forefingers and pull toward
you until channel rests flush
behind wall. Slide plastic cap
along strap with other hand until
flange of cap is flush with wall.
Note: Do not stress or pull legs at
an angle to avoid premature
breakoff.
3. Snap straps at wall by pushing
side-to-side, snapping off straps
level with flange of cap.
4. Place item to be attached to wall
over flange. Insert bolt through
item and tighten until flush against
item, then stop. Use machine
screw or bolt to match thread
channel: bb 1/2" (20mm).
IMPORTANT: The plastic legs and cap
washers are positioning and position
retention elements only. They do not
otherwise function as anchoring
elements. Holding is dependent only
on a metal bolt to metal channel
connection. The TOGGLERS® brand
toggle bolt anchor complies with all
existing fire codes for critical
applications.
Assemble units as described herein only. To do otherwise may
result in instability. All screws, nuts and bolts must be tight-
ened securely and must be checked periodically after assem-
bly. Failure to assemble properly, or to secure parts may result
in assembly failure and injury.
Aristotle Casegoods™ Wall-Mounted Overhead Cabinet
SNAPTOGGLE®Toggle Bolts BB (1/2"-20) Instructions
3
Figure 1 Figure 2
Figure 3 Figure 4