KI Pirouette User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
Pirouette™Tables
Nesting-Base with Activ8®Electrical
August 2018 Tools Required
• Cordless Drill/Screwdriver
• #2 Phillips Driver Bit
• #3 Phillips Driver Bit
• 3/4” Open End Wrench
• 8mm Allen Wrench
Nesting Legs to Tabletop
Installation
1. Carefully remove contents from
shipping cartons and identify parts
and hardware supplied.
Note: The two nesting legs are
different, and are labeled so under
each nesting plate. An “L” or “R”
is displayed to represent left-or
right-hand. As labeled, the legs are
designed to install to a specific side of
the table support beam assembly. Take
care and follow directions below when
positioning legs for assembly. If legs
are not installed to the proper left- or
right-hand location, tables will not
nest properly and disassembly and
reassembly will be required.
2. Locate the nesting table support
beam assembly and position it so
the tabletop lock paddles face the
“user side” as illustrated. Choose
one nesting leg and identify if it is
right- or left-hand by the letter under
the pivot plate, then stand it upright.
Position the nesting leg such that the
pivot plate nests into the mounting
location in the beam assembly at the
correct left or right-hand location
as illustrated using an 8mm Allen
wrench. Twist in a M12 x 25mm flat
socket head screw through the top of
the nesting table support beam and
into the top of the nesting leg being
installed, but do not tighten at this
time. Repeat the process to loosely
attach the second leg to the support
beam. Once both legs are under the
support beam, use a 3/4” open end
wrench to hold (but do not turn)
the nut at the underside of each leg
upright. Using an 8mm Allen wrench
at the top, tighten the M12 x 25mm
flat head screw to secure. Do not turn
or tighten the nut at the bottom of
the nesting legs. Repeat the process
above to tighten the other leg to the
support beam at the top (Figures 1
& 2).
nesting table
support beam
M12 x 25mm
flat socket
head screw
nesting leg
(left)
nesting leg
(right)
Figure 1 - L
eg Installation
tabletop
lock paddle
pivot plate
(right)
pivot plate
(let)
tabletop
lock paddle
(face user side)
tabletop
lock paddle
(face user side)
USER
SIDE
RL
pivot plate
(left)
nesting leg
(left)
Figure 2 - Leg Installation Bottom View
nesting table
support beam
nesting leg
(right)
pivot plate
(right)

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Nesting Legs to Tabletop
Assembly Instructions
M5.5 x 42.2mm Phillips
flat head wood screw
nesting table
support beam
assembly
tabletop
Figure 3
table
support
end cap
tabletop
lock paddle
(face user side)
Detail A
tabletop lock paddle
(face user side)
tabletop
nesting leg
(right)
3. Place tabletop upside down on a
soft, protective surface. Position
the nesting table support beam
assembly onto the center of the
tabletop underside, making sure
that the tabletop lock paddles
on the support beam assembly
face the user side. Slide a table
support end cap into position at each
of the four locations on the support
beam and align the mounting holes in
the caps with the pre-drilled holes in
the table. Use a cordless drill with
a #3 Phillips bit to secure end caps
and table support to underside
of worksurface using two
M5.5 x 42.2mm Phillips flat head
wood screws at each cap location
(Figure 3 & Detail A).

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Nesting Legs to Tabletop
Installation (cont.)
4. Beam head covers are right- and
left-handed, so identify which
cover mates at each base/beam
location. Insert cover into place by
first inserting the inward facing tab
into the slot at the underside of the
nesting table beam support, then
rotate the beam head cover down and
align the two tabs with the mounting
holes in the base. Repeat the process
for the cover on the other base end.
At the side of the base opposite the
user side, using a cordless drill with
a #2 Phillips bit insert and tighten
a #8-32 x 1/2” thread forming screw
through the base and into the tab of
each beam head cover as illustrated.
Next, locate two nesting bumpers
and place a #8-32 x 1/2” screw
through each bumper, then insert and
tighten the screw into the user side
mounting hole, through the base and
into the mounting hole in the tab in
the beam head cover on both ends
of the base as illustrated (Figure 4 &
Detail B).
Important: For proper storing
and nesting of tables, the nesting
bumpers must be installed to
the user side, the side of the base
with the paddles.
5. Locking and non-locking casters
are provided. Locking casters are to
be installed to the front, user side
of each leg and non-locking casters
should be installed to the rear of
each leg. Use a 3/4” open end wrench
to tighten casters to the foot of each
leg (Figure 5).
6. To attach glides, thread stem into
bottom of leg by hand (Figure 5).
Figure 4
beam head
cover
beam head
cover
lock
paddle
nesting bumper
(face user side)
nesting table
support beam
#8-32 x /”
1
2
thread forming
screw
#8-32 x /”
1
2
thread for
ming
screw
#8-32 x /”
1
2
thread forming
screw
Figure 5
glide
caster
(locking)
caster
(non-locking)
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Nesting Legs to Tabletop
Assembly Instructions
Detail B
nesting bumper
(face user side)
#8-32 x /”
1
2
thread forming
screw
nesting leg
(right)
#8-32 x /”
1
2
thread forming
screw
Note: Nesting bumper must be assembled to
the user side for table to function properly.

4
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Velcro®Wire Managers & Villa Power Module
Assembly Instructions
Pirouette Table with Villa
Power Module for Activ8
The Activ8 electrical system is a UL
962 recognized component that allows
up to eight duplex power modules to
be connected to one standard 15-amp
power cord. The total length of the
Activ8 system and all interconnecting
cables (exclusive of the power infeed
unit) does not exceed 40 feet, or 12
meters.
Note: If tables are configured
table-to-table or back-to-back with
Activ8 electrical, tables must be
mechanically connected with gangers
or splice plates.
1. Position the Villa power module
for Activ8 on the underside of the
tabletop above the cutout. Orient the
notch in the module to face the user
side (Figure 7).
2. Align the six mounting holes on the
power module with the six pre-drilled
holes in the tabletop, then secure
the bracket to the underside of the
tabletop with the six #8 x 3/4” screws
provided (Figure 7).
Pirouette Table with Villa
Power Module Grommet
1. Position the Villa power module
grommet above the tabletop cutout
with the lid opening towards the user
(Detail C).
2. Push the grommet into the cutout,
tap lightly with a rubber mallet
if required, use caution to avoid
scratching the grommet (Detail C).
3. Secure the grommet to the tabletop
by inserting two #6 x 1/2” screws
through the holes on the inside of the
module into the cut edge of the top
(Detail C).
Velcro®Wire Managers
Installation
1. Position the two Velcro®wire
managers over the pre-drilled holes
in the underside of the tabletop
where illustrated. Locate and place
two steel position tabs, one at each
end over the mounting holes in the
wire manager, then secure using
four #10 x 5/8” screws, through the
two position tabs, wire manager
mounting holes and into the tabletop.
Do not over-tighten (Figure 6).
#10 x /”
5
8
screws
Velcro®
wire manager
steel
position tab
#10 x
/”
5
8
screws steel
position
tab
Velcro®
wire manager
Figure
6
Figure 7
Villa power module
for Activ8
#8 x /”
3
4
screws
tabletop
cutout
tabletop
Detail C
Villa power
module grommet
#6 x /”
1
2
screw
tabletop
cutout
tabletop
Villa power
module
for Activ8

5
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - PowerUp Module
Assembly Instructions
PowerUp module
for Activ8
tabletop
tabletop
cutout
Figure 8
Detail D
PowerUp module
for Activ8
snap
tabletop
cutout
tabletop
Detail E
Detail
F
ABCDE
Data Adapter Plates
Detail G
Blank Plate
Panduit “CJ”
Othonics “Trackjack”
AT&T
Panduit “KJ and KJA”, Amp CAT-3
and CAT-5, Hubble “Hd5”,
Ortronics “OR-6295003-T568B”
and “OR-6295004-T568A”
Krone, Leviton “41108-RE5”
A
B
C
D
E
Detail
H
Pirouette Table with PowerUp
Module for Activ8
The Activ8 electrical system is a UL
962 recognized component that allows
up to eight duplex power modules to
be connected to one standard 15-amp
power cord. The total length of the
Activ8 system and all interconnecting
cables (exclusive of the power infeed
unit) does not exceed 40 feet, or 12
meters. This section of the assembly
instruction describes the installation
of the Activ8 electrical system for two
tables.
Note: If tables are configured
table-to-table or back-to-back with
Activ8 electrical, tables must be
mechanically connected with gangers
or splice plates.
1. With the assembled table in the
upright position, orient the PowerUp
module for Activ8 as shown and
route the connector end down
through the grommet hole cutout in
the tabletop. Press the module down
firmly into the cutout to secure in
place, making sure the front and rear
snaps catch under the cutout bottom
edge of the tabletop (Figure 8 &
Detail D).
2. To open the PowerUp module, push
down lightly on the lid dimple and
release. To close module, push
lid down until slightly recessed in
module body and release. Open and
close the module to ensure smooth
operation (Details E & F).
3. Select the appropriate data adapter
plate for the phone/data jack to be
used and carefully remove from
injection molded tree (Detail G).
Note: Jacks are sold by separate
companies and are not supplied with
the module.
4. Wire the jack appropriately to the
data plate and snap the data plate
assembly into the module grommet
opening as shown (Detail H).
Note: Depending on style of data
jack used, it may be necessary to
route the phone/data cord through
the module grommet opening and
data plate to install. Each installation
may vary.
5. The PowerUp module may be
removed without tools by squeezing
the front and rear snaps located on
the module under the tabletop while
pushing up the module (Figure 8).

6
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Infeed & RPT Modules Installation with No Power Module
Assembly Instructions
Activ8 Infeed & RPT Modules
Installation with No Power Module
1. With the assembled table in the
upright position, place the flip-top
grommet above the tabletop cutout
with the lid opening towards the user
(Detail I).
2. Push the grommet into the cutout,
tap lightly with a rubber mallet
if required, use caution to avoid
scratching the grommet (Detail I).
3. If flip-top grommet was installed,
make sure the cover is closed, then
carefully rotate the table to be upside
down on a soft, protective surface.
4. Position the wire trough with the
open-side face up, onto the floor
along the back side of the table as
illustrated. Face the wire trough’s
RPT module mounting holes of the
wire trough to the back edge of the
table to make rotating into position
easier once other components have
been installed (Figure 9).
Note: RPT modules for Activ8 can
be used in conjunction with modesty
panels, however, the trough will need
to be turned 180 degrees, so the RPT
modules face the user once installed
(Detail J & Figure 16).
5. To install the RPT module for
Activ8 into the wire trough, first
route the connector end in through
the rectangular-shaped module
mounting hole as illustrated, routing
the connector ends toward the
middle of the trough, then snap the
module receptacles into position
(Figure 9).
Figure 9
wire
trough
RPT module
for Activ8
connector
end
connector
end
Detail I
flip-top
grommet
snap
tabletop
cutout
tabletop
RPT module
for Activ8
Detail J - RPT Module/Trough with Modesty Panel
wire
trough
RPT module
for Activ8
RPT module
for Activ8

7
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Infeed & RPT Modules Installation with No Power Module
Assembly Instructions
Figure 11
#14- /”
3
4
self-tapping
screws
wire
trough Velcro®
wire manager
Velcro wire
®
manager
Activ8
power
infeed
Activ8 table-to-table
jumper
6. Locate the Activ8 power infeed/
smart box unit and snap the
connector end of the power infeed
into one socket of the RPT module
for Activ8, then set the power infeed
smart box into the wire trough
(Figure 10).
7. For this step, first locate one Activ8
jumper. Connect the Activ8 jumper
to the other open socket on the RPT
module, and to the RPT module for
Activ8 at the other end (Figure 10).
8. Locate the Activ8 table-to-table
jumper cable and connect one
end to the remaining RPT module
connection, then route the
remaining cable and connector
end out of the wire trough end
(Figure 10).
9. With all connectors plugged in,
locate the fuse access on the smart
box of the Activ8 Power infeed,
and position the fuse location to
be accessible through the large
rectangular cut-out in the wire
trough side (Figure 10).
10. Holding contents inside the wire
trough, carefully turn it over,
upside-down onto the tabletop, and
over the tabletop cutout. Adjust the
power infeed, the connectors and
cables in the trough so the trough
lays flat. Align the wire trough
mounting holes with the pre-drilled
holes in the underside of the
tabletop, and secure wire trough to
tabletop using six #14 x 3/4”
self-tapping screws. Do not
over-tighten (Figure 11).
11. Use the Velcro®wire managers at
each end to strap the Activ8 power
infeed cable and the table-to-table
jumper to the underside of the table
(Figure 11). Carefully turn table to
the upright position.
Figure 10
Activ8 power
infeed/smart
box
Activ8
jumper
Activ8
table-to-table
jumper
wire
trough
RPT module
for Activ8
tabletop
cutout

8
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Infeed & RPT Modules Installation with Power Module
Assembly Instructions
Figure 12
wire
trough
RPT module
for Activ8
connector
end
connector
end
RPT module
for Activ8
power module for Activ8
(PowerUp shown)
Detail K - RPT Module/Trough with Modesty Panel
wire
trough
RPT module
for Activ8
RPT module
for Activ8
power module
for Activ8
(PowerUp shown)
Activ8 Infeed & RPT Modules
Installation with Power Module
1. If PowerUp module for Activ8 was
installed, make sure the cover is
closed, then carefully rotate the
table to be upside down on a soft,
protective surface.
2. Position the wire trough with the
open-side face up, onto the floor
along the back side of the table as
illustrated. Face the wire trough’s
RPT module mounting holes to
the back edge of the table to make
rotating into position easier once
other components have been
installed (Figure 12).
Note: RPT modules for Activ8 can
be used in conjunction with modesty
panels, however, the trough will need
to be turned 180 degrees, so the RPT
modules face the user once installed
(Detail K & Figure 16).
3. To install the RPT module for
Activ8 into the wire trough, first
route the connector end in through
the rectangular-shaped module
mounting hole as illustrated, routing
the connector ends toward the
middle of the trough, then snap the
module receptacles into position
(Figure 12).

9
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Infeed & RPT Modules Installation with Power Module
Assembly Instructions
Figure 14
#14- /”
3
4
self-tapping
screws
wire
trough Velcro®
wire manager
Velcro wire
®
manager
Activ8
power
infeed
Activ8 table-to-table
jumper
4. Locate the Activ8 power infeed/smart
box unit and snap the connector end
of the power infeed into one socket of
the PowerUp module for Activ8, then
set the power infeed smart box into
the wire trough (Figure 13).
5. For this step, first locate two Activ8
jumpers. Connect the first Activ8
jumper to the PowerUp module at
one end, and to the closest RPT
module for Activ8 at the other end.
Connect the second Activ8 jumper
into the connector ends of both RPT
modules installed in the wire trough
(Figure 13).
6. Locate the Activ8 table-to-table
jumper cable and connect one
end to the remaining RPT module
connection, then route the remaining
cable and connector end out of the
wire trough end (Figure 13).
7. With all connectors plugged in,
locate the fuse access on the smart
box of the Activ8 Power infeed,
and position the fuse location to
be accessible through the large
rectangular cut-out in the wire trough
side (Figure 13).
8. Holding contents inside the wire
trough, carefully turn it over
180-degrees, (upside-down) onto the
tabletop, and over the power module
for Activ8. Adjust the power infeed,
the connectors and cables in the
trough so the trough lays flat. Align
the wire trough mounting holes with
the pre-drilled holes in the underside
of the tabletop, and secure wire
trough to tabletop using six
#14 x 3/4” self-tapping screws.
Do not over-tighten (Figure 14).
9. Use the Velcro®wire managers at
each end to strap the Activ8 power
infeed cable and the table-to-table
jumper to the underside of the table
(Figure 14). Carefully turn table to
the upright position.
Figure 13
Activ8 power
infeed/smart
box
Activ8
jumpers
Activ8
table-to-table
jumper
wire
trough
RPT module
for Activ8
power module for Activ8
(PowerUp for Activ8 shown)

10
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Vertical Wire Manager
Assembly Instructions
Vertical Wire Manager
Installation
1. To install vertical wire manager, route
the power cord along the leg, then
snap the wire manager to the post
with the cord in between. Vertical
wire manager easily snaps on and off
the leg, to add or reconfigure cords
(Figure 15).
Figure 15
power
cord
tabletop
vertical
wire manager

11
Modesty Panels Installation
Note: 18” to 24” deep tables may
have modesty panels installed to
them, but 30”-36” deep tables do not
allow that option.
Note: RPT modules for Activ8 can
be used in conjunction with modesty
panels, however, the trough will need
to be turned 180 degrees so the RPT
modules face the user once installed
(Figure 16, Detail J & K).
1. With table upside down on a soft,
protective surface, position the
modesty panel down near the back
edge of the tabletop where it will
install. The wire manager on the
modesty panel should face up, and
the notches exposing the pivot rod in
the panel should face the back edge
of the table as illustrated (Figure 16).
2. Locate the mounting clips and
position them over the weld bump on
the pivot rod as illustrated. The tabs
with the mounting holes must face
the modesty panel, or disassembly
and reassembly will be required
(Figure 16 & Detail L).
3. Move the modesty panel with clips
up to align the mounting holes of the
clips with the pre-drilled holes in the
table. The mounting holes will be
close to the edge. Screw each clamp
to the underside of the table with a
#10 x 3/4” wood screw per clamp as
illustrated (Figure 16 & Detail L).
Note: Pirouette Tables less than 72”
in length will use two clamps per
modesty panel, but 72” long tables
will use three clamps to the tabletop.
Figure 16
Detail L
#10 x /”
3
4
screw
weld
bump
mounting
hole
clip
pivot
rod
wire
manager
modesty
panel
#10 x /”
3
4
screw
clip
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Modesty Panel
Assembly Instructions

12
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Pirouette Tables™ Nesting-Base with Activ8®Electrical - 24”, 30” & 36” Table-to-Table Ganging
Assembly Instructions
CAUTION: If Channels (Wire Troughs)
are used they are not to be used for routing
extension cords. Power supply cords are
not to be routed across or through more
than one complete unit/tabletop.
WARNING: Assembly of all table
components must be completed before
making any electrical connections. All
electrically connected furnishings must
also be mechanically connected.
Table-to-Table Ganging, 24”, 30”
& 36” Pirouette Nesting-Base
Tables
Note: Take note of correct ganging
hook and peg mounting locations to
assure proper latching for each type
of installation. The instructions on
this page detail ganging of 24”, 30”
& 36” deep nesting-base tables
table-to-table.
1. Carefully turn tables to the upright
position. On every corner of the first
table, install a peg using a
#14 x 11/2” wood screw. As
illustrated, and based on the table
depth, install two hooks to the first
table using two pegs for table-to-table
ganging of two tables. Next, install
four pegs at the other illustrated
locations on the first table for future
use to store ganging hooks
(Figure 17).
2. At the second table, on every corner
of the table, install a peg using a
#14 x 11/2” wood screw. Install two
hooks on the second set of pegs
inline with the first set of pegs with
installed ganging hooks. Next, install
four pegs at the other illustrated
locations on the second table for
future use to store ganging hooks
(Figure 17).
3. Move tables together and swing the
ganging hooks of the first table to
securely engage the pegs under the
second table (Figures 17 & 18).
Figure 17 - 24”, 30” & 36” Nesting-Base Tables with Table-to-Table Ganging
first table
ganging
hook
peg
pegs
(for storage)
peg
peg
#14 x 1 /”
1
2
wood screw
ganging
hook
second table
peg
#14 x 1 /”
1
2
wood screw
pegs
(for storage)
Activ8
table-to-table
jumper
Figure 18 - 24”, 30” & 36” Nesting-Base Tables with Table-to-Table Ganging
pegs
(for storage)
Activ8
table-to-table
jumper
ganging
hook
pegs
(for storage)

13
Back-to-Back Ganging, Pirouette
Nesting-Base Tables
Note: Take note of the correct
orientation of ganging hooks and peg
mounting locations to assure proper
latching for back-to-back ganging
(Figure 19).
1. Carefully turn tables to the upright
position. On every corner of the first
table, install a peg using a
#14 x 11/2” wood screw. As
illustrated, and based on the table
depth, install two hooks to the first
table using two pegs for back-to-back
ganging of two tables. Next, install
four pegs at the other illustrated
locations on the first table for future
use to store ganging hooks
(Figure 19).
2. At the second table, on every corner
of the table, install a peg using a
#14 x 11/2” wood screw. Install two
hooks on the second set of pegs
inline with the first set of pegs with
installed ganging hooks. Next, install
four pegs at the other illustrated
locations on the second table for
future use to store ganging hooks
(Figure 19).
3. Move tables together and swing the
ganging hooks of the first table to
securely engage the pegs under the
second table (Figure 19).
Figure 19 - Nesting-Base Tables with Back-to-Back Ganging
peg
ganging hook
(engaged)
peg
(for storage)
first table
second table
#14 x 1 /”
1
2
wood screw peg
(for storage)
Activ8
back-to-back
jumper
ganging
hook
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Back-to-Back Ganging
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
CAUTION: If Channels (Wire Troughs)
are used they are not to be used for routing
extension cords. Power supply cords are
not to be routed across or through more
than one complete unit/tabletop.
WARNING: Assembly of all table
components must be completed before
making any electrical connections. All
electrically connected furnishings must
also be mechanically connected.

14
Pirouette Tables™ Nesting-Base with Activ8®Electrical - Connections with Source Power
Assembly Instructions
Pirouette Nesting-Base Tables -
Activ8 Connections with Source
Power
Warning: Never attach more than
one power infeed to a chain of
devices. Always check to be certain
that the system is not already
powered from another source before
attaching an infeed.
1. Place tables in final location and lock
the two front, user side casters in
place on each table. Snap the
table-to-table and/or back-to-back
jumper ends into each table’s power
module for Activ8. Be sure the clip
engages on each jumper for a secure
fit (Figure 20).
2. Plug the power infeed connector
end into an appropriate location in
the Activ8 system only after all other
components are installed and check
the LED light. Verify that a green LED
is lit on the power infeed enclosure.
A green LED indicates that power
is being supplied to the devices. If
the LED is flashing red, verify that
no other infeeds are attached to the
system. If the LED is solid red, verify
that there are no more than eight
devices plugged together, and that
the total length of the system and all
interconnecting cables (exclusive
of the power infeed unit) does not
exceed 40 feet, or 12 meters.
3. When tables are un-ganged, on the
back user side, detach the ganging
hook and snap both ends to the two
installed pegs for storage near the
center of the tabletop.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
This product is for use on a nominal 120-volt circuit and has a grounding plug
that looks like the plug illustrated in Detail M. Make sure that the product is
connected to an outlet having the same configuration as the plug. No adapter
should be used with this product.
GROUNDING INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be
followed, including the following:
Read all instructions before using (this furnishing).
DANGER: To reduce the risk of electric shock:
1. Always unplug this furnishing from the outlet before cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to
persons:
1. Unplug from outlet before putting on or taking parts off parts.
2. Close supervision is necessary when this furnishing is used by, or near
children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these
instructions. Do not use attachments not recommended by the manufacturer.
4. Do not use outdoors.
5. WARNING: Risk of Electric Shock-Connect this furnishing to a properly
grounded outlet only. See Grounding Instructions.
SAVE THESE INSTRUCTIONS
Electrical Rating: 120V 12 A
WARNING: Risk of Injury-Maximum Load 4.7 lbs. per inch width.
power module for Activ8
(PowerUp shown)
Activ8 power
infeed/smart
box
Activ8
back-to-back
jumper
RPT module
for Activ8
RPT module
for Activ8
RPT module
for Activ8
Activ8
jumper
Activ8
jumper
end
Figure 20 Detail M
grounding
pin
grounded
outlet
locking
caster
locking
caster
locking
caster

15
Pirouette Tables™ Nesting-Base with Activ8®Electrical
Assembly Instructions

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2018 Krueger International, Inc. All Rights Reserved • Code KI-AI-000015R1/KI/PDF/0818
Pirouette Tables™ Nesting-Base with Activ8®Electrical
Assembly Instructions