KI Barron Table User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
Barron® & Portico™Tables
Fixed Base
Lightweight and Short Fold T-Base
Flip-Top
August 2016
Fixed Base Table
Tools Required
• Phillips Screwdriver
Hardware Included for T-Base
• (8) #14 x 1” Wood Screws
Hardware Included for X-Base
• (4) #14 x 1” Wood Screws
1. Position base assembly on underside
of table top (Figure 1).
2. Secure with Phillips head screws
in the following “X” pattern, not to
exceed 60 in/lbs of torque
(Figure 2).
1
2
3
4
3. Regularly check screws to be sure
they remain snug.
Figure 1
Figure 2

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Lightweight and Short Fold T-Base Folding Table
Assembly Instructions
Lightweight and Short Fold T-Base
Folding Table
Tools Required
• Phillips Screwdriver
Hardware Included for T-Base
• (8) #14 x 1” Wood Screws
Note: The instructions below
illustrate the assembly of both the
lightweight folding T-base (Figure 3)
and the short fold T-base (Figure 4).
The item that is required to make the
base a short fold base is the short
fold adapter plate (Figure 4). It is
only on one T-base of each pair. The
adapter plate allows the folded leg to
be clamped shut while overlapping
the opposite T-leg.
1. Place the table top upside down onto
a soft protective surface
(Figures 3 & 4).
2. Locate the four pre-drilled holes
at each end of the table. Align
the holes of each T-base with the
pre-drilled holes in the table. The
folded legs of the T-bases must be
positioned toward the center of the
table (Figures 3 & 4). If installation
requires a short fold base (Figure 4),
the short fold leg must be positioned
over the standard leg.
3. Secure bases to the table with four
#14 x 1” wood screws provided,
not to exceed 60 in/lbs of torque
(Figures 3 & 4).
standard
T-base
leveling
glide
#14 x 1”
screw standard
T-base
table top
Figure 3 - Lightweight Folding T-Base
standard
T-base
leveling
glide
table top
short-fold
T-base
#14 x 1”
screw
short-fold
adapter plate
Figure 4 - Short Fold T-Base

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Lightweight and Short Fold T-Base Folding Table
Assembly Instructions
Lightweight and Short Fold
T-Base Folding Table Operation
To UnFold Table
1. Place table top upside down onto a
soft protective surface (Figure 5).
2. Unsnap table leg from leg holder.
Lift leg to a 90° angle making sure
the base locks securely into place
(Figure 5).
3. Repeat step 2 for other leg.
To Fold Table
4. Place table top upside down onto a
soft protective surface (Figure 5).
5. While depressing either one or both
of the gray release levers on either
side of the leg base, push the leg
down toward the center of the table.
Snap the leg into the plastic leg
holder (Figure 5).
6. Repeat step 5 for other leg.
7. If all four glides do not come
in contact with the floor, adjust
appropriate glide(s) in or out to
stabilize table (Figure 5).
8. While in the folded position, the
spacing bumpers provide protection
for the top surface of an adjacent
table when tables are leaned against
each other (Figure 5).
Caution: The spacing bumpers
should not be used to stack tables
flat on the floor. Tables are unstable
when stacked in this manner and
could result in personal injury and/or
product damage.
Figure 5 - Lightweight Folding T-Base
release
lever
leg
holder
leg
holder

4
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Flip-Top Table
Assembly Instructions
Flip-Top Table Assembly
Tools Required
• Phillips Screwdriver
Hardware Included for
Flip-Top T-Base
• (12) #14 x 1” Wood Screws
Hardware Included for
Flip-Top X-Base
• (6) #14 x 1” Wood Screws
1. To avoid scratching the table
top, place face down onto a soft
protective surface (Figure 6).
2. Position base assembly on underside
of table top, aligning holes in base
assembly with pre-drilled holes in
table top. Attach using the six
#14 x 1” screws, not to exceed
60 in/lbs of torque. Close flip-top
mechanism by pulling base to a
vertical position. Base is secure
when mechanism “clicks”. Stand
table upright (Figure 6).
Flip-Top Table Operation
For Use
1. Pull top down until mechanism
“clicks” shut (Figure 7).
Figure 6 - Flip-Top Table
flip-top
X-base
#14 x 1”
wood screw
Figure 7
release
tab
For Storage
1. Push down on release tab and lift up
on table top (Figure 7).
Note: refer to page 7,
Figures 10 & 11 for more
information on flip-top table
operating instructions.

5
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Double Flip-Top Table
Assembly Instructions
Double Flip-Top Table Assembly
Tools Required
• Phillips Screwdriver
• 3/16” hex wrench (Allen wrench)
• 3/8” wrench
• 7/16” wrench
Hardware
• Twelve #14 x 1” screws
• Four 1/4-20 x 1/2” Socket Head Cap
Screws with patch
• Four 1/4-20 Nuts
• Two #10-32 x 1/2” Phillip Head
Pan Heads Screws with locking
washer
• Two #10-32 Cap Nuts
Base Installation
1. Unpack table bases and table top.
2. To avoid scratching the table top,
place it finish side down on a soft
protective material.
3. Unlock and open flip base
mechanisms, position base
assemblies on underside of table top,
aligning holes in base assemblies
with pre-drilled holes in table top.
Attach each base to the top using
four #14 x 1” screws in the four front
holes (Figure 8 & Detail A).
4. Close flip-top mechanisms by
pulling base to a vertical position.
Bases are secure when lock level
engages rod (Detail B).
5. Finally, insert and tighten two
#14 x 1” screws to the back of bases,
Insert glides into base feet and stand
table upright (Figure 8).
Note: Two people are required to
turn table to the up-right position.
Figure 8 - Double Flip-Top Table
#14 x 1”
screw
lock
lever
flip base
mechanism
rod
lock lever
rod
Detail A
lock
lever
rod
Detail B
glide

6
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Double Flip-Top Table
Assembly Instructions
Cross Tube Assembly
6. With table upright, disengage flip
mechanisms and flip table top up
until it stops (Figure 9).
7. Position cross tube under the
opened table bases as illustrated.
The large holes in the cross tube
should face the floor. Using a 3/16”
hex wrench (Allen wrench) insert
1/4-20 x ½” cap screw into the
large hole in the cross tube, align
and insert the screw in a hole in
the flip base lower plate. From the
top, attach 1/4-20 cap screw to the
nut and screw finger tight to hold
it to plate. Install other screws and
nuts to cross tube and base plates.
Tighten hardware securely
(Detail D).
Handle To Lock Levers Assembly
Note: Without handle installed it
will take two people to flip table
open.
8. Position a handle over the lock
levers as illustrated, with the rib
side up. Insert a #10-32 screw with
washer into a hole in the handle
and through the bottom hole in a
base lock lever. Attach a #10-32 nut
to the screw finger tight. Insert the
other screw with washer through
the other handle hole and bottom
base lever hole and attach nut.
Using a Phillips screwdriver and
3/8” wrench tighten screws and nuts
securely (Detail C).
9. Grasp table top firmly and lower
into place, press down on top to
lock it into place.
10. Lift up slightly on front edge of
top to ensure it is locked in place.
Apply more downward pressure if it
is not engaged.
11. Table should lock and unlock
easily. Loosening and
re-adjusting the cross tube and
handle may be required to obtain a
smooth operation (Detail D).
handle
cross
tube
#10-32
screw with
washer
lock
lever
#10-32
nut
Detail C
Detail DFigure 9
11
/ -20 x /”
42
cap screws
1/ -20 nuts
4

7
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Barron®& Portico™ - Double Flip-Top Table
Assembly Instructions
Operating Instructions
For Storage
1. To rotate into storage position push
down on the handle and lift top up
until it stops (Figure 10).
For Use
1. Grasp table top firmly, lower into
place and press down on front
edge to lock the table top into place
(Figure 11).
2. Lift up slightly on front edge of top
to ensure it is locked in place. Apply
more down ward pressure if it is not
engaged (Figure 11).
push down on
handle first
lock
Figure 10
pull up
on top
Figure 11
grasp top firmly
and rotate down
push down on top to actuate lock,
pull up slightly on top to ensure
that lock has engaged
lock

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2016 Krueger International, Inc. All Rights Reserved • Code KI-61574R7/KI/PDF/0816