KI 700 Series User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Required
• Cordless Power Drill
• 1/4” Drill Bit & #3 Phillips Bit
Optional Laminate Top Assembly
Note: It is recommended that all
laminate tops be secured to storage
unit(s) from the underside with
fasteners through drilled holes
(2” from the edge at each corner), in
addition to securing with double-
sided tape (fasteners and tape
provided) (Figures 1 & 4). It is
required that laminate tops larger
than 42” long and/or having a
depth of 18” or greater, be secured
to storage unit(s) at the corners
as illustrated, plus two additional
“on-center” mounting locations. One
rear on-center location should be
2” from the storage unit back edge
and another must be 5” back from
the front edge, and on-center as
illustrated (Details A & C).
1. Position, level and gang storage
unit(s) together (if applicable) at their
final installation location. If casters
are assembled to the storage units,
engage the locks on the casters to
prevent the units from moving.
2. Clean the top of storage unit(s), at
each corner with warm water and mild
detergent, then rinse and wipe dry.
3. Use a tape measure and pencil
to locate and mark four pilot hole
locations to the top of the storage
unit. As illustrated, each marked
location should be near each corner
and be 2” in from the front/back and
right/left-hand sides, at the top of the
storage unit (Figure 1).
4. To gain access for drilling and to
install fasteners, remove the top two
drawers from the storage units where
applicable (Figure 2).
5. From the top of the unit, drill a 1/4”
diameter hole at each marked corner,
and at the on-center front and back
location if applicable (Detail A).
When all appropriate mounting holes
have been drilled, remove debris
from storage unit(s) (Figure 3).
Note: For laminate tops larger
than 42” long or having a depth of
18” or greater, two or more people
are required to correctly align and
position the top onto the storage
unit(s). For any size laminate top,
ensure top is positioned correctly
before setting on tape as it will be
difficult to move afterward.
Assembly Instructions
Optional Laminate Top
700 Series, Connection Zone Collection & U-Series
December 2019
Figure
1
storage
unit (top)
marked
pilot hole
location
2”
2”
2”
2”
Figure
2
storage
unit (top)
Figure
3
storage
unit (top)
cordless
power drill
marked
pilot hole
locations
Detail A - Storage Units with L
aminated Tops
42” and Wider or 18” and Deeper
2” 2”
2” 2”
2”
5”
marked
pilot hole
location
storage
unit (top)

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2019 Krueger International, Inc. All Rights Reserved • Code KI-AI-000059/KI/PDF/1219
700 Series, Connection Zone Collection & U-Series - Optional Laminate Worksurface
Assembly Instructions
Optional Laminate Top
Assembly (cont.)
6. Apply 3” long strips of
double-sided tape to top corners
of the storage unit, about 1/4”
from the edges of the front and
back of each side as illustrated
(Figure 4 & Detail B).
7. Remove the backing from the
double-sided tape, which were
adhered to the storage unit tops
in the previous step. Carefully
center the laminate top over the
storage unit(s) such that the top
overhangs the storage unit by
1/16” on all sides, then set the
laminate top onto the storage
unit(s) (Figure 5).
Note: For the step below, it is
advised to either have a second
person press down on the
laminate top while driving in
each screw, or pre-drill each hole
using a 7/64” drill bit to no deeper
than 1/2” before driving in screws.
8. Assure that the laminate top is
properly aligned on the storage
unit(s). Then, from inside the
storage unit(s) at the pre-drilled
holes, use a power drill with #3
Phillips tip and #14 x 7/8” Phillips
Pan Head screws to secure the
storage unit top(s) to the laminate
top at each corner, and at the
on-center front and back
locations, if applicable
(Figure 5 & Detail C).
9. Re-install the drawers if removed
in step 4.
laminate
worksurface
cordless
power drill
#14 x /”
phillips pan-head
screw
7
8
Figure
6
storage
unit (top)
1/”
4
1/”
4
1/”
4
1/”
4
Detail B
double-sided
tape
1/”
4
Figure
4
Figure 5
laminate
worksurface
storage
unit (top)
Detail C - Storage Units with Laminated Tops
42” and Wider or 18” and Deeper
#14 x /”
phillips pan-head
screw
7
8
cordless
power
drill
laminate
worksurface