Kimball Office Dock User manual

Dock™1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Fixed Resin Modesty Panel to
Worksurface Assembly
Tools Required
 Cordless driver with magnetic post
 1/8” Drill Bit
 4mm Allen Wrench drive
 #3 Phillips head bit drive
Hardware Required (Included)
Modesty Sizes 24”
48”
60”
72”
84”
96”
L Bracket 234
Modesty Cover Plate 234
1/4-20 X 1/2” BHMS 468
#10 X 1” FBSCR 468
Figure A
COVER PLATE
L BRACKET
Figure B
Installation
Note: Modesty Panel should be installed after bases.
1. Unpack modesty panel, L bracket, modesty cover plate,
and hardware. See Figure A for package contents.
2. Place modesty cover plate over outside pre-drilled holes of
modesty panel and L bracket over inside holes of the mod-
esty panel as shown in Figure B. Assemble with 1/4-20 X
1/2” BHMS using 4mm hex drive.
3. Place the worksurface up side down on a non-marring sur-
face.
4. Using a tape measure, position the modesty panel from the
approach side of the worksurface 1” in and predrill using
1/8” bit.
5. Assemble with #10 X 1” FBSCR wood screws using #3
Phillips bit drive. as shown in Figure C. Flip the worksur-
face back over onto the bases.
Figure C
1"

Dock™2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Fixed Wood Modesty Panel to
Worksurface Assembly
Tools Required
 Cordless driver with magnetic post
 #2 Phillips Head Bit Drive
 #3 Phillips Head Bit Drive
Hardware Required (Included)
Modesty Sizes 24”
48”
60”
72”
84”
96”
L Bracket 234
#12 x 5/8” FBSCR 468
#10 x 1” FBSCR 468
Installation
1. Unpack modesty panel, L bracket, and hardware. See Fig-
ure A for package contents.
2. Place L bracket over pre-drilled holes and assemble with
#12 X 5/8” wood screws using #2 Phillips head drive. See
Figure B.
3. Place the worksurface up side down on a non-marring sur-
face.
4. Using a tape measure, position the modesty panel from the
approach side of the worksurface 1” in and predrill using
1/8” bit.
5. Assemble with #10 X 1” FBSCR wood screws using #3
Phillips bit drive. as shown in Figure C. Flip the worksur-
face back over onto the bases.
Figure A
L BRACKET
Figure B
Figure C
1"

Dock™3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Removable Resin Modesty
Panel to Worksurface Assembly
 Cordless driver with magnetic post
 4mm hex drive
 #3 Phillips head bit drive
Tools Required
Hardware Required (Included)
Modesty Sizes 24”
48”
60”
72”
84”
96”
L Bracket 234
Modesty Cover Plate 234
Removable Bracket 234
1/4-20 THM SCR 234
1/4-20 X 1/2” BHMS 468
#10 X 1” FBSCR 468
Installation
1. Unpack modesty panel, L bracket, modesty cover plate,
removable bracket, and hardware. See Figure A for pack-
age contents.
2. Place modesty cover plate over outside pre-drilled holes of
modesty panel and L bracket over inside holes of the mod-
esty panel as shown in Figure B. Assemble with 1/4-20 X
1/2” BHMS using 4mm hex drive.
3. Place the worksurface up side down on a non-marring sur-
face.
4. Using a tape measure, position the modesty panel on the
approach side (non user side) of the worksurface 1” in and
pre-drill holes as shown in figure C.
5. Place removable bracket over the L bracket and assemble
worksurface with #10 X 1” FBSCR using #3 Phillips head
bit drive as referenced in figure B. Flip the worksurface
back over onto the bases.
Figure A
COVER PLATE
L BRACKET
REMOVABLE
BRACKET
Figure B
Figure C
1"

Dock™4
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Removable Wood Modesty
Panel to Worksurface Assembly
Tools Required
 Cordless driver with magnetic post
 #2 Phillips head bit drive
 #3 Phillips head bit drive
Hardware Required (Included)
Modesty Sizes 24”
48”
60”
72”
84”
96”
L Bracket 234
Removable Bracket 234
1/4-20 THM SCR 234
1/4-20 X 1/2” BHMS 468
#10 X 1” FBSCR 468
Installation
1. Unpack modesty panel, L bracket, removable bracket and
hardware. See Figure A for package contents.
2. Place L bracket over pre-drilled holes and assemble with
#12 X 5/8” wood screws using #2 Phillips head drive as
shown in Figure B.
3. Place the worksurface up side down on a non-marring sur-
face.
4. Using a tape measure, position the modesty panel from the
approach side (non user side) of the worksurface 1” in and
predrill as shown in figure C.
5. Place removable bracket over the L bracket and assemble
worksurface through pre-drilled holes with #10 X 1”
FBSCR using #3 Phillips head bit drive as referenced in
figure B. Flip the worksurface back over onto the bases.
Figure A
L BRACKET
REMOVABLE
BRACKET
Figure B
Figure C
1"

Dock™5
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Figure A
Flip/Nest Resin Modesty Panel
to Worksurface Assembly
Tools Required
Hardware Required (Included)
 Cordless driver with magnetic post
 4mm hex drive
 #3 Phillips head bit drive
1. Unpack modesty panel, magnetic hinge, modesty cover
plate, and hardware. See Figure A for package contents.
2. Place modesty cover plate over outside pre-drilled holes of
modesty panel and magnetic hinge over inside holes of the
modesty panel as shown in Figure B. Assemble with 1/4-
20 X 1/2” BHMS using 4mm hex drive.
3. Place the worksurface up side down on a non-marring sur-
face.
4. Using a tape measure, position the modesty panel on the
approach side (non user side) of the worksurface 1” in and
predrill.
5. Assemble with #10 X 1” FBSCR wood screws using #3
Phillips bit drive. as shown in Figure C. Flip the worksur-
face back over onto the bases.
Installation
Modesty Sizes 24”
48”
60”
72”
84”
96”
Magnetic Hinge 234
Modesty Cover Plate 234
1/4-20 X 1/2” BHMS 468
#10 X 1” FBSCR 468
Figure C
Figure B
COVER PLATE
MAGNETIC
HINGE
COVER
PLATE
MAGNETIC
HINGE
1"
Tools Required

Dock™6
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2700494 Revision -
Assembly Instructions
Figure A
Flip/Nest Wood Modesty Panel
to Worksurface Assembly
Tools Required
Hardware Required (Included)
 Cordless driver with magnetic post
 #2 Phillips head bit drive
 #3 Phillips head bit drive
1. Unpack modesty panel and hardware. See Figure A for
package contents.
2. Place the worksurface up side down on a non-marring sur-
face.
3. Attach magnetic hinge to modesty panel with #12 X 5/8”
wood screws using #2 Phillips head bit drive.
4. Using a tape measure, position the modesty panel from the
approach side (non user side) of the worksurface 1” in and
predrill as shown in figure C.
5. Place removable bracket over the L bracket and assemble
worksurface through pre-drilled holes with #10 X 1”
FBSCR using #3 Phillips head bit drive as referenced in
figure B. Flip the worksurface back over onto the bases.
Installation
Modesty Sizes 24”
48”
60”
72”
84”
96”
Magnetic Hinge 234
#12 X 5/8” FBSCR 468
#10 X 1” FBSCR 468
Figure B
MAGNETIC
HINGE
1"
Figure C