Kimball Office President User manual

Casegoods Assembly Instructions
President
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741566 Revision C-05
Page 1 of 2
Component Lateral File,
Pedestals, and Storage Unit
Tools Required
■Tape Measure ■#2 Phillips Head Bit
■Power Screwdriver ■3⁄16" Drill Bit
■Level
Package Contents
For Base: For Top:
■2 #8 x 11⁄4" Panhead Screws ■8 #8 x 11⁄2" Panhead Screws
(per lateral file or pedestal) (per modular unit)
■2 #8 x 5⁄8" Panhead Screws
(per lateral file or pedestal)
■4 #8 x 11⁄4" Panhead Screws
(per storage unit)
Installation
1. The component assembly uses a combination of modular
storage components and a component top and base which is
ordered separately. (Figure A). Remove shipping screws that
secure drawers and discard. Remove drawers from pedestals
by untying the anti-tip interlock cord. Review cord
attachment before removing drawers as cord must be re-tied.
Note: When drawers are re-installed make sure they are
returned to the same locations.
2. Place worksurface upside down on a clean, soft surface.
Position pedestals upside down on underside of worksurface
so they are flush with the back of the top and equal distance
from side to side. (Figure B). If a kneespace credenza is being
created, insert pedestals 11⁄2" from each edge of the top.
3. Attach pedestal to underside of worksurface utilizing
pre-bored holes of cleats/stretcher rails and provided
#8 x 11⁄2" panhead screws. (Figure B).
Note: Special care should be taken not to over drive the
screws through the worksurface.
Note: If installing file pedestals only, proceed to Step 6.
4. If installing a combination of file and storage units, the base
will need to be installed to the storage units at this time,
before turning unit upright. The base attaches to the
underside of storage pedestals and inside of file pedestals.
Figure A
Figure B
Pedestals flush
with back, equal
distance from
each end
#8 x 11⁄2 "
Panhead Screw
Top
(upside down)
Pedestal
(upside down)

Casegoods Assembly Instructions
President
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Form No. 1741566 Revision C-05
Page 2 of 2
Installation (continued)
5. Place base, upside down, on bottom of component units so
that it is flush with the backs and equal distance from side
to side.
Note: The base should extend beyond the pedestals
approximately 9⁄16 " on either end.
Fasten the credenza component base to the underside of the
storage components using the provided #8 x 11⁄4" panhead
screws, four per unit. (Figure C).
6. Carefully turn unit upright. If installing file pedestals only,
place them on the base so they are flush with the back of
the base and equal distance from each end.
Note: The base should extend beyond the pedestals
approximately ⁹⁄₁₆" on either end. (Figure D).
The file pedestals are attached to the base by inserting
provided screws through pre-drilled wooden cleats located
at the bottom rear of each unit, and by inserting provided
screws through a pre-drilled metal support bracket located
at the bottom front of each unit. (Figure E).
7. Use the #8 x 11⁄4" panhead screws to attach each pre-drilled
wooden cleat to the base (two screws per unit). Use the
#8 x 5⁄8" panhead screws to attach the pre-drilled metal
support rail to the base (two screws per unit). (Figure F).
8. Re-install drawers to original locations and re-tie anti-tip
cords. Level unit.
Caution: Failure to re-install anti-tip cords could result in
units tipping over, resulting in injury. Extra caution should be
given to the 4-high lateral unit.
Figure D
Figure C
Components flush
with back of base,
equal distance from
each end
Metal
Support Rail
#8 x ⁵⁄₈" panhead
screws inserted through
pre-drilled metal rail
(two per unit)
#8 x 11⁄4 " panhead screws inserted
through pre-drilled cleats (two per unit)
Cleat
Pre-drilled
Wooden cleats
Figure F
Metal Support Rail
Figure E
Base flush
with backs of
components
#8 x 11⁄4"
Panhead Screws
(four per component)
Base
(upside down)
Base
Base