Kimball Office Interworks EQ User manual

Assembly Instructions
Interworks®EQ P ge 1 of 3
Proper product in tallation, in accordance with the e in truction , i the re pon ibility of the in talling agent.
If you have any que tion concerning the e in truction , plea e call Kimball Office Cu tomer Service.
Part No. 2041383 Revi ion C-10
St ck ble P nel
Tools Required
Level, Screwgun with #2 M gnetic Phillips Bit (2 1⁄2" minimum long), 3⁄8" Socket or Wrench
Installation
For st ck ble p nels two people re recommended. B se p nel top c p will be moved on top of ssembled st ck ble p nel. In tr ck
of b se p nel, insert set of mounting br ckets, (note proper orient tion of br ckets). Connection bolts join b se p nel nd st ck ble
p nel securely.
Step 1
Prep Support Panel
• Remove top c p from b se p nel.
• Remove p nel hinges from st ck ble p nel. (Det il A)
• Use screwdriver to spre d p rt top ch nnel nd insert mounting br ckets into ch nnel. Center t b on br cket g inst inside edge of c ble slot on
ch nnel fr me. F sten br ckets to ch nnel fr me with screwgun nd self t pping screws.(Det il B)
Stackable
Panel Hinges
Detail A
Detail B
Lower Mounting
Bracket w/Threaded
Insert
Lower Mounting
Bracket w/Threaded
Insert
Connecting
Bolts
Self Tapping
Screws

Assembly Instructions
Interworks®EQ P ge 2 of 3
Proper product in tallation, in accordance with the e in truction , i the re pon ibility of the in talling agent.
If you have any que tion concerning the e in truction , plea e call Kimball Office Cu tomer Service.
Part No. 2041383 Revi ion C-10
Step 2
Prep Stackable Panel Assembly
• Remove tiles from st ck ble p nel.
- On f bric st ckers, push tile up g inst top of J ch nnel on st cker
fr me until bottom of tile cle rs lip of lower J ch nnel. Tilt bottom
of tile outw rd then pull down to remove it.
- On gl ss st ckers, remove the non-gl ss fr me h lf s described
bove. Remove the gl ss fr me h lf by first removing the screws
from the ret ining clips which secure the gl ss fr me to the st cker
fr me. Remove the ret ining clips, nd then remove the gl ss fr me
h lf s described bove.
St ck ble P nel, continued
Step 3
Install Stackable Panel Assembly
• Lower st cker ssembly onto the b se p nel. The round tubes from the
st cker p nel go into the vertic l tubes of the b se fr me. Lower both
sides of the st cker p nel simult neously to prevent binding.
• Insert connection bolt through holes in bottom cross-member of
st ck ble p nel, nd f sten into lower mounting br cket inst lled
previously in Step 1.
• Tighten connection bolt. Do not overtighten. Stop when bottom
cross-member begins to deform.
Connecting
Bolts
Remove screws
from retaining clips

Assembly Instructions
Interworks®EQ
Printed in U.S.A. © 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300
P ge 3 of 3
Proper product in tallation, in accordance with the e in truction , i the re pon ibility of the in talling agent.
If you have any que tion concerning the e in truction , plea e call Kimball Office Cu tomer Service.
Part No. 2041383 Revi ion C-10
St ck ble P nel, continued
Cut 10"
from Hinges
Base Panel
Hinges
Stiffener Bracket
Stackable Panel
(loaded on one side)
Base Panels
Step 4
Reinstall Hinges
Note: If stackable panel will be loaded on one side, go to Step 5.
• After st ck ble p nels re inst lled on b se p nel inst ll p nel
hinges between st ck ble p nels.
• Repl ce p nel top c ps.
Stackable Panels
Stackable Panel Hinges
Base Panels
Step 5
Stiffener Bracket
• Cut 10" from b se p nel hinges (cut must be str ight nd level).
•Inst ll shortened hinges into b se p nels.
• Inst ll stiffener br cket into st ck ble p nels nd b se p nels.
• Repl ce p nel top c ps.