Kimball Office KORE User manual

KORE™1of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2849274,A
Assembly Instructions
Accessory Rail Mounting
1. Locate the Mounting Brackets on the bottom of Accessory
Rail 3” off center. Locator features are present on the Ac-
cessory Rail.
2. Secure bracket to Accessory Rail using the supplied screws
4 screws per bracket are used on the Accessory Rail mount-
ing. See Figure A.
Fabric Frame Mounting
1. Locate the Mounting Brackets on the bottom of Framed
Screen 3” off center. Pre Drilled holes are present on the
Fabric Screen Frame.
2. Secure bracket to Fabric Screen frame using supplied
screws. 2 screws per bracket are used on the Fabric Screen
Frame mounting. .See Figure B.
3. Attach electrical blocks to brackets. 4 Trac Receptacles
snaps on brackets while the 8 Wire Block slides on to the
brackets.
Figure A– Accessory Rail Mounting
Electrical Bracket And Mount-
ing Block
Tools Required
Hardware Required (Included)
 Cordless driver with magnetic post and following tips
 #2 Phillips Driver
Installation
 8—#8 X 3/8” Panhead Sheet Metal Screws
 2 Mounting Brackets
Figure B– Fabric Frame Mounting
3.0 3.0
Figure C
4 Trac 8 Wire
3.0 3.0
Install Screws Here
Locator
Locator
Install Screws Here
Install Screws in Pre
Drilled Location
Install Screws in Pre Drilled Location

KORE™2of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2849274,A
Assembly Instructions
Jumper
Tools Required
Hardware Required
 N/A
None
Figure B
Figure A
1. Orient the jumper so the pen housing matches the power
block, as shown in Figure A.
2. Slide the jumper on to the power block. See Figure B.
Tip: on 8 Wire jumper it helps to start jumper on an
angle, toward the lock tab. then straighten as it engages
onto the block.
Installation
(Note: Make sure jumper is securely snapped to the
power block)
Power Block
Jumper
Keyed Housing
4 Trac
8 Wire
8 Wire
4 Trac
Lock
Tab

KORE™3of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2849274,A
Assembly Instructions
Power Entry
Tools Required
Hardware Required
 N/A
1– Power Entry
Figure B
Figure A
Notes: Reference labels on components for wiring dia-
grams Power Entry Box is unassembled from the factory
1. Make sure the Power Entry and the connecting piece are
oriented as shown in Figure A.
2. Slide the power entry on to the power block. See Figure
B.
Tip: on 8 Wire jumper it helps to start infeed on an an-
gle, toward the lock tab. then straighten as it engages
onto the block.
Warning: Connection to building power must be completed
by a licensed electrician. Installation must Be in accordance
with National Electrical Code and local codes. This system
may be connected to more than one source of supply. No sin-
gle circuit may be powered by more than one source. Do not
interconnect system electrical power from different feed units.
This can cause shock and fire hazard. Be certain all sources
are disconnected prior to any servicing.
Installation
(Note: You may have to unclip electrical
block to make modular connection)
8 Wire
Keyed Housing
4 Trac
8 Wire
4 Trac
Lock
Tab