Kimball Office Footprint User manual

Footprint®1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
1699149, Revision C
Assembly Instructions
File Center
Tools Required
Product Required
 Level
 Drill with #2 Phillips Bit
 Flat Head Screwdriver
 3/16” Hex Head Wrench
Removing Drawers
 Metal to worksurface: #10 X 1” Philips Pan Head Drill
Screws.
 Four spacers for use with systems surfaces only
Figure A
Figure B
Figure C
 These instructions provide the basic information to install
Footprint Flat Profile File Center. (Figure A):
- To Kimball systems TRAXX®-mounted, panel-mounted
and modular worksurfaces.
General Information
 Panel-mounted systems worksurfaces are illustrated.
 One person can perform all operations, although two may
be required to handle larger, heavier units.
3. Put one hand underneath drawer. Lift front of drawer up
to disengage from front drawer slide channel hooks.
(Figure C).
1. Begin with top drawer and extend drawer fully. (Figure B).
Note: Hooks in drawer channel correspond to notches
in drawer body.
 Drawers must be removed to secure storage to worksurface.
To remove box drawers and lateral file drawer:
2. Insert flat head screwdriver in between drawer and slide.
Pry slide away from drawer slightly. (Figure C).
4. When front of drawer is disengaged, pull entire drawer
towards you, supporting it from the bottom. This should
disengage drawer from rear drawer slide channel hooks.
(Figure C).
5. Set all drawers aside and slide drawer channels back into
case. Do not try to remove the entire drawer slide.
To Remove File Drawer
1. Extend drawer fully. (Figure D).
2. Each drawer slide has a lever: one is depressed, the other is
lifted. Simultaneously while lifting and depressing the levers,
hold drawer level and pull drawer toward you. This should
disengage drawer from file center unit.

Footprint®2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
1699149, Revision C
Assembly Instructions
(Continued)
 A wing panel or full end panel is required. (Figure E). 3/16”
Hex Head Wrench
1. Install any adjacent support brackets first.
Figure D
Figure E
Figure F
Systems Only:
3. Lay worksurface on level ground, front edge closest to you.
Secure #10x1" screws to worksurface in front and rear
pre-marked holes. DO NOT tighten screws all the way
down; leave about 1/4" of the screw head exposed. You'll use
these screws to align storage position.
4. Place spacers provided, one at each corner of file center.
(Figure E).
5. Lay worksurface on top of file center and align front and
rear "keyholes" in top of file center to screws pre-installed to
worksurface.
Note: If "keyholes" and screws in worksurface do not
align, remove screws from worksurface and reinstall with
worksurface laying on top of file center.
6. Install modesty panel and remaining support.
Modular Casegoods Only:
Systems and Modular Casegoods:
7. Secure storage to worksurface (THROUGH spacers, if used)
with remaining #10x1" screws provided.
8. Adjust glides as needed with hex:
- Right to lower
- Left to raise
3. Set drawer aside and slide drawer channels back into case.
Do not try to remove the entire drawer slide.
Installation
Drawer Replacement (Figure F)
 Extend slide cabinet members.
 Make sure chrome ball bearing member is also forward.
 Carefully align slide drawer members with cabinet
members and gently push drawer closed. Check for
proper alignment by inspecting drawer front margins
for spacing and squareness.
2. Slide File Center under worksurface and position so that the
worksurface extends 1/8” beyond where the drawers would
be if they were installed. Mark hole locations accordingly.