Kimball Office Footprint User manual

Footprint®1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
2464685, Revision -
Assembly Instructions
Sliding Door, Metal Panel
Mount Overhead for Xsite®
Tools Required
Hardware Required
1. If installing on an Xsite panel with Tackable Acoustic
Tiles, verify that there is a mid-frame support located
where the bottom of the cabinet will be. (Figure A)
2. Remove the inner back panels from the cabinet. Lift the
panel straight up using the hole provided near the bottom.
Grasp the panel at the top and pull toward you. While
holding the panel horizontally with the top facing the front
of the cabinet, turn the panel approximately 30 degrees and
pull straight out to remove it. (Figure B)
3. Insert the threaded studs on the mounting brackets through
the holes on the back of the cabinet. The top inside stud
goes through the round hole. The other studs go through
the slotted holes.
4. From the inside of the cabinet place a 1/4” flat washer and
1/4” acorn nut on each of the studs. Using a 7/16” wrench,
socket, or nut driver, tighten the acorn nuts, making sure
that the mounting bracket is square to the cabinet. (Figure
C)
5. Repeat for the opposite side.
Installation
 Overhead Mounting Brackets (2 each)
 1/4” Flat Washer (8 each)
 1/4” Acorn Nut (8 each)
 Ganging Bracket (If installing 2 cabinets side-by-side)
 #8 X 5/8” Phillips Head Sheet Metal Screws (6 each, used
with Ganging Brackets)
 Phillips Screwdriver or Cordless Drill with #2 Phillips
Bit
 7/16” Wrench, Socket, or Nut Driver
 Level
Figure A
Mid-frame Support
Figure B
Figure C
Acorn Nut
Washer Mounting Bracket

Footprint®2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
2464685, Revision -
Assembly Instructions
Sliding Door, Metal Panel
Mount Overhead for Xsite®
Installation (continued)
6. Using 2 persons, tilt the bottom of the cabinet out approxi-
mately 15 degrees and insert the upper tab of the mount-
ing brackets into the groove on the Traxx extrusion. Push
the upper tab as far up into the extrusion as possible, then
rotate the cabinet back parallel to the Xsite panel, allowing
the lower hooks of the mounting brackets to swing into the
extrusion slot. Lower the cabinet until the lower hooks are
fully seated on the lower flange of the extrusion. (Figure
D)
7. Let the cabinet rest against the panel. Place a level on top
of the cabinet from front to back. Level the cabinet by
loosening the screws on the leveling bracket at the bottom
of the cabinet. Slide the leveling bracket forward or back-
ward until the cabinet is level. Re-tighten the screws.
(Figure E)
8. Re-install the inner panels.
9. If cabinets are installed side-by-side, a ganging bracket is
required. Attach the ganging bracket to the bottom edges
of the end panels of two adjacent cabinets and secure with
the #8 X 5/8” sheet metal screws provided. Make sure that
the top, bottom and front edges of the cabinet are aligned.
It may be necessary to hold the cabinets together with “C”
clamps until the ganging bracket can be secured. If “C”
clamps are used, use a piece of wood or other non-marring
material between the clamps and cabinet and do not over-
tighten. (Figure F)
Figure D
Figure E
Leveling Bracket
Screws
Figure F
Ganging Bracket
#8 X 5/8” Sheet
Metal Screws