Kimball Office Footprint Bevel Profile Highback Organizer User manual

Assembly Instructions
Footprint® Page 1 of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Oce Customer Service.
Part No. 2112655 Revision E
Bevel Prole Highback Organizer
Tools Required
Drill Level
#2 Phillips head bit Tape Measure
Package Contents
Overhead storage unit Four #8 x 3/4” Phillips pan
Two end panels head drill screws
(non-handed) 18 #10 x 1/2" hex washer
Tackboard envelope head drill screws
Shipped Separately
Tackboard Lock(s)
Description
These instructions provide basic information to assemble a
Footprint bevel prole highback organizer and attach it to a
Footprint freestanding modular worksurface with metal
support or storage. Highback organizer must be the same
width as the rectangular freestanding unit. Highback organizer
is shipped ready to assemble (Figure A).
Note: One person can perform all operations, although two may
be required to handle larger, heavier units.
Installation
1. Close and lock receding doors in overhead storage unit to
prevent them from sliding open during installation.
Note: Locks are shipped separately from the unit. It is
recommended that you install the lock prior to installation.
2. Turn overhead storage unit upside down with the door
facing you.
3. Remove inset pieces from end support panels. With the
smooth side of the left end support panels facing outward,
secure the panel to the underside of the storage unit using
three #10 x 1/2 " screws in pre-drilled hold locations. Repeat
for the right end support panel (Figure B).
Figure A
Figure B
End support
panel—
Smooth side
f
aces outward
Removable
Inset Piece
End support panels
Tackboard
Envelope
Overhead
Storage

Assembly Instructions
Footprint® Page 2 of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Oce Customer Service.
Part No. 2112655 Revision E
Bevel Prole Highback Organizer,continued
4. With nished, smooth side of the tackboard envelope
facing outward, and 45° cutouts facing upward, slide
tackboard envelope down and in between the installed
end support panels. Secure tackboard envelope to storage
unit and end panels using #10 x 1/2” screws (Figure C).
5. Ensure that the freestanding unit is properly assembled and
level.
6. Turn assembled highback organizer right side up. Place on
top of freestanding unit, ush to the rear edge of the unit.
Outside edge of each end support panel should be about
1/8” inset from the edge of the worksurface (Figure D).
7. Secure the highback organizer to the worksurface of free-
standing unit using two #8 x 3/4" screws per end support
panel (Figure D).
8. Replace inset pieces on both end support panels.
Figure C
Figure D
Tackboard
Envelope
Smooth side
f
aces outward

Assembly Instructions
Footprint® Page 3 of 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Oce Customer Service.
Part No. 2112655 Revision E
Bevel Prole Highback Organizer,continued
9. With 45° cutouts pointing downward, slide the top of the
tackboard up and into the tackboard envelope (Figure E).
Note: Highback organizer must be properly assembled,
installed onto the worksurface, and level before installing the
tackboard.
Figure E
Figure F—Assembled and Installed Unit
Printed in U.S.A. © 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300