Kimball Innsbruck User manual

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
© 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Innsbruck/Osterely Park™
Assembly Instructions
1998758 Revision A-10
Complete Series Master Packet

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2002 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1567897 Revision A-02
Page 1 of 1
Component Worksurface Bridge
Tools Required
■Level
■Power Screwdriver
■#2 Phillips Head Bit
Package Contents
■32 #8 x ³⁄₄" Panhead Screws
Installation
1. The component worksurface bridge is positioned between
two pedestal units to create a kneewell/worksurface area.
(Figure A).
2. Place the pedestal units in their desired location. Attach
metal L-brackets flush with the underside of top using
#8 x ³⁄₄" screws, provided. Position component bridge
between the pedestal units. Level and adjust units so that
matching surfaces are flush and have no gaps. Attach
component bridge to L-brackets using #8 x ³⁄₄" screws,
provided. (Figure B).
Figure A
Figure B
Metal
L-Bracket
Component
Worksurface
Bridge

Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Service.
Part No. 1567899 Revision B-08
Page 1 of 1
Overhead Cabinet
Tools Required
ILevel IPower Screwdriver
I#2 Phillips Head Bit I7⁄32" Drill Bit
Package Contents
ITapped Sleeve Connectors IM4 screws
Description
The overhead cabinet mounts as a suspended unit between
two set-on-surface bookcases.
Installation
1. Make sure lower unit is level. Place the set-on-surface
bookcase units in the desired location. Align the overhead
cabinet flush with the back edges of the adjoining set-on-
surface bookcases. (Figure A)
Note: The overhead cabinet cornice frame will be offset 11⁄2"
behind the bookcase cornice frames.
2. Using a 7⁄32" drill bit, bore through a shelf hole from the
overhead cabinet into the adjoining bookcase unit. (Figure B)
Note: Holes for adjustable shelves have been pre-bored in a
1" boring pattern into the inside end panel of each cabinet
and bookcase.
3. Using the tapped sleeve connector, align and fasten the cabinet
to the bookcase using an M4 screw, provided. (Figure C)
4. Repeat steps 2 and 3, installing a minimum of four screws
per side panel.
Caution: A suspended cabinet should not be connected to
another suspended cabinet. (Figure D)
Figure A
Figure B
Figure C
Overhead
Figure D
Tappe d
Sleeve
Screw
Cornice
frame

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1699215 Revision A-03
Page 1 of 1
Printed in U.S.A. © 2003 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Pediment Bridge
Tools Required
■Scissors or Utility Knife ■Ruler or Tape Measure
Package Contents
■1 Pediment Bridge ■1 Double-sided Adhesive Tape
Installation
1. Included with the pediment bridge is a roll of double-sided
adhesive tape (shipped in the same carton) for attachment
of the bridge to the overhead cabinet. (Figure A).
2. Attach a strip of the double-sided adhesive tape to the top
edge of the overhead cabinet on all three sides. (Figure B).
3. Remove the peel coat from the adhesive tape. Secure the
pediment bridge in the desired location. (Figure C).
Caution: The double-sided tape has a very strong adhesive
that bonds instantly to any surface to which it is applied.
Figure A
Figure C
Apply tape
Figure B
Remove peel coat
Attach pediment bridge

Casegoods Assembly Instructions
President/Senator/Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741515 Revision A-04
Page 1 of 2
Table Desk
Tools Required
■Level ■³⁄₄" Socket
■Socket Wrench
Package Contents
■1 Table Desk ■4 Table Leg with Lag Bolt,
Washer, Lock Washer and Nut
Installation
Note: This instruction shows the President Table Desk
assembly as an example. This instruction can also be
applied to Senator and Innsbruck/Osterley Park Table
Desk assembly. For safety, and to avoid damage to the unit,
it is recommended that more than one person be used to
assemble and move the Table Desk.
1. The table desk will arrive unassembled with the legs
located on the underneath side of the worksurface.
Carefully un-carton and place worksurface face down on
a smooth, clean, soft surface. (Figure A).
2. Remove the table legs from the underside of the
worksurface and remove all foam packing. Legs are
numbered 1, 2, 3, and 4 on their top ends to correspond
with their appropriate corner location, which is numbered
on the underside of the worksurface. (Figure B).
3. During production, a wooden spacer is fastened to the
apron rail where the legs attach. Normally, they are removed
before shipment. However, if any spacers remain on the
apron rail please remove and discard all of them as they
will interfere with installation of the table legs. (Figure C).
4. Locate the table leg numbered “1” and remove the nut,
lock washer, and washer from the lag bolt. (Figure D).
Figure A
Figure B
Top of leg is numbered to
match with number on
underside of worksurface
Figure C
Figure D
Remove any and
all spacers from
apron rail
Remove all hardware
from lag bolt

Casegoods Assembly Instructions
President/Senator/Innsbruck/Osterley Park
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741515 Revision A-04
Page 2 of 2
Installation (continued)
5. Insert the lag bolt through the hole in the corner block at
the corner numbered “1” on the worksurface. (Figure E).
6. Secure the leg to the table by installing the hardware in the
following order: washer, lock washer, nut – to the outside of
the corner block. Make sure the leg is perpendicular and
flush to the apron rails. Tighten the nut firmly by using the
³⁄₄" socket wrench, but do not over-tighten. (Figure F).
7. Refer to Steps 4, 5, and 6 to install legs “2”, “3”, and “4” to
their corresponding locations. (Figure G).
8. After all legs are installed, carefully turn table to the upright
position. If the table displays a swaying motion, then one or
more of the legs are not properly seated in their locations.
Turn the table back over on the soft surface and re-check all
legs to make sure they are perpendicular and flush to the
apron rails and that all fasteners are properly installed and
tightened. (Figure H).
Figure E
Figure F
Figure G Figure H
Make sure number
on leg and on the
worksurface are
the same
Install hardware
in this order
Perpendicular
and flush against
apron rails
Insert Lag Bolt
through
Corner Block

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2005 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741543 Revision A-05
Page 1 of 1
Glass Shelf Removal and
Adjustment
Tools Required
■None
Package Contents
■None
Installation
Note: Shelves are shipped uninstalled.
1. An adjustable shelf consists of a shelf and four (4) shelf
support brackets. (Figure A).
2. All cabinets feature pre-bored holes 11⁄4" apart.
Recommended spacing is #2 position, for proper ring
binder clearance. (Figure B).
3. For repositioning of shelves, remove shelf and move shelf
support brackets to desired hole locations. Make sure all
brackets are at the same level.
Figure A
Figure B
Shelf
Shelf Support
Bracket
1
2
3
1
2
3

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741544 Revision A-05
Page 1 of 2
Drawer Removal, Adjustment,
and Unit Leveling
Tools Required
■7⁄32" Nutdriver ■Phillips Screwdriver
■Level ■Tape Measure or Ruler
Installation
1. For desk, credenza, return, bridge, lateral file & drawer or
door storage and bookcases (as applicable): Remove all
drawers as required to access leveling glide adjustment
holes.
2. To remove drawers: Extend the box or file drawer to its
full extension. Locate the drawer slide release tab, in the
approximate location shown, on each side of the drawer
box. Press both tabs in and pull drawer straight out until
slide drawer members disengage from cabinet members.
(Figure A).
3. To remove lateral file drawers, extend the drawer forward.
(Figure B). Press the two quick-disconnect release tabs
and lift the drawer off the slide assembly. (Figure C).
Note: Shipping screws must be removed from drawer
suspensions before drawer can be removed.
4. Turn the leveling glides fully “in” (counterclockwise)
prior to leveling. Level the unit from front to back by
first extending the glides on the outside corners
(turn clockwise), then level the unit from side to side.
Check adjustments by placing the level at the four positions
shown. Adjust inside glides, if applicable, to help support
the unit. (Figure D).
5. Replace all drawers to their original locations. To re-install,
fully extend cabinet slide members, making sure the chrome
ball-bearing members are also forward. Carefully align
drawer slide members with cabinet slide members and
gently push drawer closed. Check for proper alignment by
inspecting drawer front margins for spacing and squareness.
Figure A
Figure B
Release Tabs
Figure C
Figure D
Leveling Glide
Adjustment Hole
7⁄32"
Nut Driver
Level;
Check at four locations

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741544 Revision A-05
Page 2 of 2
Installation (continued)
6. If drawer front needs adjustment, open drawer and locate
the four (4) Deerwood screws that attach the drawer front
to the drawer box. (Figure E).
Note: Lateral file drawer fronts use six (6) screws.
7. Slightly loosen Deerwood screws and adjust drawer front
to the approximate locations and gaps shown. (Figure F).
Re-tighten all Deerwood screws. Repeat Steps 6 and 7 to
adjust other drawers in unit.
Figure E
Figure F
3⁄16" gap
Printed in U.S.A. © 2005 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Deerwood Screws (4)
3⁄16" gap

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741545 Revision A-05
Page 1 of 2
Wood Shelf Removal and
Adjustment and Door Hinge
Adjustment
Tools Required
■Phillips Screwdriver
Package Contents
■None
Installation
Note: Shelves are secured in unit with shipping screws.
1. An adjustable shelf consists of a shelf and four (4) shelf
support brackets. (Figure A).
2. All cabinets feature pre-bored holes 11⁄4" apart.
Recommended spacing is #2 position as shipped, for proper
ring binder clearance. (Figure B).
3. For repositioning of shelves, the shipping screws must be
removed. (Figure C). Remove shelf and move shelf support
brackets to desired hole locations, making sure all brackets
are at the same level.
4. For additional security, adjustable shelves can be fastened
into position by reusing the #6 x 5⁄8" panhead shipping
screws.
Figure B
Figure C
Shelf
Shelf Support
Bracket
1
2
3
1
2
3
Figure A
Shelf Support
Bracket
#6 x 5⁄8" Panhead
Shipping Screw

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2005 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741545 Revision A-05
Page 2 of 2
Installation (continued)
5. Side Adjustment:
Turn front screw clockwise to decrease door inset,
counterclockwise to increase inset. (Figure D).
Note: Adjust margins around doors to be equal.
6. Depth Adjustment:
Loosen back screw. Adjust door to desired position and
re-tighten screw. (Figure E).
7. Height Adjustment:
Loosen screw(s) on the mounting plate. Adjust door to
position and tighten screws. (Figure F).
8. Door Removal and Installation:
To remove, pull release lever back. (Figure G). To re-install,
place the hinge on the mounting plate and push the hinge
with finger pressure. The snap sound confirms a secure
attachment.
Figure E
Side Adjustment
Figure F
Figure G
Removal
Figure D
Height Adjustment
Depth Adjustment

Casegoods Assembly Ins ruc ions
Innsbruck/ sterley Park
Proper product installation, in accordance with these instructions, is the responsibilit of the installing agent.
If ou have an questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741563 Revision E-09
Page 1 of 2
Bridge Unit
Tools Required
■Level ■Screw Gun
■#2 Phillips Head Bit ■Drill Bits
■Tape Measure
Package Con en s
■4 Flat Brackets ■44 #10 x 1" Panhead Screws
■2 Align-n-lock Fasteners ■Double-sided Tape
■4 #8 x 5⁄8" Panhead Screws ■4 Hinges
Ins alla ion
1. The hinged modesty/bridge unit arrives un-assembled in
a carton. Place the bridge face down on a smooth, hard
surface. Take care to not mar the worksurface. (Figure A).
2. The bridge and modesty panel have pre-drilled holes used
to attach the two units together with supplied hinges. Attach
the hinge to the modesty panel using three #10 x 1" panhead
screws in each hinge. Attach the modesty panel to the bridge
using three of the provided #10 x 1" panhead screws in each
hinge. (Figure B).
3. Turn the bridge assembly upright. The bridge assembly can
be mounted between a single pedestal desk and credenza.
(Figure C).
4. Position the main units in the desired locations. Leave
enough space between the two units to allow for placement
of the bridge. Level main units. Install the flat brackets
to the undersides of the main units using the provided
#10 x 1" panhead screws. Locate the flat brackets using the
dimensions shown. Center the brackets with the edge of the
unit worksurfaces. (Figure D).
Figure B
Figure C
Figure A
Figure D
4"
19"
Mount Align-n-lock
fastener to pre-drilled holes

Casegoods Assembly Ins ruc ions
Innsbruck/ sterley Park
Printed in U.S.A. © 2009 Ki ball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibilit of the installing agent.
If ou have an questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741563 Revision E-09
Page 2 of 2
Ins alla ion (con inued)
4. (continued)
Note: Flat brackets are shipped on the underneath side of
the bridge top.
Use the pre-drilled holes to install the quick align-n-lock
fastener to the end panel of the desk using the #8 x 5⁄8"
panhead screws. (Figure D). The fastener is shipped in the
bridge hardware bag.
5. Align the bridge worksurface to the main units. Position
the tops so the outer edges of the main units and bridge
worksurface are tight and flush against each other with no
gaps. Attach the bridge worksurface to the flat brackets
using the provided #10 x 1" panhead screws. (Figure E).
6. Level all units. Align all margins vertically between the
modesty panel and desk/credenza end panels. Eliminate all
gaps. Engage quick align-n-lock fasteners on lower portion
of modesty panel and rotate latch handles firmly. (Figure F).
Adjust levelers on modesty panel snug to floor.
Note: Do not over-tighten levelers, otherwise units will
become mis-aligned. (Figure G).
7. After unit is assembled, attach the enclosed flat mouldings
and capitals over the seams where the bridge attaches to the
desk and the credenza. Center the pieces over the seams and
attach with enclosed double-sided tape. (Figure H).
Caution: When the bridge unit is placed against a wall we
suggest the flat moulding and capital not be installed as the
hinged modest will no longer swing open for wall access.
Figure F
Figure H
Figure E
No gaps
No gaps
Do not over-tighten levelers
Figure G
Main unit
Align
Flush with
no gaps Bridge
Flat Capital
Flat Moulding
Center pieces
over seam

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741564 Revision A-05
Page 1 of 2
Glass Shelf Removal and
Adjustment and Door Hinge
Adjustment
Tools Required
■Phillips Screwdriver
Package Contents
■None
Installation
Note: Shelves are shipped uninstalled.
1. An adjustable shelf consists of a shelf and four (4) shelf
support brackets. (Figure A).
2. All cabinets feature pre-bored holes 11⁄4" apart.
Recommended spacing is #2 position, for proper ring
binder clearance. (Figure B).
3. For repositioning of shelves, remove shelf and move shelf
support brackets to desired hole locations. Make sure all
brackets are at the same level.
Figure A
Figure B
Shelf
Shelf Support
Bracket
1
2
3
1
2
3

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2005 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741564 Revision A-05
Page 2 of 2
Installation (continued)
4. Side Adjustment:
Turn front screw clockwise to decrease door inset,
counterclockwise to increase inset. (Figure C).
Note: Adjust margins around doors to be equal.
5. Depth Adjustment:
Loosen back screw. Adjust door to desired position and
re-tighten screw. (Figure D).
6. Height Adjustment:
Loosen screw(s) on the mounting plate. Adjust door to
position and tighten screws. (Figure E).
7. Door Removal and Installation:
To remove, pull release lever back. (Figure F). To re-install,
place the hinge on the mounting plate and push the hinge
with finger pressure. The snap sound confirms a secure
attachment.
Figure D
Side Adjustment
Figure E
Figure F
Removal
Figure C
Height Adjustment
Depth Adjustment

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741582 Revision B-04
Page 1 of 2
Executive Return
Tools Required
■Level ■Screw Gun
■#2 Phillips Head Bit ■Drill Bits
■Tape Measure
Package Contents
■16 #10 x 1" Panhead Screws ■10 #8 x 1¹⁄₄" Panhead Screws
(for flat brackets) (for connecting rail)
■2 Flat Brackets
Installation
1. The executive return arrives assembled in a carton. It can
be attached to a single pedestal desk. (Figure A).
2. Place the desk and return in their desired location. Level
both units. Attach the flat brackets to the underside of the
main unit at the locations shown, using the provided
#10 x 1" panhead screws. Center the flat brackets with the
edge of the main unit. (Figure B).
3. Align the return to the main unit. Position the tops so the
outer edges of the main and return units are flush and
pulled tight against each other with no gaps. Fasten the
return top to the flat brackets using the provided
#10 x 1" panhead screws. (Figure C).
Note: Flat brackets are shipped on the underneath side of the
return top.
Figure A
Figure B
Figure C
Executive
Return
19"
4"
Main unit
Flush Return
Align

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care Teams.
Part No. 1741582 Revision B-04
Page 2 of 2
Installation (continued)
4. Align the main unit end panel and the return unit modesty
panel to eliminate any gap between them. This can be done
by adjusting the levelers up/down on the return or main
units. Once any gap is eliminated, attach the main unit to
the return unit using the return connecting rail and the
#8 x 1¹⁄₄" panhead screws provided. Re-level units.
(Figure D).
Note: Connecting rail is shipped on the underneath side
of the return top.
5. After unit is assembled, attach the enclosed flat moulding
and capital over the seam where the return attaches to the
desk. Center the pieces over the seam and attach with
enclosed double-sided tape. (Figure E).
Figure E
Figure D
Flat Capital
Center pieces
over seam
Flat Moulding
Return
Connecting Rail
Return
Main Unit

Casegoods Assembly Instructions
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Page 1 of 1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741593 Revision A-04
Lock Core Installation
Tools Required
■None
Package Contents
■Lock Core/Key
(key may be either rectangular or round head)
Installation
1. The key is pre-inserted into the lock core. Do not remove
the key prior to lock core installation. (Figure A).
2. Prior to inserting the lock core/key be sure that the lock
tenon on the end of the lock core is aligned with the cutout
at the back of the drawer/door lock housing. (Figure B).
3. To install the lock core, angle the core slightly so that the
raised wafer (Figure B) can be inserted into the lock
housing. When the wafer is inside the housing, straighten
the core and push in firmly to fully seat the core in the lock
housing. (Figure C).
4. The lock core will only seat properly when the lock tenon
and housing cutout are correctly aligned. You will not be
able to remove the key if the core is not fully engaged and
properly seated in the housing. (Figure D).
Note: Future removal of lock cores require a yellow Change
Key, ordered separately.
Figure A
Figure B
Lock core with
pre-inserted key
Lock
Housing Drawer or
Door Front
Figure C Figure D
Raised Wafer
Align Tenon and cutout
prior to insertion
Angle to insert
Raised Wafer
Lock Tenon
Core fully seated
Lock Housing Straighten
and push in
Core not fully seated

Assembly Instructions
Universal
Pri ted i U.S.A. © 2010 Kimball I ter atio al, I c. T 800.482.1818 F 812.482.8300
Page 1 of 1
Proper product installation, in accordance with these instructions, is the responsibilit of the installing agent.
If ou have an questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741615 Revisio D-10
Tack oards and/or
Powered Tack oards
Tools Required
■Drill/Screw Gun ■Level
■#2 Phillips Head Bit ■Small Blade Screwdriver
Hardware Required
■#8 x ⁵⁄₈" Flathead
Installation
1. Tack oards can e attached to any high ack organizer to
provide a tacka le surface. Tack oards can also e wall
mounted. The tack panel is provided with routed
channels on the ack side to help manage cords. (Figure A).
2. Insert a screw into the hole of each loose Dual Lock™ pad,
4 or 6, as required. (Figure B).
3. Press pads with screw protruding against the pads which are
already mounted to the ack of the tack oard, locking the
pads together. Position tack oard on mounting surface,
making sure it is level. Apply pressure on oard over pads
to mark surface with screw points. (Figure C).
4. Carefully detach pads with small lade screwdriver and
fasten in locations previously marked in step 3. Position
tack oard against mounting surface, making sure it is level,
and engage until each pair of pads snap together.
5. Wall Mount Caution: Pads should be located on wall studs,
or secured to wall with anchors (not provided).
Figure A
Figure B
Figure C
Ca le
Routes
Dual Lock

Casegoods Assembly Instructions
Innsbruck/Osterley Park
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1847163 Revision A-06
Page 1 of 1
Conference Table Top
Tools Required
■Adjustable Wrench ■Phillips Screwdriver
■7⁄64 Allen Wrench
Package Contents
■Table Top ■12 Bolts
■2 Mounting Pads ■12 Washers
Caution: It is recommended that more than one person be used
to assemble and move conference tables.
Installation
1. Place the worksurface upside down on a smooth, solid
surface. Match the straight ends and align the mechanical
leveling devices. (Figure A).
2. For each leveling device thread the bolt into its opposite
bracket, attach nut, and tighten firmly. (Figure B).
3. Position the two mounting pads so that the holes in the
mounting pad align with the T-nuts in the top. (Figure C).
4. After bases have been installed and table/base assembly is
turned upright, use the leveling set screws in the leveling
devices to align straight ends of the assembly. (Figure B).
Figure A
Figure B
Figure C
Thread bolt
into nut
and tighten
Align
two-piece top
Mounting
Pad
T-nuts towards
outer edge
Washer
and Bolt
combination
Leveling
set-screw
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300