Kimball Kore User manual

Kore® 1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3139104,D
Assembly Instructions
1. Unpack all components.
2. Assemble metal frame by placing Left Frame on
clean soft surface. Slide the Connector Rail over the
upper “U” bracket and secure with 2 M5 Flathead
screws. See Figure A.
3. Slide Lower Horizontal Weldment over lower Brack-
ets but do not install the screws at this time. See Figure
A.
4. Place the Right Frame assembly on top of assembly
and secure in place with remaining 2- M5 Flathead
screws into the connector rail. The screws holding the
Lower Horizontal Weldment will be installed after the
back panel has been installed. See Figure A.
5. Install back panel by first flipping the cart assembly
on its front as seen in Figure B. Place a supplied spring
and wood dowel in each slide of the back panel. Slide
the dowels on the top of the back panels into the oblong
holes on the Connector Rail. Compress the springs on
the sides by pressing the dowels into the holes while
pivoting the back panel into place until the bottom of the
back panel is seated securely on the Lower Horizontal
Weldment. Without the screws in place, the Lower Hori-
zontal Weldment should slide down and provide room to
insert the back panel.
6. The spring should push the side dowels into the
mating oblong holes on the frame and you should here a
“Click”. Secure the bottom of the back panel to the Low-
er Horizontal Rail with the supplied #8 -1” wood screws.
Secure the Lower Horizontal Weldment with the 8- M5
Button head cap screws.
Tip: Ensure any loose felt is completely tucked into
seam by pushing it into seam using a plastic card.
7. Lay the cart on its back to install the Height Adjust
Column. Slide the Column Bracket over the Height Ad-
just Column with the flange down then insert the Height
Adjust Column into the square cutout in the Lower Hori-
zontal Weldment. Attach the Height Adjust Column to
the Lower Horizontal Weldment using the supplied M8
Cap Screws.
Mobile Workstation - Adjustable Height Surface
Tools Required
• 4mm hex bit
• 6mm hex bit
• 3mm hex bit
Installation
• 4 - M5 X 8 Flat Head Cap Screws
• 8 - M5 X 8 Button Head Cap Screws
• 4 - M8 X 25 Cap Screws
• 25 - #10 x 7/8” Phillips Woodscrew
Figure A
Figure B
• 2 - Black Wood Dowels
• 2 - Springs
• 6 - #8 X 1” Wood Screws
• 2 - #8 x 5/8” Phillips Woodscrew
Hardware
Column Bracket
(Flange down)
Install before
attaching
column.
Height Adjust
Column
• #2 Phillips bit
• Drill or impact driver
• Tape Measure

Kore® 2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3139104,D
Assembly Instructions
8. Locate the Column support using the predrilled holes in the
back panel and secure to the back panel with the supplied 2-#8
X 5/8" wood screws. Figure C.
9. Install the worksurface by first setting the cart assembly
upright. Place the surface, surface side up, on the worksurface
support frame, holding a 1” inset from the front of the frame and
holding a 1” gap on either side of the surface. Secure with sup-
plied 15 - #8-7/8” wood screws.
Tip: If undersurface Cubbies are to be installed on cart, at-
tach it prior to installing surface.
10. Locate the Column Handle on the front Right side of the
surface, 1/8” inset and attach using 2 X #8 - 1” wood screws.
11. Take the column base though its full range of motion to en-
sure it travels smoothly. Remove any access grease from the
column using clean towel. Ensure casters track smoothly on
intended surface.
Installation (Continued)
Figure D Figure E
Figure C
Column
Handle
Column Support
Bracket