Kimball XSEDE User manual

XSEDE® Height Adjust
1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3049377,B
Assembly Instructions
1. Assemble Feet to the Columns using supplied Socket Round
5/16-18 X 5/8” screws. Tighten Screws Firmly. See Figure B.
IMPORTANT: Make sure the correct screws are used. Using
longer screws may destroy the internal parts of the column.
2. Loosen the set screw and set the Crossbar length based on
top size as seen in Figure C below. Attach the crossbars on
the long side of the bases using supplied Socket Flat Head
5/16-18 X 1” screws. See Figure C.
IMPORTANT: Make sure the correct screws are used. Using
longer screws may destroy the internal parts of the column.
Figure A
Assembled Product
Xsede Height Adjust
Freestanding T-Leg Base
Hardware
4—Round Head Socket 5/16-18 X 5/8”
8—Flathead Socket 5/16-18 X 1”
4– Flathead Phillips 1/4-20 X 5/8”
8-Clear Bumpers 1/2” Round X 1/8”
2-Clear Bumpers 1/2” Square X 1/4”
8-Panhead Phillips #8X3/4” Wood Screw
4-Flathead Phillips #10-2 3/8” Wood Screw
4– Panhead Phillips #8 X 5/8” Wood Screws
2-Cable ties.
1— Power Supply Bracket
Installation
Crossbar
Sidebar
Column
Foot
Figure B– Attach Feet
Figure C– Attach Cossbar
Do not use middle hole of cross bar
Tools Required
• 3/16” Hex Drive
• #2 Phillips Drive
• Drill
48”
54”
60”
66”
72”
Top

XSEDE® Height Adjust
2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3049377,B
Assembly Instructions
3. Attach sidebars to crossbars with Phillips Flathead 1/4-20” X
5/8” screws. See Figure D
4. Place adhesive bumpers on the crossbars. The bumpers
should be places as close to the fixing screws as possible.
The bumpers come in two thicknesses. The thicker, square
ones are used on the inner tube. See Figure E.
5. Slide Power Supply Bracket over crossbar as shown in Fig-
ure F.
6. Attach Base to a worksurface using supplied Panhead
#8X3/4” and flathead #10X2-3/8” wood screws. Route hand-
set Cable between the Crossbar and the surface prior to
attaching. The shorter screws goes in the sidebars. The
longer screws go into the crossbars. See Figure G.
IMPORTANT: supplied screws are designed to work with a
worksurface with a minimum thickness of 3/4”
Figure D– Sidebar Attachment
Base-Only Assembly
Installation Continued
Figure E– Spacing Bumpers
Figure G– Worksurface Attachment
Figure F– Power Supply Support
(3 1/2”)
(3 1/2”)
16 7/16” 16 7/16”

XSEDE® Height Adjust
3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3049377,B
Assembly Instructions
6. Attach the handset to front edge of the worksurface using in-
cluded #8 X 5/8” Panhead Wood Screws. Connect the cables
and power supply. Use Cable Ties to secure wiring to base. En-
sure no cables are hanging down. See Figure H.
Figure H– Electrical Assembly
Base-Only Assembly
Installation Continued
Control Box
Power Supply
Power Cable
Handset
Warning leaflet and user manual should be
Warning Leaflet Electric User Manual