Kimball XSEDE Height Adjust User manual

XSEDE® Height Adjust
1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3111703,-
Assembly Instructions
1. Assemble Feet to two Columns using supplied Socket
Round 5/16-18 X 5/8” screws. Tighten Screws Firmly. See
Figure B.
IMPORTANT: Make sure the correct screws are used. Using
longer screws may destroy the internal parts of the column.
2. Loosen the set screw and set the Crossbar length based on
top size as seen in Figure C below. Attach the crossbars on
the long side of the bases using supplied Socket Flat Head
5/16-18 X 1” screws. See Figure C.
IMPORTANT: Make sure the correct screws are used. Using
longer screws may destroy the internal parts of the column.
Figure A
Assembled Product
Xsede Height Adjust 3 Column
T-Leg
Hardware
4—Round Head Socket 5/16-18 X 5/8”
12—Flathead Socket 5/16-18 X 1”
4– Flathead Phillips 1/4-20 X 5/8”
12-Clear Bumpers 1/2” Round X 1/8”
4-Clear Bumpers 1/2” Square X 1/4”
8-Panhead Phillips #8X3/4” Wood Screw
12-Flathead Phillips #10-2 3/8” Wood Screw
4– Panhead Phillips #8 X 5/8” Wood Screws
4-Cable ties.
1— Power Supply Bracket
Installation Figure B– Attach Feet
Figure C– Attach Cossbar
Do not use middle hole of cross bar
Tools Required
• 3/16” Hex Drive
• #2 Phillips Drive
• Drill
Sidebar
Column
Foot
Crossbar
48”
54”
60”
66”
72”
Top

XSEDE® Height Adjust
2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3111703,-
Assembly Instructions
3. Attach sidebars to crossbars with Phillips Flathead 1/4-20” X
5/8” screws. See Figure D
4. Place adhesive bumpers on the crossbars. The bumpers
should be places as close to the fixing screws as possible.
The bumpers come in two thicknesses. The thicker, square
ones are used on the inner tube. See Figure E.
5. Slide Power Supply Bracket over crossbar as shown in Fig-
ure F.
6. Attach Base to a worksurface using supplied Panhead
#8X3/4” and flathead #10X2-3/8” wood screws. Route hand-
set Cable between the Crossbar and the surface prior to
attaching. The shorter screws goes in the sidebars. The
longer screws go into the crossbars. See Figure G.
IMPORTANT: supplied screws are designed to work with a
worksurface with a minimum thickness of 3/4”
Figure D– Sidebar Attachment
Xsede Height Adjust 3 Column
T-Leg
Installation Continued
Figure E– Spacing Bumpers
Figure G– Worksurface Attachment
Figure F– Power Supply Support
4 1/2”
4 1/2”
23”DEEP-(1 1/16”)
29”DEEP-(4 1/16”)
23”DEEP-(1 1/16”)
29”DEEP-(4 1/16”)
#8 X 5/8”Panhead Woodsc rews
#10 x 2 1/4”Flathead

XSEDE® Height Adjust
3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Customer Care.
Part 3111703,-
Assembly Instructions
6. Attach the handset to front edge of the worksurface using in-
cluded #8 X 5/8” Panhead Wood Screws. Connect the
cables and power supply. Use Cable Ties to secure
wiring to base. Ensure no cables are hanging down.
See Figure H.
Figure H– Electrical Assembly
Xsede Height Adjust 3 Column
T-Leg
Installation Continued
Warning leaflet and user manual should be
Warning Leaflet Electric User Manual