Kospel SP180 User instructions

Domestic Hot Water Cylinder
SP180
ZBIORNIK BUFOROWY
Assembly and operating manual

2
Safety instructions
1. Readandstrictlyfollowthisinstallationandoperatinginstructionstoensurea
longlifeandreliablecylinderoperation.
2. Themanufacturerofthiscylinderwillnotbeliableforanydamagesduetothe
failuretofollowtheinstallationandoperationinstructions.
3. Thecylindermustnotbeinstalledinroomswherethetemperaturemaydrop
below0°C.
4. The cylinder’s installation and the initial start-up, as well as all electrical and
hydraulicworkmustbeperformedbyaqualiedprofessionalinstaller.
5. The cylinder is designed for standing vertical installation- screw on feet or
wall-hung installation (after purchasing an appropriate hanger from KOSPEL
company),eitherhorizontallyorvertically.
6. Mountingofthedeviceinawall-hungpositionshouldbedoneonthewallwith
sufcientcarryingcapacity.Fulltank’sweight:250kg.
7. Thedevicemustbeinstalledinsuchaplaceandinsuchawayinordernotto
oodtheroomincaseoftheemergencywaterleak.
8. Connectionstowatersupplysystemandcentralheatingsystemmustbemade
inaccordancewiththediagraminthisinstallationinstruction.Failuretofollowthe
installationinstructioninvalidatethewarrantyandmaycausecylinder’sdamage.
9. Connectionstowatersupplysystemmustbemadeinaccordancewiththelegally
bindingstandards.
10. Thecylinderisapressureappliancedesignedforconnectiontothewatersupply
systemwherethewaterpressuredoesn’texceed0,6MPa.Ifthewaterpressure
exceeds0,6MPa,thepressurereducingvalvebeforecylindermustbetted.
11. Asmallleakfromthesafetyvalvethroughtheoutletpipemayoccur-itisanormal
operatingstateoftheappliance.Theoutletofthepipehastoremainopen.Do
notclogit,ascloggedoutletmaycauseabreakdownofthecylinder.
12. Donotusethecylinderifyoususpectthatthesafetyvalvemaybefaulty.
13. Thetankisequippedwithamagnesiumanode-anadditionalprotectionagainst
corrosion.Theanodeisanoperatingpart,therefore,itisexposedtowear.The
condition of the magnesium anode should be controlled every 12 months.
The anode must be replaced once every 18 months.
14. Ratedtemperatureofwaterinthecylindershouldnotexceed80°C.
Thecylinderissuitableforttinganimmersionheaterwiththermostate.g.GRW1.4,
GRW2.0.Theimmersionheatermustbettedinlieuofcork1½″.
Amaximumlengthofimmersionheater:400mm.

3
GB-062_f.850
Connection to the water system
Connectionto thewatersystemmust beperformedaccording tobindingnorms of
hydraulicinstallation.Thecylinderisapressureappliancedesignedforconnection
tothewatersupplysystemwherethewaterpressuredoesn’texceed0,6MPa.Ifthe
waterpressureexceeds0,6MPa,thepressurereducingvalvebeforecylindermust
betted.Pleasefollowthewaterconnectioninstructionsbelow:
- installtheT-connectionwith6barsafetyvalve(e.g.ZB-4)andthedrainvalveto
thettingofthecoldwaterinlet[ZW].It’sforbiddentoinstallacut-offvalve(or
anyowreducer)betweenthetankandthesafetyvalveandonitsoutlet.The
safetyvalvemustbeinstalledinsuchaplaceastoquicklyletyounoticethe
outgoingwater,
- installthecylinderequippedwiththesafetyvalvetothewatersystem,
- attached pipe (PEX-AL-PEX) must be properly screwed into one of the two
sockets3/4″acc.tothediagram‘SP180mountingoptions’
Sockets3/4″whicharelocatedintheupperpartoftheunitareintendedforcoldwater
inletandhotwateroutlet.
Eachcylinderisequippedwithttingfordomestichotwatercirculationconnection-1/2″.
WhenmountedintheverticalpositionPEX-AL-PEXpipecanbescrewedinanyofthe
3/4″sockets,however,ZW(coldwater)shouldbeledtothebottompartofthestorage
tank,whereasCW(hotwater)shouldbedeliveredfromupperpartsofthestorage.
WhenmountedinthehorizontalpositionPEX-AL-PEXpipemustbescrewedinthe
bottomsocketandZW(coldwater)inletshouldbeattachedtoit.

4
ZB ZW
Cylinder emptying
When mounted in vertical positions (connections up) in order to allow gravity
draining-drainingpipeshouldbeledtowardsthebottomofthestoragetank.

5
GB-062_f.850
ZW CW
CW
ZW
CW ZW
CW
ZW
ZG
PG
ZG
ZG
ZG
PG
PG
PG
sensor
pipe
circulation
ZW - coldwater
CW - hotwater
ZG - heatingmediumsupply
PG - heatingmediumreturn
SP180mountingoptions
PEX-AL-PEX
PEX-AL-PEX
PEX-AL-PEX
PEX-AL-PEX
Connection to the central heating system
Cylindermustbettedtothecentralheatingsystembypipeunions1″.Acut-offvalves
mustbeinstalledbeforethepipeunions.Aowrateofheatingwatermustbehigh
enoughtomaximisecylinder’sefciency(seetechnicaldatatable).Itconcernsthe
forcedcirculationinstallation(withacentralheatingwaterpump).

6
SP180construction
 [1] -upperlid
 [2] -thermalinsulation
 [3] -magnesiumanode
 [4] -sensorpipe
 [5] -connections(centralheating)
 [6] -coldwater
    (PEX-AL-PEXpipe)
 [7] -immersionheaterconnection
 [8] -lowerlid
 [9] -feet
 [10]-anode’sblank
 [11]-hangers-additionalequipment
 [12]-circulation
 [13]-hotwater
ø595
3
5
4
1
2
7
9
8
6
11
12
132
1364
1500
13
210
100
730
10
Start-up
Beforethestart-upmakesurethattheinstallationprocedureshavebeencarriedout
inaccordancewiththeregulationsincludedinthismanual.
Cylindermustbelledwithwater:
• turnonthevalveoncoldwatersupplypipe,
• turnonthehotwateroutletvalve(wateroutowwithouttheairbubblesindicates
thatthetankisfull),
• turnofftheoutletvalves,
• turnontheheatingmediumvalves,
• ventheatingcircuit-ifneedbe.
Checkforwaterandheatingmediumleaks.Checkoutthesafetyvalveperformance
inaccordancewithvalvemanufacturer’sinstruction.

7
GB-062_f.850
Operation
Followtheguidelinesbelowforsafetyandtrouble-freecylinderoperation:
• Checkout thesafetyvalveperformanceonce every14days. Donotusethe
cylinderifthewaterdoesnotcomeout(itindicatesthatthevalveisbroken).
• Cleaninsideofthecylinderperiodically.Thefrequencyofcleaningdependson
thedegreeofwaterhardness.Thecleaningshouldbedonebyaqualiedperson.
• Thewearconditionoftheanodemustbeinspectedannually.
• Theanodemustbereplacedonceevery18months.
- anoderodreplacement[3]:takeoffanode’sblank[10],takeoutaninsulation
ring,turnoffthecut-offvalveoncoldwatersupplypipe,turnonthehotwater
valve(mixertap),turnthedrainvalveon,drainasmuchwaterasyouneed
toeasilyunscrewtheanoderod(avoidingroomooding).Removethecork
andunscrewtheanoderod.
• Heatupthewaterabove70°Cperiodicallyforhygienereasons.
• Failuresormalfunctionsnotifytotheseller.
• Insulatetheoutletpipeandheatingcoilconnectionpipestominimisetheheat
loss(recommended).
Aboveactivitiesarebeyondofthescopeof warranty service (should be done by
theuser).
Technical data
Domestic Hot Water Cylinder SP180
Storagecapacity l 183
Ratedpressure storage MPa 0,6
jacket 0,3
Ratedtemperature °C 80
Capacity storage dm3140
jacket 43
Heattransfersurfacearea m21,6
Cylinder’spower80/10/45°C* kW 48
Cylinder’sefciency l/h 1200
Weight kg 75
MagnesiumanodeM8ø33 mm 450
*  heatingwatertemp./supplywatertemp./domesticwatertemperature;owrateofheatingwater
throughthecoil-2,5m3/h.

KOSPEL S.A. 75-136 Koszalin, ul. Olchowa 1
tel. [phone]
[email protected] www.kospel.pl