L.L.Bean MISSION CORNER ENTERTAINMENT STAND User manual

MISSION CORNER ENTERTAINMENT
STAND
Thank you for purchasing our Mission Corner Entertainment Stand. Assembly of this
product requires a Phillips screwdriver and a hammer. We have found it helpful to have
a second person present in at least one step of the assembly.
UG61082403

0UG61070427
STEP 1
Read through these instructions thoroughly before
beginning assembly. We have found this to be of great
value when first assembling this product.
STEP 2
Remove all parts and hardware from packing material.
Wooden pieces should be placed on a non-abrasive
surface (like the carton or carpet) to prevent damage to
the finish.
STEP 3
Identify all parts using diagram at right at
list below.
PARTS
Left Divider (A)
Right Divider (B)
Top (C)
(2) Shelf (D)
(2) Right Wing Shelf (E)
Right Base Wing Shelf (F)
Right Side Panel (G)
(2) Left Wing Shelf (H)
Left Base Wing Shelf (I)
Left Side Panel (J)
Back Panel (K)
STEP 4
Identify and count hardware using diagram at right.
Assembly of this product requires a Phillips
screwdriver and a hammer. We have found it
helpful to have a second person present in at least
one step of the assembly.
(28)

0UG61070427
STEP 5
Attach 6 cam pegs to the outside face of
Left Divider (A) and Right Divider (B)
as shown at right.
STEP 6
Lay Top (C) with cleats facing up on non-abrasive
surface (carpet or carton). Align predrilled holes in
Right Divider (B) with pilot holes in ends of middle
cleats on underside of Top (C). Ensure that the cam
pegs installed in Step 5 point away from the center
of the unit. Secure center side panel using two #8
screws. Do not tighten screws completely in order
to more easily install shelves in next few steps.
Note the relative positions of the FIVE pilot
holes in the rear edge of the Right Divider (B)
and the pilot holes in the cleat on the back edge of
the top.
STEP 7
Repeat Step 6 to attach other Left Divider (A) to
Top (C). Do not tighten screws completely in order
to more easily install shelves in next few steps.

0UG61070427
STEP 8
Have second person hold shelf (D) in place
between center Dividers. Align predrilled
holes in Left Divider (A) with pilot holes in
shelf cleats. Ensure that back panel pilot
holes in edge of shelf face back edge of the
Top (C). Secure using two #8 screws.
Repeat to Right Divider (B). Do not tighten
screws completely in order to more easily
install bottom shelf in next step.
STEP 9
Repeat Step 8 to attach second Shelf (D).
Ensure that back panel pilot holes in edge of
shelf face back edge of the Top (C). Secure
using four #8 screws.
STEP 10
Tighten all screws securely. Conceal front
screwholes using wood plugs as shown at
right. Tap plugs gently with hammer to
secure.

0UG61070427
STEP 11
Insert two camlocks into the underside of each Right Wing
Shelf (E) and Left Wing Shelf (H). Ensure that the arrow
on the face of the camlock ’points’to the hole in the edge of
the shelf. Press firmly into place.
There are two wing shelves for each side of the unit. They
can be distinguished by locating the pilot hole on the edge
of the shelf which will enable you to attach the side panel.
When the shelf is installed, the pilot hole will face the rear
of the unit as shown in Step 12.
STEP 12
Prepare Right Base Wing Shelf (F) and Left Base
Wing Shelf (I) for installation. Insert two camlocks
into the underside of each base wing shelf. Ensure
that the arrow on the face of the camlock ’points’to
the hole in the edge of the shelf. Press firmly into
place.
The base wing shelves have a cleat across the front
edge as well as a pilot hole for the attachment of the
side panel.
STEP 13
Attach first Left Wing Shelf (H) to Left Divider
(A). Align cam pegs in Left Divider (A) with holes
in edge of Left Wing Shelf (H). Ensure that pilot
holes in edge of shelf are visible from rear of unit
as shown. Secure first shelf by turning camlocks at
least 1/2 turn clockwise with Phillips screwdriver
before placing second shelf. Repeat for other Left
Wing Shelf (H).
STEP 14
Attach Left Base Wing Shelf (I) to Left Divider (A)
using same technique as in Step 13. Align cam pegs
in Left Divider (A) with holes in edge of Left Base
Wing shelf (I). Ensure that pilot hole in edge of
shelf is visible from rear of unit as shown and
that cleat is toward front of unit. Turn camlocks
at least 1/2 turn clockwise with Phillips screwdriver
to secure.

0UG61070427
STEP 15
Using same technique as in Step 13, attach first
Right Wing Shelf (E) to Right Divider (B) Repeat
for other Right Wing Shelf (E). Attach Right Base
Wing (F) to Right Divider (B) using same technique
as in Step 14.
STEP 16
Align predrilled holes in back support of Left
Divider (A) with pilot holes in edge of Left Side
Panel (J). Secure using two #8 screws.
Align predrilled holes in Left Side Panel (J) with
pilot holes in edges of Left Wing Shelves (H) and
Left Base Wing Shelf (I). Secure using one #8
screw for each shelf.
Tighten all screws securely.
STEP 17
Repeat using same technique as in Step 16 by
aligning predrilled holes in back support of Right
Divider (B) with pilot holes in edge of Right Side
Panel (G). Secure using two #8 screws.
Align predrilled holes in Right Side Panel (G) with
pilot holes in edges of Right Wing Shelves (E) and
Right Base Wing Shelf (F). Secure using one #8
screw for each shelf.
Tighten all screws securely.

0UG61070427
STEP 18
Align predrilled holes in Back Panel (K)
with pilot holes in cleat on back edge of
Top (C) and shelf (D). Secure using four
#8 screws. Tighten screws securely.
STEP 19
Conceal screw holes on side panels
using wood plugs. Tap plugs
gently with a hammer to seat them
firmly.
CARE
Dust as needed with a soft cloth. Clean with damp
cloth and mild solution of dish soap. Polish with
soft cloth and polish that contains no pigments or
silicone.
www.llbean.com
Product Support 1 800 341 4341