L.L.Bean ROUND ADIRONDACK TABLE User manual

ROUND ADIRONDACK TABLE
Thank you for purchasing this L.L.Bean Home Round
Adirondack Table. Assembly of this product requires a
7/16” wrench or an adjustable wrench, and Phillips
screwdriver. We have found it helpful to have a second
person assist with assembly.
930 0PH48090130

STEP 1
Read through these instructions thoroughly
before beginning assembly. We have
found this to be of great value when first
assembling this product.
STEP 2
Remove all parts and hardware from
packing material.Wooden pieces should
be placed on a non-abrasive surface (like
the carton or carpet) to prevent damage to
the finish.
STEP 3
Identify all parts using diagram at right
STEP 4
Identify and count hardware using diagram
at right.
Assembly of this product requires an
adjustable wrench and Phillips
screwdriver.We have found it helpful to
have a second person present in at least
one step of the assembly.
STEP 5
Locate two leg sections (B) with factory-
installed nut countersunk into them.
Attach outer leg (C) to inner leg (B) by
placing outer leg (C) on top of inner leg
(B) and inserting 1 ½” machine screw with
washer, through center hole in outer leg
(C) and into the factory-installed locknut
in the center of inner leg (B). Do not
tighten fully at this time. This will create
a “scissor” leg assembly.
Repeat for the other leg.

STEP 6
Attach the leg assembly from STEP 5 to
the top assembly (A) by inserting a
carriage bolt through the predrilled holes
in the leg supports on the underside of the
tabletop and through the leg assembly.
Add a washer and fasten with a locknut.
Repeat to other leg assembly.
Note: Use 2 ¾” carriage bolt for (B) leg
and use 2” carriage bolt for (C) leg.
Take care in aligning the legs on the
inward side of the leg support brackets,
which were factory mounted to allow for
the offset of the legs.
STEP 7
Connect the leg assemblies using leg
stretchers (D). Insert the 1 ½” screws
through the two small predrilled holes at
the base of each leg inward into the pilot
holes in the ends of each leg stretcher.
Note: You may now tighten the carriage
bolts fully and then tighten the machine
screws connecting the legs.

CARE
Thank you for choosing our classic L.L.Bean
Adirondack furniture. The natural,finished furniture
is made of solid oak and finished with a wood
preservative. This oak hardwood will gray slightly as
it ages. Painted furniture is made of maple hardwood
and finished with a rugged weather-resistant acrylic
paint. All of our Adirondack Furniture is made in the
United States.
Recommendations for extending the life of your
furniture:
•During inclement weather and off-season,
bring furniture indoors or use a furniture
cover.
•Over time, wood exposed to the ground
will absorb moisture, which may cause
rot. If you use this chair on a lawn,
occasionally move it to a dry surface
(patio or deck) to allow the legs to dry out.
•A deck, porch, or patio is the best location
for your furniture.
•To clean, wipe accumulated dirt with a
solution of warmsoapy water and a soft
cloth; rinse thoroughly with clean water.
Over time your Adirondack furniture will need
refinishing. We recommend the following:
•Lightly sand each piece with a fine grade of
sandpaper before applying paint or finish.
You do not have to sand down to bare wood.
•On painted furniture apply a primer first.
Finish with an outdoor weather resistant
acrylic paint. The original paint color can be
matched at your local hardware or paint
store.
•If you have solid oak furniture, sand and
finish with any high-grade wood
preservative.
www.llbean.com
Product Support 1 800 341 4341