L.L.Bean MISSION ENTERTAINMENT STAND User manual

MISSION ENTERTAINMENT STAND
Thank you for purchasing our Mission Entertainment Stand. Assembly of this
product requires a Phillips screwdriver and a hammer. We found it helpful to have
a second person assist with a couple of the steps.
7460 ATF7081230

STEP 1
Read through these instructions thoroughly before you
begin assembly. We have found this to be of great
value when first assembling this product.
STEP 2
Remove all parts and hardware from packing material.
Wooden pieces should be placed on a non-abrasive
surface (like the carton or carpet) to prevent damage
to the finish.
STEP 3
Identify all parts using diagram at right.
Removable Shelf (G)
STEP 4
Identify and count hardware using diagrams at right
and below.
(2) Door Pulls
(4) 5/8” Pan Screws
STEP 5
Stand the side assembly (A) on edge and attach floor
assembly (B) (floor assembly has groove on one face
and two wooden cleats on the other) with two 1-1/4”
#8 screws. Ensure that groove in floor assembly faces
inside of finished unit. Repeat to attach other side.
DO NOT TIGHTEN SCREWS AT THIS TIME.

STEP 6
Stand unit upright. Insert hinge pin into each predrilled
hole in front corner of bottom shelf and drop two
washers over each pin
STEP 7
Mount magnet catch in predrilled holes in underside
of shelf (D) using 1/2" #6 Pan screws provided.
(Underside of shelf has groove to accept back panel.)
STEP 8
Mount magnet plate to back of each door using 1/2"
#5 Flat screw.

STEP 9
Attach Door pulls by placing pulls through decorative
plates, then through door, securing with 5/8” pan
screws.
STEP 10
Slide back panel (C) into place in groove in bottom
assembly. Add shelf (D) to cabinet assembly by
aligning groove in underside of shelf over back panel
(C). Attach ONLY THE BACK EDGE of shelf (D) to
side assemblies (A) using one 1 1/4" #8 screw on each
side. This will enable you to pivot the shelf to install
the doors.
DO NOT FULLY TIGHTEN THE SCREWS.
We found it helpful to use one door to hold the shelf in
place as shown to right.
STEP 11
Insert one 1/8" x 1" steel hinge pin into predrilled hole
in top edge of each door. Pivot shelf (D) upward and
position left door so that predrilled hole in bottom edge
of Door (E) engages hinge pin and washers in left front
corner of floor assembly (B) installed in STEP 7.
Align hinge pins in top edge of door with predrilled
hole in underside of shelf (D). Drop shelf down to trap
door in place.

STEP 12 - a second person is helpful here.
Position right door so that predrilled hole in bottom
edge of Door (E) engages hinge pin and washers in
right front corner of floor assembly (B) installed in
STEP 7. Close both doors as fully as possible. Grasp
door handles with one hand and pivot shelf (D)
upward. Align hinge pins in top edge of door with
predrilled hole in underside of shelf (D). Drop shelf
down to trap doors. Insert two remaining 1 1/4" #8
screws through counter sunk holes in side assemblies
(A) to fix shelf in place.
DO NOT TIGHTEN SCREWS COMPLETELY.
STEP 13
Attach top assembly (F) to side assemblies (A) by
inserting 1 1/4" #8 screws through counter sunk holes
in side assemblies into pilot holes in the top assembly
supports.
STEP 14
Tighten ALL screws and tap in wood plugs with
hammer to conceal screws.

STEP 15
Insert the 4 shelf pins into the holes drilled in the
insides of Side Assemblies (A)
STEP 16
Install removable shelf (G) into cabinet by placing the
shelf onto the 4 shelf pins ensuring that they align with
and drop into the grooves in removable shelf (G).
CARE
Dust as needed with soft cloth. Clean with damp cloth
and mild solution of dish soap. Polish with soft cloth
and polish that contains no pigment or silicone.
www.llbean.com
Product Support 1 800 341 4341