Lattice Semiconductor mVision AR0234 User manual

QuickART
Lattice mVision AR0234 Sensor Board
This document provides a brief introduction to Lattice mVision AR0234 Sensor Board.
1
2
Check Kit Contents
The Lattice mVision AR0234 Sensor Board kit contains the following items:
OnSemi AR0234 Sensor Module with adapter cable for EVDK
Quick Start Guide
Preparing the Hardware and Running the Demonstration
Before starting the evaluation, please have the following items available and ready to
use on the test bench. Follow the steps below to prepare the hardware before applying
power.
Embedded Vision Development Kit (EVDK) with camera modules removed.
Lattice mVision AR0234 Sensor Board with lens holder and lens assembled.
2 jumpers placed on J7 and J8 headers of AR0234 Sensor Board.
Connect the EVDK and AR0234 Sensor Board together using the Flex Cable as
shown below.
Camera, lens and holder
Power (3.3 V) Control, Power &
MIPI (from EVDK)
IR_CUT
Motor
Control
IR_CUT
Motor Flash & Shutter
Control
Power
(2.8 V)
Power
(1.8 V)

Lattice mVision AR0234 Sensor Board
3
4
Run the Demonstration
Apply power to the ECP5 VIP Processor Board using 12 V adaptor.
Connect jumpers to the Crosslink and ECP boards as follows:
Done!
Apply power to the ECP5 VIP Processor Board using 12 V adaptor. Congratulations! You
have successfully demonstrated the hardware setup and programming procedure for
testing the operation of AR0234 Sensor Board using Lattice EVDK. To learn more about
these solutions and download full documentation for this kit, including schematics for all
the boards, visit the Lattice website at: www.latticesemi.com/mVision-AR0234-board
Connect HDMI monitor to the board using HDMI cable.
Toggle the button “SW3 (SYS_RST)” on Crosslink VIP Bridge Board.
Sensor captured video will be displayed on the HDMI monitor.
Additional Terms and Conditions Applicable to Lattice Programming and Development Hardware
Lattice device programmers, programming cables, socket adapters, and other hardware sold for use in conjunction with Lattice
software (“Programming Hardware”) and Lattice evaluation boards and development kits sold for use in conjunction with
evaluating Lattice products (“Development Hardware”) are designed and intended for use solely with semiconductor components
manufactured by Lattice Semiconductor Corporation. Programming and Development Hardware is warranted to meet Lattice
specications only for a period of ninety (90) days; in all other respects the terms and conditions of sale of Programming and
Development Hardware shall be Lattice’s standard terms and conditions set forth in Lattice’s Sales Order Acknowledgment.
Additionally, Lattice specications for Programming and Development Hardware limit their use to low-volume engineering
applications only, and not for volume production use. The warranty for Programming and Development Hardware will not apply to
any Programming or Development Hardware used in production, used with worn or improperly installed hardware, or used with
incompatible systems or components.
CrossLink VIP Input Bridge Board
Jumper Name Description
J4 Short
J30 Open
J2 Short
-All other headers
should be kept open
AR0234 Sensor Board
Jumper Name Description
J7 Short
J8 Short
AR0234 Sensor Board
Jumper Name Description
J55 2-3
J51 1-2
J5 1-2
J9 1-2
J6 1-2
J3 1-2, 5-6
J50 1-2, 5-6
J7 2-3
J52 1-2 (SPI), 2-3 (JTAG)
J53 1-2
-All other headers
should be kept open
Technical Support
www.latticesemi.com/support
Copyright © 2022 Lattice Semiconductor Corporation. Lattice Semiconductor, L (stylized) Lattice Semiconductor Corp., Lattice
(design) are either registered trademarks or trademarks of Lattice Semiconductor Corporation in the United States and/or other
countries. Other product names used in this publication are for identication purposes only and may be trademarks of their
respective companies.
QS065 V1
January 2022