LAZBOY 45316A User manual

Big & Tall Executive Chair
ASSEMBLY
Instructions
Model: 45316A / 45316B

Should you prefer to
speak with a customer
service representative,
you may call toll free :
1-855-372-2315
0-800-051-6775
U.S. 6am - 5pm PST,
U.K. 2pm -1am
2

FAILURE TO FOLLOW THESE WARNINGS
WHEN IN USE COULD RESULT IN INJURY
• Do not stand on the item or use as a step ladder
• The piece has been tested and approved for users
weighing up to 350lbs (159 kg) per seat.
• Do not use this item unless all bolts and screws are
firmly secured and fastened.
• Check all bolts and screws every 90 days. As
necessary tighten if any are loose.
• Lift up then move. Pushing over or dragging this
product can result in an injury or cause damage to
the floor and piece.
3
Guidelines

Please read through this instruction booklet before
beginning assembly of this item.
Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all
parts on Parts List, extra room will allow you to
easily determine if all the pieces are present.
• Save all packing materials until assembly is
complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children
and pets until fully assembled.
• Please check for any loose screws and tighten them
before you use.
WARNING :DO NOT LET
CHILDREN PLAY IN OR
AROUND THE UNIT DUE
TO THE POSSIBLE RISK
OF INJURY.
4
Pre-Assembly Preparation:

5
Parts List
Casters Star BaseGas Liftwith Telescoping Cover Seat Plate
D
C
BA
1” Screws
1-3/4” Screws1-1/4” Screws
K
I
J
Allen Key M5
O
D1
D2
SeatCushion Back Cushion
G
F
Plastic Shroud
H
Quantity: 5 Quantity: 1 Quantity: 1 Quantity: 1
Quantity:1 Quantity: 1 Quantity: 1
Quantity: 1
Quantity: 2
Quantity: 2 Quantity:4Quantity: 4
L
1-1/4” Screws with Spring Washers
Left Arm
Quantity:1
E1
E2
M1
N1
N2
M2
Right Arm
Quantity:1
Quantity:2
Arm Inserts
Quantity:2
Arm Inserts
MN

Step 1 Step 2
Place the Star Base (B) upside down and insert 5 Casters (A) into the holes
on the Star Base (B).
Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover
(C) through the center hole on top of Star Base (B).
6
B
A
B
C

Step 3
Step 4
Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the
front of the seat plate facing the front of seat cushion). Attach by using
1-3/4” Screws (J) for the front holes of the Seat Plate (D) and 1” Screws
(I) for the rear holes of the Seat Plate (D) and tighten screws.
*Note: Tighten the screws completely.
Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever
receivers on the underside of Seat Cushion (F). Push down the key on
the receivers to pull out the levers.
*Note: Fix the cable for the seat plate into the plastic clips attached to
the bottom of the seat cushion.
Insert
Assemble t he lever
Push
Disassemble t he lever
7
I
J
F
D1
D2
F
D
D
O

Step 5
Step 6
Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the
back support plate over the Seat Plate (D) with 1-1/4” Screws (K).
*Note: Do not tighten the screws completely.
Insert 1-1/4" Screws with Spring Washers (L) into arm holes attaching
Arms (E1 & E2) (with the front of arms facing the front of seat cushion)
to sides of Seat Cushion (F) and Back Cushion (G).
*Note: Tighten all the screws completely. Remember to
tighten the back support plate screws.
8
O
F
G
O
E2
E1
F
G
D
K
L

Step 7
Step 8
Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of
plastic shroud facing the front of seat cushion). Align shroud posts to
holes on bottom of Seat Cushion (F) and press into position.
Position the assembled chair upright with the seat plate facing down.
Insert the Gas Lift with Telescoping Cover (C) into the center hole of the
Seat Plate (D).
9
D
C
F
H
F
D

Step 9
Once all screws have been tightened, place the Arm Inserts (M1 & M2
& N1 & N2) into arm grooves.
10
M2
M1
N2
N1