LEGRAND HPM LLF024K1200 User manual

1200mm
100mm
37mm
Blade LED Batten
Instruction Manual
Cat No. LLF024K1200
1 Specifications
Cat No LLF024K1200
Lumen package 3600 lm
CCT 4000K
Supply Voltage 230-240V ~ 50Hz
Input Power 36W
Efcacy 100 lm/W
Input Current 0.15A
Power Factor 0.97
Colour Rendering Index (CRI) 80+
Beam Angle 108˚
Lifespan 35,000hrs @ 25˚C Ambient
Dimming Non-Dimmable
Warranty 3 YRS
2 Installation
FOR INDOOR USE ONLY
Isolate 240V mains supply before opening tting for maintenance or installation.
Follow the steps below:
1. Remove End Cap by pushing it outward (A-1). Only end with direction arrow should be opened.
2. Remove diffuser by sliding it towards the open end (A-2).
3. Insert mains wiring through grommet (A-2).
4. Fix the Luminaire body onto the wall/ceiling with screws and lugs provided (A-2).
5. Connect the Active, Neutral and Earths supply wires to the terminal block as shown (Fig. B).
6. Ensure terminal cover in installed with screw provided (Fig. B).
7. Assemble reector and end Cap (Fig. C).
8. DO NOT MEGGER TEST.
0
30
60
90-90
-60
-30
UNIT:cd
C0 /180
UNIT:cdUNIT:cdUNIT:cd
C90 /270
AVERAGE BEAM ANGLE (50%):107.6 DEG
0
300
600
900
1200
1500

Warranty
Legrand warrants this product for a period of 3 years from the date of purchase.
These goods come with guarantees that cannot be excluded under the Australian
and New Zealand Consumer Laws. You are entitled to a replacement or a refund for
a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
See the Warranty card enclosed with this product for further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
LE10393AAA LEG1778_B
1. This product must be installed and used as per these instructions.
2. The mounting screws on this product should be tightened to a maximum torque of 0.8Nm. Over tightening may damage the product.
3. This product contains no serviceable parts and no attempt should be made to repair this product. If the product is faulty it should be discarded.
4. This product is not suitable for installation in hazardous and/or corrosive areas.
5. Electrical installations periodically receive transient over voltages. This product has been designed to minimise the effect of such voltages on connected
equipment. It may not give full protection for extreme over-voltage transients such as those resulting from a close lighting strike.
6. This product utilises intellectual property in the form of registered designs, trademarks, and/or patents. Such intellectual property remains the property
of Legrand in all cases.
7. Legrand reserves the right to modify the specication of this product at any time.
8. This product has been designed to operate in ambient temperatures: -5°C to 25°C occasionally reaching 35°C.
9. Stated lifespan is an average. Actual lifespan will vary according to individual circumstances.
10. Extended exposure to UV rays (such as exposure to direct sunlight) may cause discolouration of this product.
11. The material in this product may vary in colour from batch to batch. Colour matching from one batch to another cannot be guaranteed.
Legrand Australia
1300 369 777
www.hpm.com.au
Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
2 Installation (cont.)
3 Maintenance/cleaning
This product should only be cleaned with a damp cloth. Cleaning agents and solvents should not be used.
4 Disclaimers
OFF
ON