Liko Golvo 9000 Series User manual

In this document, the person being lied is referred to as the paent, and the person helping them is referred to
as the caregiver.
Product Descripon
Golvo 9000 LowBase
Golvo 9000
QRG
Golvo 9000 mobile lis have a unique design, available
in two models. Both models are an excellent aid for daily
transfer of adults and children.
The LowBase model has extra low base for use in
combinaon with bed frames or other equipment where
space for the li base is limited.
Individual ng of Liko slings and other Liko liing
accessories to meet the paent need is of the utmost
importance for opmal performance and safety when using
the li.
Golvo™ 9000
mobile li
Instrucons for Use
Golvo 9000 Prod. No. 2000045
Golvo 9000 LowBase Prod. No. 2000049
7EN140108 Rev. 4
ENGLISH 2020
QRG
IMPORTANT!
Liing and transferring a paent always involves a certain level of risk. Read the instrucons for use for both the paent li and
liing accessories before use. It is important to completely understand the contents of the instrucons for use. The equipment
should only be used by trained personnel. Ensure that the liing accessories are suitable for the li used. Exercise care and cauon
during use. As a caregiver, you are always responsible for the paent’s safety. You must be aware of the paent’s ability to make it
through the liing situaon. If something is unclear, contact the manufacturer or supplier.

2www.hillrom.com
7EN140108 Rev. 4 • 2020
Table of Contents
Symbol Descripon .......................................................................................................................... 3
Safety Instrucons ........................................................................................................................... 4
Denions ....................................................................................................................................... 5
Technical Data ................................................................................................................................. 5
Dimensions ....................................................................................................................................... 6
EMC Table ......................................................................................................................................... 7
Assembly .......................................................................................................................................... 9
Disassembly .................................................................................................................................... 12
Operaon ....................................................................................................................................... 12
Charging the Baeries .................................................................................................................. 18
Maximum Load ............................................................................................................................... 19
Recommended Liing Accessories ................................................................................................. 19
Recycling Instrucons ..................................................................................................................... 21
Simple Troubleshoong .................................................................................................................. 22
Cleaning and Disinfecon .............................................................................................................. 23
Inspecon and Maintenance ......................................................................................................... 25

3www.hillrom.com 7EN140108 Rev. 4 • 2020
Symbol Descripon
These symbols can be found in this document and/or on the product.
Symbol Descripon
For indoor use only.
The product has extra protecon against electric shock (Insulaon Class II).
Protecon level against electric shock Type B.
Warning; this situaon requires extra care and aenon.
Read instrucons for use before use.
CE-mark.
IP N1 N 2 Protecon level against: ingress of solid objects (N1) and ingress of water (N2).
Legal Manufacturer.
Date of manufacture.
Cauon! consult instrucons for use.
Read instrucons for use before use.
Baery.
,
Pb
,
All baeries in this product must be recycled separately.
- Pb underneath the symbol indicate baeries containing lead
- Single Black line underneath the symbol indicate this product have been placed on the market aer 2005.
UL Recognized Component Mark for Canada and the United States.
EFUP, Environmental Friendly Usage Period (years).
Environmentally-friendly product which can be recycled and reused.
The Australian Safety/EMC.
PSE Mark (Japan).
Product Idener.
Serial Number.
Medical Device.
Recyclable.
The safety and essenal performance of medical electrical equipment.
Proof of Product compliance to North American safety standards.
Non-ionizing electromagnec radiaon.
X%
Y% ≤Tmin
Duty cycle for non-connuous operaon.
The maximum acve operaon me X% of any given me unit, followed by a deacvaon me, Y%.
The acve operaon me shall not exceed the specied me in minutes, T.
GS1 Data Matrix Barcode that may contain following informaon
(01) Global Trade Item Number
(11) Producon Date
(21) Serial Number
(01) 0100887761997127
(11) Y Y MM D D
(21) 012345678910

4www.hillrom.com
7EN140108 Rev. 4 • 2020
Before use, make sure that:
• the li is assembled in accordance with the assembly instrucons;
• the liing accessories are properly aached to the li;
• the baery has been charged for at least 6 hours;
• you have read the instrucons for use for the li and liing accessories;
• personnel using the li are informed of the correct operaon and use of the li.
Before liing, always make sure that:
• the liing accessory is selected appropriately, in terms of type, size, material and design, with regard to the paent’s needs;
• the liing accessories are not damaged;
• the liing accessories are correctly aached to the li;
• the li strap is not twisted or worn and can move in and out of the li;
• the liing accessories hangs vercally and can move freely;
• the liing accessory is correctly and safely applied to the paent in order to prevent injuries;
• the sling bar latches are intact. Missing or damaged latches must always be replaced with new ones;
• the sling’s strap loops are correctly connected to the sling bar hooks when the sling straps are extended
but before the paent is lied from the underlying surface.
Incorrect aachment of sling to slingbar may cause severe injury to the paent.
Prod. No. 2000045 and 2000049 have been tested by an accredited tesng instute
No modicaon of this product is allowed.
Use of this equipment adjecent to other equipment should be avoided because it could result in improper operaon, if such
use is neccessary, observe and verify that other equipment are operang normally.
Parcular care must be observed when using strong sources of potenal disturbance, such as diathermy, etc, so
that diathermy cables are not posioned on or near the li. If you have quesons, please consult the responsible
assisve device technician or the supplier.
The li may not be used in areas where ammable mixtures may occur, for example, in areas where ammable
goods are stored.
Safety Instrucons
Unbalanced liing poses a pping risk and may damage the li equipment!
Never leave a paent unaended during a liing situaon!
This Cauon noce is found on the Baery:
CAUTION! NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL
DO NOT SHORT CIRCUIT
USE THE SPECIFIED CHARGER ONLY
MAY EXPLODE IF DISPOSED IN FIRE
This Cauon noce is found on the Control box:
CAUTION! NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL
Intended use
Transferring paents (adult or children) between devices (e.g., within the room), oor liing, horizontal liing, supporng
paent limbs, ambulang paent, bathing paent, toileng paent, weighing paent and transferring paents from car.
Intended for use in following environments: health care, intensive care, emergency ward, rehabilitaon, habilitaon.
This product is not intended to be used by the paent alone. Liing and transferring a paent shall always be performed
with the assistance of at least one caregiver. This product is used as a means to perform the li but is not in contact with the
paent; therefore we do not discuss or describe various paent condions in this instrucon for use. Contact your Hill-Rom
representave for support and advice.
Certain environments and condions can limit the correct us of the mobile lis, including:
Thresholds, unlevel oor surfaces, various obstacles, and extra-thick carpets. These environments and condions can cause the
wheels of the mobile li not to roll as intended, possible imbalance in the mobile li, and increased exeron by the caregiver. If
you are uncertain that your care environment fullls the requirements for correct use of the mobile li, please contact your Hill-
Rom representave for further advice and assistance.

5www.hillrom.com 7EN140108 Rev. 4 • 2020
1. Li Strap
2. Sling bar with latches
3. Retractable armrests
4. Parking panel for sling bar
5. Oponal; Quick reference guide
6. Oponal: Holder for Quick Reference Guide
7. Product decal
8. Mast with inbuilt motor
9. Front wheels
10. Base
11. Rear wheels with brakes
12. Motor for base-width adjustment
13. Control box with;
Emergency stop
Electrical Emergency Lowering
Electrical Emergency liing
Baery charger indicators
Informaon display
14. Baery
15. Hand control
16. Handles
17. Emergency Lowering (mechanical)
18. Li arm
19. Extra low base (Golvo LowBase)
Denions
Forward direcon
Protected by Patent
Technical Data
Maximum load: 200 kg (440 lbs)
Please note: The base width may be adjusted
with weight up to 140 kg ( 308 lbs).
Material: Anodized aluminium
Weight: 9000: 38,8 kg kg (83,3 lbs)
9000 LowBase: 42,2 kg (93,0 lbs)
Heaviest removable part:
9000: 23,4 kg (51,6 lbs)
9000 LowBase: 23,4 kg (51,6 lbs)
Wheels: Front: 75 mm* (3 in) twin wheels.
*LowBase: 46 mm (1.8 in) twin wheels.
Rear: 75 mm (3 in) twin wheels with brakes.
Turning diameter Golvo 9000: 1330 mm (52 in)
Golvo 9000 LowBase: 1330 mm (52 in)
Emergency
lowering device: Mechanical and electrical
Liing Speed (no
load)
37 mm/s (1.5 in/s) or
27 mm/s ( 1.1 In/s)
Liing interval: 1245 mm (49 in) (height-adjustable)
Sound level: 52.8 dB(A)
Protecon class: IP X4
Operang forces,
controls: Hand control: 5 N
Electrical data: 24 V
Intermient
power: Int. Op 10/90, acve operaon max 2 min.
Only 10% of a given length of me may be
acve, but no more than 2 min.
Baery opons: Lead-acid gel, valve-regulated baery
24 V 2.9 Ah Prod. No. 2006106.
2,8 kg (6.2 Ibs.)
Li-ION baery
25.6 V, 3.3 Ah Prod. No. 2006110.
1,4 kg (3.1 Ibs.)
New baeries provided by supplier!
Baery charger: Internal charger, 100-240 V AC, 50-60 Hz,
max 400 mA.
Li motor:24 V, 7.5 A
Base motor 24 V, 5.5 A
Surrounding
funconal
environment:
Temperature: +10°C to +40°C, (50° F to 104° F)
Humidity: 20% to 80% at 30°C non-condensing,
Atmospheric pressure: 700hPa to 1060hPa.
Golvo 9000 LowBase
19
QRG
12
13
10
11
15
14
16
17
18
BATTERY
ON CHARGE
Forward direcon
5
1
3
2
9
8
7
4
6
Golvo 9000
The device is intended for use indoors
Type B, in accordance with the electrical shock
protecon class.
Class II equipment.

6www.hillrom.com
7EN140108 Rev. 4 • 2020
The liing interval 1245 mm (49 in) is height-adjustable, see ”Li strap adjustment”, Operaon chapter.
Note: When changing to other liing accessories check that the li sll achieves desired liing height.
* Reference measurement according to Standard EN ISO 10535:2006
Dimensions
Measurements in mm / in
Measurements
Lateral view
M
Lmax
A
E
B
B1
B3
B2
O
GE
F1 F
Lmin
Maximum
reach
Top view
D2
C
D
Golvo 9000 LowBase
B4
Model
A
BB1 B2 B3* B4
CD
D2* E F F1 G Lmax Lmin M O
max. min. max. min. max. min.
Golvo 9000 2090 1455 1185 870 480 480 -1020 735 907 623 01100 105 25 940 1816 571 436 391
Golvo 9000
LowBase 2090 1455 1185 870 480 480 600 1028 745 907 623 01100 60 / 105 22 940 1816 571 436 391
Model ABB1 B2 B3* B4
CDD2* E F F1 G Lmax Lmin M O
max. min. max. min. max. min.
Golvo 9000 82.3 57.3 46.6 34.2 18.9 18.9 -40.2 28.9 35.7 623 043.3 4.1 1.0 37 71.5 22.5 17.2 15.4
Golvo
9000 Low-
Base
82.3 57.3 46.6 34.2 18.9 18.9 23.6 40.5 29.3 35.7 623 043.3 2.4 /
4.1 0.9 37 71.5 22.5 17.2 15.4
**600 mm (24 in)
**700 mm (28 in)
Golvo 9000 Golvo 9000
Lateral view

7www.hillrom.com 7EN140108 Rev. 4 • 2020
EMC Table
Guidance and manufacturer’s declaraon – electromagnec emissions
The mobile li is intended for use in the electromagnec environment specied below. The customer or the user of the
mobile li should assure that it is used in such an environment.
”Essenal performance according to the manufacturer: The hoist shall not move unintenonally while being submied to
disturbances.”
Emissions test Compliance Electromagnec environment - guidance
RF emissions
CISPR 11
Group 1 The mobile li uses RF energy only for its internal funcon.
Therefore, its RF emissions are very low and are not likely to
cause any interference in nearby electronic equipment.
RF emissions
CISPR 11
Class B
The mobile li is suitable for use in all establishments inclu-
ding domesc establishments and those directly connected
to the public low-voltage power supply network that supplies
buildings used for domesc purposes.
Harmonic emissions
IEC 61000-3-2
Complies
Voltage uctuaons/ icker emis-
sions
IEC 61000-3-3
Complies
Guidance and manufacturer’s declaraon – electromagnec immunity
The mobile li is intended for use in the electromagnec environment specied below. The customer or the user of the
mobile li should assure that it is used in such an environment.
”Essenal performance according to the manufacturer: The hoist shall not move unintenonally while being submied to
disturbances.”
Immunity test IEC 60601 test level Compliance level Electromagnec
environment - guidance
Electrostac
discharge (ESD)
IEC 61000-4-2
+/- 8 kV contact
+/- 15 kV air
+/- 8 kV contact
+/- 15 kV air
+/- 8 kV contact
+/- 15 kV air
Floors should be wood, concrete or
ceramic le. If oors are covered
with synthec material, the relave
humidity should be at least 30 %.
Electrical fast
transient / Burst
IEC 61000-4-4
+/- 2 kV for power supply
lines
+/- 1 kV for input/output
lines
+/- 2 kV for power supply
lines
n/a. for input/output lines
Mains power quality should be that
of a typical commercial or hospital
environment.
Surge
IEC 61000-4-5
+/- 1 kV dierenal mode
+/- 2 kV common mode
+/- 1 kV dierenal mode
n/a. for common mode
Mains power quality should be that
of a typical commercial or hospital
environment.
Voltage dips, short inter-
rupons and voltage va-
riaons on power supply
input lines
IEC 61000-4-11
0 % UT for 0,5 cycle, at 0, 45,
90, 135, 180, 225, 270 and
315 degrees
0 % UT for 1 cycle, at 0
degrees
70 % UT for 25 cycles at 50
Hz and 30 cycles at 60 Hz, at
0 degrees
0 % UT for 250 cycles at 50
Hz and 300 cycles at 60 Hz.
0 % UT for 0,5 cycle, at 0,
45, 90, 135, 180, 225, 270
and 315 degrees
0 % UT for 1 cycle, at 0
degrees
70 % UT for 25 cycles at 50
Hz and 30 cycles at 60 Hz,
at 0 degrees
0 % UT for 250 cycles at 50
Hz and 300 cycles at 60 Hz.
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of the
[Equipment or System] requires
connued operaon during power
mains interrupons, it is recom-
mended that the [Equipment or Sys-
tem] be powered from an uninter-
rupble power supply or baery.
Power frequency (50/60
Hz) magnec eld
IEC 61000-4-8
30 A/m Complies Power frequency magnec elds
should be at levels characterisc of
a typical locaon in a typical com-
mercial or hospital environment
NOTE UT is the a.c. mains voltage prior to applicaon of the test level.

8www.hillrom.com
7EN140108 Rev. 4 • 2020
Guidance and manufacturer’s declaraon – electromagnec immunity
The mobile li is intended for use in the electromagnec environment specied below. The customer or the user of the
mobile li should assure that it is used in such an environment.
”Essenal performance according to the manufacturer: The hoist shall not move unintenonally while being submied to
disturbances.”
Immunity test IEC 60601 test level Compliance level Electromagnec environment - guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
6 Vmrs
150 kHz to 80 MHz
10 V/m
80MHz to 2,7GHz
6 Vmrs
10 V/m
Portable and mobile RF communicaons
equipment should be used no closer to any
part of the mobile li, including cables, than
the recommended separaon distance cal-
culated from the equaon applicable to the
frequency of the transmier.
Recommended separaon distance
Pd 2,1=
Pd 2,1= 80 MHz to 800 MHz
Pd 3,2=800 MHz to 2,7 GHz
where P is the maximum output power rang
of the transmier in was (W) according to
the transmier manufacturer and d is the
recommended separaon distance in meters
(m).
Field strengths from xed RF transmiers, as
determined by an electromagnec site survey,
a should be less than the compliance level in
each frequency range. b
Interference may occur in the vicinity of
equipment marked with the following symbol.
NOTE 1 At 80MHz and 800MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situaons. Electromagnec propagaon is aected by absorpon and reec-
ted from structures, objects and people.
a Field strengths from xed transmiers, such as base staons for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theorecally with accuracy. To
assess the electromagnec environment due to xed RF transmiers, an electromagnec site survey should be considered.
If the measured eld strength in the locaon in which the Golvo™ 9000 li is used exceeds the applicable RF compliance
level above, the mobile li should be observed to verify normal operaon. If abnormal performance is observed, addional
measures may be necessary, such as reorienng or relocang the mobile li.
b Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 10 V/m.

9www.hillrom.com 7EN140108 Rev. 4 • 2020
Recommended separaon distances between portable and mobile RF
communicaons equipment and the mobile li
The mobile li is intended for use in an electromagnec environment in which radiated RF disturbances are controlled. The
customer or the user of the mobile li can help prevent electromagnec interference by maintaining a minimum distance
between portable and mobile RF communicaons equipment (transmiers) and the mobile li as recommended below,
according to the maximum output power of the communicaons equipment.
Rated maximum output
power of transmier
(W)
Separaon distance according to frequency of transmier
(m)
150 kHz to 80 MHz
Pd 2,1=
80 MHz to 800 MHz
Pd 2,1=
800 MHz to 2.7 GHz
Pd 3,2=
0.01 0,12 0,12 0,24
0.1 0,38 0,38 0,73
1 1,2 1,2 2,3
10 3,8 3,8 7,3
100 12 12 23
For transmiers rated at a maximum output power not listed above, the recommended separaon distance d in meters (m)
can be esmated using the equaon applicable to the frequency of the transmier, where P is the maximum output power
rang of the transmier in was (W) according to the transmier manufacturer.
Note 1: At 80 MHz and 800 MHz, the separaon distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situaons. Electromagnec propagaon is aected by absorpon and reec-
on from structures, objects and people.
• Li mast with control box and hand control, sling bar with
latches, 2 M6 screws
• Armrest
• Base, with width adjustment motor
Lock the wheels on the base before starng to assemble the li.
2. Screw the two provided M6 screws into the upper
holes on the li mast.
No screws in the lower holes!
1. A) Posion the li mast between the two black plasc plugs on
the base cross member.
B) Then push the mast forwards as in the gure above so that
it hooks onto the cross member.
Assembly
Before assembly, make sure you have the following parts and tools:
• Baery
• Tools: 4, 5 mm hex keys
• Bag containing: charger cable, charger connector cable
• Instrucons for use
A
B

10 www.hillrom.com
7EN140108 Rev. 4 • 2020
3. A) Place the armrest part in the aachment on the li mast,
starng with the lower groove.
B) Lower and load the armrest unl it hooks onto the upper
groove on the armrest part. Do not remove any of the
pre-assembled M8 screws completely, but it may be
necessary to loosen them.
4. Secure the armrest by ghtening the two
pre-assembled M8 screws.
A
B
8. Oponal accessories:
Quick reference guide to be
placed in Holder for Quick
reference guide on the mast.
7. Hang the hand control on the
handle.
Motor for base
adjustment.
Li motor
Hand control
6. Connect the baery and secure it to the control box bracket.
A click sound can be heard when the baery is installed correctly.
5. Connect cables to the control box,
see illustraon. Make sure plugs are
fully seated.
9. Reset the emergency stop by
turning the buon clockwise.
ON CHARGE
BATTERY
kg/lbs
kg/lbs

11 www.hillrom.com 7EN140108 Rev. 4 • 2020
Aer assembly and charging, ensure that:
• The moon of the li arm corresponds to the buons on the hand control/operaon panel.
• The emergency lowering funcons are working
(mechanical and electrical).
• The wheel brakes are working.
• The base-width adjustment works.
•The baery is fully charged.
• service interval is acvated! Push following buons on the handcontrol simultaneously:
Up / Down , unl a audio signal (single beep) is heard = service interval acvated.
(Alternavely use the push buons simultaneously for emergency liing up and down on the control box)
11. Place the charger cable on the
hook provided on the mast aer
completed charging.
10. A) Connect the extension cable for the charging cable to the control box.
B) Insert the extension cable in the tension clip underneath the control box.
C) Connect the charging cable to the extension cable.
IMPORTANT! Always charge the baery before using the li the rst me.
Charge the baery unl charging is completed, see "Charging the Baery" for
more informaon and instrucons.
AB C
ON CHARGE
BATTERY

12 www.hillrom.com
7EN140108 Rev. 4 • 2020
Disassembly
1. Begin by removing the sling bar or other accessory that is ed to the li.
2. Remove the armrest holder as described below:
A. Do not remove, just loosen the two M8 screws in the
armrest holder on either side of the li mast.
B. Remove the armrest holder using two screwdrivers.
Place screwdrivers inside on top of handlebar and pull up
simultaneously as illustrated.
3. Loosen the cables from the control box, see assembly, Remove the mast as described below:
A. Unscrew both the safety screws in the upper holes on the
mast.
B. Then screw the safety screws into the lower holes on the
li mast. This releases the mast from the base, and it can
now be removed.
When the mast has been detached from the base, it must be supported to prevent it from falling.
Operaon
Handcontrol operaon and indicators
Operate the li using the push buons on the handcontrol. For raising and
lowering: Direconal arrows show the direcon of movement (up/down)
The liing and base movement stops as soon as the push buon is released.
Indicator: 1 - 4
1 - Overload (Kg/Ibs) light "ashes yellow", too much load is applied to the li.
2 - Green light, baery power (100 - 50 %), Ok!
- will constantly light up green when charger is connected to mains.
3 - Yellow light, baery power (50 - 25 %), baery needs charging
4 - Yellow light, baery power (Less than 25 %), baery needs charging.
A buzzer will sound when pressing a push buon.
Note! If the buzzer sound starts during an ongoing li complete the li
and charge the li aerwards!
4 - Light "ashes yellow" and a buzzer will sound when pressing a push buon.
Charge the li immediately! The remaining baery power can only make
the li arm go down.
Note! Please see chapter "Charging the Baery" for more informaon.
Cable
Push buons:
Li arm:
Up / Down
Li arm (low speed):
Up / Down
Push buons:
Base width:
Out
In
kg/lbs
Indicator: 1 - 4
kg/lbs
2
3
4
1

13 www.hillrom.com 7EN140108 Rev. 4 • 2020
Control Box operaon and informaon
1. Emergency Stop buon
- Acvate: Push the red buon
- Reset: Turn the red buon clockwise.
2. UP (Arrow), Electrical emergency liing.
3. DOWN (Arrow), Electrical emergency lowering.
Operaon of the push buons 2 and 3 are done by pressing
with a narrow object into the circle mark above each (Arrow).
The Actuator movement stops as soon as the push buon is released.
4. "ON" - lights up green when the charger is connected to mains.*
5. "CHARGE" - lights up yellow constantly during charging and will turn o when
charging is completed.
6. Display Pop-up informaon:
Baery power (100 - 50 %) Ok!
Baery power (50 - 25 %) Baery needs charging.
Baery power (Less than 25 %) baery needs charging.
A buzzer will sound when pressing a push buon.
Note! If the buzzer sound starts during an ongoing li complete the li
and charge the li aerwards!
Charge the li immediately! A buzzer will sound when pressing a
push buon. The remaining baery power can only make the li arm go down.
The li is connected to the mains.
Short circuit warning!
check cables and connecons.
Warning is shown unl repaired!
Overload!
Too much load is applied to the li.
Service needed; contact Hill-Rom.
SHORT CIRCUIT
CHECK CONNECTION
!
kg/Ibs.
service
6
4
3
5
2
ON CHARGE
BATTERY
1
Total number of li cycles with load
Work done by actuator; Amp. x Sec.
Number of overload indicaons
Days since last service/Days between services.
xxx
xx/xxx
xxxxxx
xxxxx
A x S
kg/Ibs.
service
6. Informaon display:
Acvate informaon display by a "quick press" at a U P, push buon.
Li-ION baery - specic informaon
Sleep mode! the sleep mode will be acvated in a Li-ION baery if not in use or charged in one week or more. The sleep
mode switches o the baery and it´s electronics to save power. The baery will stay in sleep mode unl the baery is set
back to operaon mode again.
How to set the Li-ION baery back in operaon mode; Charge the baery, when the "CHARGE" indicator,
5
is lit the
baery has been set back in operaon mode and ready for use. Note! We recommend to charge the baery unl charging
is completed, see "Charging the Baery" for more informaon and instrucons.
Delay! a delay to indicators for current baery power at the control box and hand control occurs if the emergency stop
funcon is acvated and restored, see 1 above.

14 www.hillrom.com
7EN140108 Rev. 4 • 2020
Electrical emergency lowering / liing
Use a narrow object to press into the
circle mark above each (Arrow),
See chapter "Operaon" for more
informaon.
Do not use sharp objects, since this
may cause damage on the control box!
ON CHARGE
To acvate the emergency stop:
Push the red Emergency Stop
buon on the control box.
To reset the emergency stop:
Turn the buon clockwise.
ON CHARGE
BATTERY
ON CHARGE
BATTERY
ON CHARGE
BATTERY
Mechanical Emergency Lowering
Emergency lower by moving the
handle up and down. Repeat the
moon unl the paent being lied is
on a rm surface; draw down the sling
bar manually and connue to pump
the handle unl the sling bar is low
enough to enable the sling’s strap
loops to be unhooked.
Adjustment of the li interval level
If it is necessary to reach a lower level with the sling bar,
this can be arranged by lengthening the li strap using the
mechanical emergency lowering device. Do not lengthen the
strap more than necessary as the highest obtainable liing
level is also aected.
An example of when it would be advantageous to lower the li
interval is when liing from the oor using a sling whose strap
loops do not reach up to the sling bar hooks when the li is in
its lowest posion.
Do as follows:
Push down the red emergency lowering handle at the same
me as loading the sling bar (pull down the sling bar with
your other hand). This extends the strap and the sling bar is
lowered. Repeat unl the required strap length is obtained.
Aer mechanical emergency lowering /
Restoring the liing level
If the li strap has been lengthened due to using the emergency
lowing funcon, the li interval height will be lower than
previously. To restore maximum liing height, the li strap must
be reset to its original length.
Do as follows:
1. Remove any load / weight from the strap above the emergency
lowering device. Do this by either placing the sling bar above
the li arm or by another person holding the sling bar up so
that the strap hangs loose.
2. Lower and raise the handle with your le hand. At the same
me tension the strap by turning the knob (a) clockwise with
your right hand. Repeat this procedure unl the red mark on the
strap is just above the emergency lowering device.
a
Lock Unlock
Locking the Wheels
The rear wheels can be locked to prevent rotang and turning. The locking/unlocking of the wheels is done with the foot.
Locked wheels during liing can increase the risk of pping.
NOTE: When liing, the wheels should be unlocked so that the li can be moved to the paent’s center of gravity. The wheels
should be locked, however, if there is a risk of the li rolling into the paent, for instance, when liing from the oor.
Li strap adjustment

15 www.hillrom.com 7EN140108 Rev. 4 • 2020
WRONG!
Figure 1. Figure 2.
Armrest
To use the armrest you need to rotate it from the (vercal)
rest posion up to the (horizontal) support posion. The
armrest have two purposes: to help the paent feel more
secure and facilitate for the caregiver when moving the li.
When using the li to transfer a paent between
rooms, the armrest should be set in the support posion!
rest
posion
support
posion
Parking the sling bar
When the li is not in use or is being moved without
a load, it can be benecial to place the sling bar in the
parking panel.
The parking panel is intended for parking Universal
SlingBars 350, 450 and 600 (all models).
When the sling bar is parked in the parking panel, the
li should not be raised since this could be dangerous and
cause personnel injury or damage to the li if the sling
bar should release and swing out from the panel.
Installaon of Latches
Aer installaon, ensure that the spring
loaded clip is taut against the sling bar and
moves freely in the sling bar hook.
Li correctly!
Before each li, make sure that:
– the Sling loops at opposite sides of the Sling are at the same height
– all the Sling loops are fastened securely in to the Slingbar hooks
– the Slingbar is level during the li, see Figure 1.
If Slingbar is not level (see Figure 2) or if the sling loops is
wrongly
aached to the Slingbar (see Figure 3) lower the user to a rm
surface and adjust according to the Instrucon for use of Sling in
use.
An improper li can be uncomfortable for the user and cause
damage to the li equipment! (see Figure 2 and gure 3).
Figure 3.

16 www.hillrom.com
7EN140108 Rev. 4 • 2020
Transfer from car
Ensure that the li used for car transfers is always stored and charged indoors. Outdoor operaon should be kept to a
minimum. Using the li in harsh condions such as rain, snow or extreme cold may impact the performance of the li
immediately.
Prerequisites
Transfer from car is applicable from the front and rear with the paent in a seated posion. The caregiver must assess that
transfer from the car is achievable. Consideraons should be made regarding the status of the paent (status/condion,
height and weight, posion and accessibility), the relave size of the car and posion of the li equipment. The ground
surface of the transfer area should be level, hard and smooth and free from gravel, debris, ice and potholes. Two caregivers
are recommended for this task. A gurney or a wheel chair should be in the immediate vicinity of the car when performing
the li. Recommended slings for car transfer are the Universal Sling (models 000 & 002) and the High Back Sling (models
200/210/25/26). For correct sling applicaon consult the sling instrucon for use.
Do as follows:
1. Apply the sling according to the sling instrucon for use,
a HandySheet or Tube can be used to reduce fricon. One
caregiver may assist from inside the car if necessary.
2. Posion the li as perpendicular as possible to the car,
with the car door open. Keep the li arm outside the car
and the wheels of the li unlocked.
Posion of the Li when Liing
From/To: Bed Chair/Toilet Seat Floor
NOTE: Place a pillow under the paent’s
head for increased performance and comfort.
Always have the wheels locked when liing
from the oor.

17 www.hillrom.com 7EN140108 Rev. 4 • 2020
3. Aach sling loops to the sling bar. Ensure the correct
applicaon of sling loops to the sling bar. Raise the li to
apply more tension on the sling. Rotate the paent toward
the door opening and guide the legs of the paent out of
the car. Apply fricon reducing devices if necessary.
4a. One caregiver must guide the sling bar and paent
out of the car and ensure that the head of the paent is
guided safely while exing the car. The other caregiver will
need to raise the li while simultaneously pulling the li
backwards.
4b. Noce the correct grip on the sling bar to avoid pinch
injuries to the caregiver as the sling bar is guided out of
the car. Avoid placing hands between the sling bar and the
door frame of the car.
5. Removal of the paent from the car is complete, conn-
ue the transfer to a wheel chair or gurney.

18 www.hillrom.com
7EN140108 Rev. 4 • 2020
Wall mounted charger accessory or table charger housing accessory:
Loosen the holder for the charger cable. Remove the baery pack from the control box by loosening the locking device on top
of the baery pack. See chapter "Assembly".
Charger informaon;
"ON" - lights up green when the charger is connected to mains.
"CHARGE" - lights up yellow constantly during charging and will turn o when charging is completed.
Alt. A. Place the baery pack on the wall mounted charger. Plug the charger cable into mains (100-240 VAC)
check that both "ON" and "CHARGE" on the charger lights up.
Alt. B. Place the baery pack on the charger in the table charger housing. Plug the charger cable into mains (100-240 VAC)
check that both "ON" and "CHARGE" on the charger lights up.
Alt. A Alt. B
Alternave charging procedures
ON
CHARGE
ON
CHARGE
Charging the Baery
Charger informaon
1. "ON" - lights up green when the charger is connected to mains.
2. "CHARGE" - lights up yellow constantly during charging and will
turn o when charging is completed.
Charging with the control box internal charger (standard)
Plug the charger cable into mains (100-240 VAC), see charger informaon
1 - 2 above. The baery is fully charged aer about 6 hours and the
charger disconnects automacally, the yellow "CHARGE" diode turn of.
For maximum baery life, baeries must be charged regularly.
We recommend charging aer each use or every night.
Never charge baeries in a wet area!
NOTE! If the charger cable is stretched out it should be replaced to avoid the risk of the cable geng caught and tear.
NOTE! The li cannot be used when the charger cable is plugged into a wall socket.
NOTE! If the yellow "CHARGE" diode at the control box connuous to be lit aer 8 hours, disconnue charging and replace
the baery with a new one.
NOTE! A damaged baery shall be replaced and contact with leaking uids shall be avoided.
BATTERY
ON CHARGE
1. 2.
ON CHARGE
NOTE! Charging a deep discharged Li-ION baery
When charging a deep discharged Li-ION baery the charger will start charging at a low charging rate to protect the baery.
During the low rate charging no indicator will light up.
When the low rate charging is completed the charger will automacally switch to normal charge rate and the "CHARGE"
indicator will light up yellow and will turn o when charging is completed.

19 www.hillrom.com 7EN140108 Rev. 4 • 2020
Maximum Load
Dierent maximum loads may apply to dierent products on the assembled li unit, sling bar, sling and any other accessories
used. For the assembled li unit, including accessories, the maximum load is always the lowest maximum load rang for any
of the components. A Golvo™ mobile li that is approved for 200 kg (440 lbs) can be equipped with a liing accessory that is
approved for 300 kg (660 lbs). In this case, the maximum load of 200 kg (440 lbs.) applies to the assembled li unit. Study the
markings on the li and liing accessories or contact your Hill-Rom representave if you have any quesons.
Recommended Liing Accessories
Using liing accessories other than those approved can entail a risk.
Generally recommended sling bars and accessories for Golvo mobile lis are described below.
When changing a sling bar or other liing accessories, the highest possible liing height of the li is aected. Before changing
liing accessories you should always ensure that the li, aer change, can full the desired liing height in order to manage
the liing situaons for which the li is to be used.
For addional guidance in selecng a sling, study the Instrucon for use for the respecve sling models. There you will also
nd guidance for combining Liko™ sling bars with Liko slings.
Contact your Hill-Rom representave for advice and informaon on Liko’s product range.
* this product is also available in a version with Quick-Release Hook.
Universal SlingBar 350* Prod. No. 3156074
Max. 300 kg (660 lbs)
Universal SlingBar 450* Prod. No. 3156075
(Standard on Golvo)
Max. 300 kg (660 lbs)
Universal SlingBar 600* Prod. No. 3156076
Max. 300 kg (660 lbs)
Universal TwinBar 670 Twin* Prod. No. 3156077
Max. 300 kg (660 lbs)
Universal SideBars 450 Prod. No. 3156079
including bag
Max. 300 kg (660 lbs)
Sling Cross-bar 450* Prod. No. 3156021
Max. 300 kg (660 lbs)
Sling Cross-bar 670* Prod. No. 3156018
Max. 300 kg (660 lbs)
SlingBar Cover Paddy 30 Prod. No. 3607001
(ts Universal SlingBars 350, 450,
and 600, as well as SlingBar Slim 350)
Bag for SlingBars Prod. No. 2001025

20 www.hillrom.com
7EN140108 Rev. 4 • 2020
Quick-Release Hook
Liko’s Quick-Release Hooks are a system for quick change of liing accessories on
Liko’s mobile and staonary lis. The GolvoTM mobile li must be equipped with
Q-link in order to be used with the Quick-release Hook.
The Quick-Release Hook Universal ts the Universal Bars 350, 450 and 600
(prod. no. 3156074 - 3156076).
Quick-Release Hook TDM ts Sling Cross-bar 450 and 670 (prod. no. 3156021 and
3156018) and Universal TwinBar 670 (prod. no. 3156077).
Contact your Hill-Rom representave for more informaon.
Stretchers
Golvo mobile li can be used for horizontal liing in combinaon with
Liko OctoStretch Prod. No. 3156056
LikoStretch Mod 600 IC Prod. No. 3156065B
FlexoStretch Prod. No. 3156057
Contact your Hill-Rom representave for more informaon.
LikoScale™ device
for weighing a paent in combinaon with Golvo mobile li.
LikoScale™ 350, Max 400 kg (880 lbs) Prod. No. 3156228
LikoScale™ 350 is cered according to the European Direcve
NAWI 2014/31/EU (Non-Automac Weighing Instruments).
LikoScale™ devices only for use in the United states and Canada:
LikoScale™ 200, Max. 200 kg (440 Ibs.) Prod. No. 3156225
LikoScale™ 400, Max. 400 kg (880 Ibs.) Prod. No. 3156226
Contact your Hill-Rom representave for more informaon.
Quick-Release Hook
Universal
Prod. No. 3156508
Quick-Release Hook
TDM
Prod. No. 3156502
X
Y
Z
Q-link
Prod. No. 31590005
LikoScale 350
Prod. No. 3156228
Baery charger,
for wallmounng or to use with
the Table charger housing
Prod. No. 2004106
Table charger housing
excl. charger and baery
Prod. No. 2107103
Baery
Lead baery (Pb)
Prod. No. 2006106
Baery
Li-ION baery
Prod. No. 2006110
Prod. No. 3156056
Leg Protector
Leg Protector (Golvo 9000), grey, pair Prod. No. 2006012G
Holder for Quick Reference Guide Prod. No. 2000100
XS
S
MS
M L
XL XX
L