Liko Sabina II EE Manual

The Sabina sit-to-stand li is especially designed for people
who have diculty in standing up on their own from a
seated posion.
Sabina sit-to-stand li is intended for use with paents
who are able to acvely parcipate in the raising moon.
When standing, they can be moved to a wheelchair or to a
toilet; this gives them standing pracce in connecon with
the transfer.
There are two dierent sling bar opons for Sabina sit-to-
stand li, as well as many dierent sit-to-stand vests.
The paent’s overall mobility determines the choice of
sling bar and sit-to-stand vest.
The Sabina sit-to-stand li equipped with the Comfort
SlingBar combined with the Liko ComfortVest provides an
especially gentle liing acon without pung pressure
under the arms. This combinaon is suitable for those who
are especially sensive to pressure under the arms, such as
people who are paralyzed on one side.
Sabina sit-to-stand li can also, to a limited extent, be used
for passive liing of a paent sing in a sling.
is a warning triangle used for situations which require extra care and attention.
IMPORTANT!
Read the instruction guide for both the patient lift and lifting accessories before use. Lifting and transferring a person always involves
a certain level of risk. It is important to completely understand the contents of the instruction guide. The equipment should be used
by trained personnel only. Please contact Hill-Rom in the event of any uncertainties or questions.
Product Description
In this document, the person being lifted is referred to as the patient, and the person helping is referred to as the caregiver.
SlingBar 350
Comfort SlingBar
Sabina™ II
Sit-to-stand li
Instrucon Guide
Sabina II EE Prod. No. 2020003
7EN155106 Rev. 1
ENGLISH

2
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Safety Instructions ........................................................................................................... 3
Definitions ....................................................................................................................... 4
Technical Data ................................................................................................................. 4
Measurement ................................................................................................................. 5
Assembly ......................................................................................................................6-7
Operation ........................................................................................................................ 8
Charging the Batteries ..................................................................................................... 9
Maximum Load .............................................................................................................. 10
Recommended Lifting Accessories ...........................................................................10-11
Using Sabina sit-to-stand lift to Assist Users into a Standing Position .....................12-14
Using Sabina sit-to-stand lift in Passive Lifting Situations ........................................14-15
Simple Troubleshooting ................................................................................................ 16
Recycling Instructions .................................................................................................... 16
Cleaning and Disinfection .........................................................................................17-19
Inspection and Maintenance ........................................................................................ 20
Table of Contents
NOTE!
This instruction guide contains important information for users of the product. All those who use the product should review
and completely understand the contents of the instruction guide. Remember to keep the instruction guide in a place where it
is always available to those using the product.

3
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Intendeduse: The product is intended for use in following environments: Health care, Intensive care, Emergency ward, Rehabilitation,
Habilitation environment. This product is not intended to be used by the patient alone. Lifting and transferring a patient shall
always be performed with the assistance of at least one caregiver. Contact your Hill-Rom representative for support and advice.
Before using the first time make sure that:
• the lift is assembled in accordance with the assembly instructions
• the lifting accessories are properly attached to the lift
• the batteries have been charged for at least 6 hours
• you have read the instruction guides for the lift and lifting accessories
• personnel using the lift are trained of the correct operation and use of the lift.
Before lifting, always make sure that:
• the lifting accessories are not damaged
• the lifting accessory is selected appropriately in terms of type, size, material and design with regard to the patient’s needs
• the lifting accessory is correctly and safely applied to the patient in order to avoid bodily injury
• the lifting accessory is correctly applied to the sling bar
• the sling bar latches are intact. Missing or damaged latches must always be replaced with new ones;
• the sit-to-stand vest’s/sling’s straps are properly connected to the sling bar hooks when the straps have been fully
extended but before the patient is lifted from the underlying surface.
• as a caregiver assure that the patient not are at risk of falling forward or to any side during lifting.
After use, store the lift in forward direction towards a wall and out of reach of unauthorized!
Never leave a patient unattended in Sabina sit-to-stand lift!
Sabina II EE sit-to-stand lift have been tested by accredited testing institutes, and comply with the requirements for
MDD Class 1 products (MDD 93/42/EEC).
Sabina II EE sit-to-stand lift comply with the requirements of EN ISO 10535:2006, and applicable parts of IEC 60601-1,
IEC 60601-1-2, ANSI/AAMI ES60601-1 and CAN/CSA C22.2 no 60601-1.
Under no circumstances must the lift be modified. Please contact Hill-Rom for more information.
Use of the product adjecent to other equipment should be avoided because it could result in improper operation, if such use
is neccessary, observe and verify that the other equipment is operating normally.
Electromagnetic disturbance, may affect the lifting performance of the product. Modification using other parts than original
spare parts (cables etc.) may affect the electromagnetic compatibility of the product.
Particular care must be taken when using strong sources of potential disturbance, such as diathermy, etc, so that cables are
not positioned on or near the lift. If you have questions, please consult the responsible assistive-device technician or the
supplier.
The lift should not be used in areas where flammable mixtures may occur, for example in areas where flammable goods are
stored.
Safety Instructions

4
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Technical Data
Operang forces
of controls: 2.4 N
Intermient
operaon:
Int. Op 10/90, acve operaon max 2 min.
Only 10% of a given length of me may be
acve, yet no more than 2 min.
Baeries: 2 x 12 V 2.9 Ah. Valve-regulated
lead-acid gel-type baeries.New baeries
are provided by the supplier.
Baery charger: Built-in charger for 100-240 VAC,
50-60 Hz, max 400 mA.
Li motor: 24 V 9,2 A, permanent magnec motor with
mechanical safety mechanism.
Motor base: 24 V, 5 A, permanent magnec motor.
Maximum load: Acve liing: 200 kg (440 lbs)
Passive liing: 150 kg (330 lbs)
Material: Powder-painted steel.
Weight: Total: 41 kg (90 lbs)
Heaviest removable part:
23 kg (50 lbs)
Wheels: Standard front: 75 mm twin wheel.
Standard back: 75 mm individual wheel
ed with brake
Foot rest: Removable.
Lower-leg support: Adjustable in terms of height
and depth. Removable.
Turning diameter: 1180 mm (46.5 inch.)
Emergency
lowering device: Mechanical and electrical.
Liing interval: SlingBar 350: 825 mm (32.5 inch.)
Comfort SlingBar: 785 mm (30.9 inch.)
Liing Speed
(without load):
SlingBar 350: 54 mm/s (2.13 inch./s)
Comfort SlingBar: 47 mm/s (2.1 inch./s)
Maximum
noise output: 46 dB(A)
Protecon class: IP X4
Definitions
1. Li arm
2. Handles
3. Baery
4. Hand control
5. Control box with emergency stop
6. Motor for base-width adjustment
7. Decal: shows risk of crushing against the oor
8. Rear wheels ed with brake
9. Base
10. Front steering wheels
11. Foot rest (removable)
12. Locking handles
13. Wheel for lower leg support adjustment
14. Calf strap (accessory)
15. Lower leg support
The device is intended for use indoors.
Type B, in accordance with the electrical shock
protection class.
Class II equipment.
16. Li motor
17 Mechanical emergency lowering
18. Holder for quick reference guide with
colourcode for sling sizes (accessory)
19. Li mast
20. SlingBar 350
21. Comfort SlingBar
22. Cross bar (only Comfort sling bar)
23. Emergency stop
24. Electrical emergency lowering/raising
25. Indicator lamp, charging (Charge = charging)
26. Indicator lamp, charging (ON = switched on)
27. Liing hook
28. Latches
Forward direction
27
20
21
8
10
6
1
13
11
5
19
22
18
14
12
15
17
16
7
3
13
2
4
9
26 25
24
23
24
28

5
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Measurement
Sabina II
EE
Amin* Amax* B B1 B2 B3 C D D1 D2** E* F F1 Lmax* Lmin* M N O
SlingBar
350 1050 1770 1060 870 590 190 690-1115 530-1005 915 210 900-1000 107 22 1725 800 790 280 310
Comfort
SlingBar 1050 1750 1060 870 555 150 690-1115 530-1005 900 210 900-1000 107 22 1695 810 790 315 340
* Different measurements depending on the height-setting position, please see ”Assembly”, page 6. Note! The measurements are based on the lift
being equipped with standard wheels. When changing wheels, check that the lift still achieves desired lifting height.
** Reference measurement according to Standard EN ISO 10535:2006.
Measurements (mm.)
(inch.)
Sabina II
EE
Amin* Amax* B B1 B2 B3 C D D1 D2** E* F F1 Lmax* Lmin* M N O
SlingBar
350 41.3 69.6 41.7 34.2 23.2 7.5 27.2 - 44.9 20.9 - 39.5 36.0 8.2 35.4 - 39.3 4.2 0.9 67.9 31.5 31.1 11.0 12.2
Comfort
SlingBar 41.3 68.9 41.7 34.2 21.8 5.9 27.2 - 44.9 20.9 - 9.5 35.4 8.2 35.4 - 39.3 4.2 0.9 66.7 31.8 31.1 12.4 13.4
Ref. 1
Ref. 2
700 mm
CDD1
D2**
A max*
A min*
E*
B3**
F
F1
600 mm
Lmax*
B2
B1
B
O
N
M
Lmin*

6
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Assembly
2. With the lift mast, the lifting height may be adjusted to three different
levels. Choose one of the three holes depending on the height of the
patient; the distance between holes is 5 cm/2 inch. (see illustration above).
Secure the lift mast in the base with the included locking handle.
1. Remove the locking handle from
the base. Place the lift mast in the
foot of the base.
3. A) Remove the locking handle from the lift
arm. Slide the sling bar onto the lift arm
with the opening on the lifting hooks
facing upward (see illustration).
B) Attach the locking handle and tighten.
4. Place the battery in the control
box. Make sure that the battery
is secured (a click will be heard).
• Li mast with li arm, control box, li motor
• Sling bar with safety latches and locking handles
• Hand control with cable
• Baery incl. holder for the charging cable
• Base incl. motor for base-width adjustment and locking
handles
• Foot rest and frame for the foot rest
• Lower leg support
• Bag containing instrucon guide, charger connector
cable, and extension cord.
Before assembly, make sure you have the following parts:
NOTE! The sling bar is supplied separately, either as SlingBar 350 or the Comfort SlingBar. We show the Sabina sit-to-stand
lift with Comfort SlingBar in this description.
Individual adjustment of lifting height
Height of patient Position
< 170 cm / 67 inch. 1
160-190 cm / 63-74.8 inch. 2
> 180 cm / 70.9 inch. 3
5. Connect the cables as follows:
- 1. cable, lift motor.
- 2. cable, motor for base-width
adjustment.
- H. cable, hand control.
H
A
B
7. Install the holder for the charging cable:
Hook it on the front edge of the battery
and push down on the back until you hear a
clicking sound.
AC
B
6. A) Connect the charger cable to the socket under the control box.
B) Attach the connector cable to the strain relief system.
C) Plug the charger cable into the connector cable.

7
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
5. Connect the cables as follows:
- 1. cable, lift motor.
- 2. cable, motor for base-width
adjustment.
- H. cable, hand control.
9. Install the lower leg support on the lift mast. Loosen
wheel A in order to adjust the distance to the patient’s
lower legs. Loosen wheel B in order to adjust the
height setting. After adjustment, lock wheels A and B.
8. A) Put the frame for the foot rest over the lift mast’s bracket
to the base. Make sure the frame is securely in place.
B) Push the footrest into the frame.
10. Release the emergency stop
by turning the button in the
direction indicated by the
arrows on the button.
11. If applicable:
Attach the holder for quick
reference guide on the lift mast
according to the assembly
instruction. Place the quick
reference guide in the holder.
• the moon of the li arm corresponds to the buons on
the hand control
• the emergency lowering device works (mechanically and
electrically)
After assembly, make sure that:
• the base-width adjustment works
• the wheel brakes are working
• the indicator lamps on the front of the control box
illuminate during charging.
ON CHARGE
EMERGENCY
BATTERY
AB
S
MS
M L
XL XX
L
12. Before the first use, the lift’s
battery should be charged for
at least 6 hours. For detailed
instructions, see ”Charging the
Batteries”, page 9.
A
B

8
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Hand control
Indicator lamp (A) - charge the battery of the lift!
The lifting motion is operated with the push buttons on the hand
control. The direction in which the arrows are pointing applies
when the hand control is held as shown in the picture. To raise or
lower the lift arm, press or . For lower lifting speed use the
thinner arrows. The lifting motion stops as soon as the push button
is released. For adjustment of the base width, press or .
Operation
Never move the lift by pulling on the
actuator!
ON CHARG
EMERGENCY
BATTERY
ON CHARGE
EMERGENCY
BATTERY
ON CHARGE
EMERGENCY
BATTERY
Emergency stop
Activate:Press the red button on the control box.
Reset:Turn the button in the direction shown by
the arrows until the button springs out.
Locking the wheels
The rear wheels can be locked to prevent rotating and turning. To lock
the wheels, push down the lock pedal with your foot. To unlock the
wheels, push on the raised button at the wheel. During passive/active
lifting, the wheels should be unlocked so that the lift can be moved to
the patient’s centre of gravity.
Electrical emergency lowering/raising
Use a narrow object to push the buttons
inside the labelled holes on the control box.
The object used to press must not be
sharp, since this may cause damage on the
control box!
Mechanical emergency lowering
Pull the red emergency lowering
control straight upwards. Mechanical
emergency lowering only works when
the lift arm is under load, i.e. when a
patient is standing/sitting in the lift.
The lowering motion is slightly delayed.
A
Installaon of latches
Aer installaon, check that the
latch locks and moves freely in the
sling bar hook.

9
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Battery charging and maintenance
To get maximum life time, it is important to charge the battery regularly. We recommend charging after use of the lift or
every night. Batteries are fully charged after approx. 6 hours. When the battery is fully charged, the charger is switched off
automatically. If the lift is not used every day, we recommend connecting the lift to the charger, or pushing in the emergency
stop after use, in order to turn off the current and save the battery. Ensure that the battery is fully charged before pushing
the emergency stop.
NOTE! The li cannot be charged with the emergency stop engaged.
NOTE! When charging, a yellow indicator lamp on the control box will illuminate. The yellow lamp turns off when the battery
is fully charged. If the lamp has not turned off after 8 hours of charging, the battery probably needs to be replaced. Stop
charging and replace the battery.
Never charge batteries in a wet area.
Charging the Batteries
Charging
Alt. A Alt. B
Built-in charger (standard.):
Connect the charger cable to a socket
(100-240 V AC). Make sure that both
indicator lamps on the charger are
illuminated. The yellow lamp indicates
that charging is taking place, while a
green lamp indicates that power is being
supplied to the charger. If the charger
cable is beginning to stretch, it should be
replaced in order to minimize the risk of
the cable getting stuck and breaking.
Wall-mounted charger or table charger:
Detach the holder for the charger cable. Remove the battery from
the control box by releasing the blocking bolt on top of the battery.
Alt. A. Place the battery on the wall-mounted charger. Plug the charger
into a socket (100-240 V AC). Make sure that both indicator lamps on the
charger are illuminated. The yellow lamp indicates that charging is taking
place, while a green lamp indicates that power is being supplied to the
charger.
Alt. B. Place the battery on the charger in the table charger housing. Plug
the charger into a socket (100-240 V AC). Make sure that both indicator
lamps on the charger are illuminated. The yellow lamp indicates that
charging is taking place, while a green lamp indicates
that power is being supplied to the charger.
NOTE! The lift cannot be used when the charger cable is plugged into a socket.
Indications for charging the battery
In the event of low battery voltage, a signal from the control box will sound. At the same time, an indicator on the hand
control will illuminate. When this happens, the battery must be charged as soon as possible. However, there is sufficient
power for a few more lifts. There is a display on the control box indicating current battery capacity. When all fields are black,
the battery is fully charged. When the symbol ( ) is displayed, the battery must be re-charged as soon as possible.
ON CHARGE
EMERGENCY
Sabina II EE sit-to-stand li comply with the Direcve 2002/96/EC on waste electrical and electronic equipment.
Old baeries are to be deposited at the nearest recycling facility in accordance with local regulaons or given to
personnel authorized by Hill-Rom.

10
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Recommended Lifting Accessories
Holder for Quick Reference Guide Prod. No. 2000100
Quick Reference Guide Sabina II
Swedish/Finnish Prod. No. 2020100SVFI
Norwegian/Danish Prod. No. 2020100NODK
English/Spanish Prod. No. 2020100ENES
German/French Prod. No. 2020100DEFR
French/Dutch Prod. No. 2020100FRNL
Italian/Portuguese Prod. No. 2020100ITPT
Calf Strap Prod. No.20290022
Calf strap may be used for those patients who need securing of a weak leg
or need a prompt not to step off of the foot rest.
Leg Protector Prod. No. 20190029
Heel Support Sabina
Heel supports are used if the patient’s feet need to be fixed to the foot rest.
Foot straps are included.
Be aware of any decreased mobility and/or the risk of hyperextension
of the knee joints when using Sabina Heel Support.
Different maximum loads may apply to different products on the assembled lift unit: lift, sling bar, sit-to-stand vest and
any other accessories used. For the assembled lift unit, including accessories, the maximum load is always the lowest
maximum load rating for any of the components. Check the markings on the lift and lifting accessories, contact your Hill-Rom
representative if you have any questions.
Maximum Load
Using other liing accessories than those recommended below may induce risk.
Below is a description of recommended lifting accessories for Sabina II. Study also the instruction guide for respective sit-to-
stand vest/sling or lifting accessory for further guidance.
Contact your Hill-Rom representative for advice and information on Liko’s product range.
XS
S
MS
M L
XL XX
L
VIKTIGT!
Dennaanvändaranvisning ersätter inte lyftens
bruksanvisning, vilken kan laddas ner från
www.liko.se.
Säkerhetsföreskrifter
Sabina II
Användaranvisning
Svensk
• Läs bruksanvisning för både patientlyft och
lyfttillbehör före användning.
• Planera lyftmomentet noggrant.
• Innan brukaren lyfts från underlaget, men när
lyftbanden är ordentligt sträckta, är det viktigt
att kontrollera att bandöglorna är rätt påhakade
på lyftbygeln.
• Maxlast: 200 kg.
För bibehållen maxlast krävs tillbehör avsedda
för samma belastning eller mer.
4
3
1
8
9
67
2
5

11
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
SeatStrap SlingBar
Prod. No. 2027007: can be used with Sabina II sit-to-stand lift.
Prod. No. 2027006: can be used with earlier Sabina sit-to-stand lift
models, but can also be used with Sabina II sit-to-stand lift.
Sabina SeatStrap Prod. No. 3591115
The SeatStrap is an accessory that facilitates the first part of the raising motion.
The SeatStrap is connected to a SeatStrap SlingBar, which helps the patient
move the seat up when raising. In standing position, the SeatStrap can be easily
disconnected so that it is not in the way when, e.g., going to the toilet.
Battery charger, wall-mounted Prod. No. 2004106
or for use with a table charger housing
Extra battery Prod. No. 2006106
Table charger housing Prod. No. 2107103
excl. charger and battery
Prod. No. 2027006
Prod. No. 2027007

12
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
There are two different sling bar options available for Sabina sit-to-stand lift, as well as many different sit-to-stand vests.
The patient’s overall mobility determines which sling bar and sit-to-stand vest to use. Carefully read the instruction guide
for the lifting accessories used. Before using Sabina sit-to-stand lift, it is important to make an individual setting of the lifting
height, see page 6.
Using Sabina sit-to-stand lift to Assist Users into a Standing Position
Raising a person with active lifting using Sabina sit-to-stand lift with SlingBar 350
1. Place the SupportVest around the patient according to the
vest’s instruction guide. Place Sabina sit-to-stand lift in front of
the patient and adjust the width of the base. Place the feet in
the middle of the foot rest with the lower legs parallel to the
lower leg support. Adjust the height and depth of the lower leg
support as needed for comfortable support below the kneecap.
2. Connect the vest’s straps to the sling bar’s hooks.
If applicable: tighten the calf strap.
3. Raise the sling bar about 10–20 cm (4-8 in). The patient
grabs the sling bar. Continue the lifting procedure. If the
patient leans backwards, the raising will be made easier,
preventing the vest from sliding up. The height to which
the lift should proceed varies from person to person.
Before the patient is lifted from the underlying
surface, but after the straps have been fully extended,
make sure the straps are properly connected to the sling
bar.
4. For a more upright position, continue the lifting
motion to the uppermost position. The raising motion
can be experienced as unpleasant for the person not
used to it. Remember that Sabina II EE sit-to-stand
lift has two different speeds. For maximum comfort,
the lift mast should be affixed to the base in the best
possible of the three fastening holes. See page 6.
For this sling bar, we recommend Liko SupportVest mod. 91 or Liko SafetyVest mod. 93, 94. When using SlingBar 350, the
patient has the arms outside the sling. SlingBar 350 in combination with SafetyVest mod. 93, 94 gives the patient extra support
in the standing-up situation. Below please find a description of the use of the SupportVest mod. 91. See the instruction guide
for the respective sit-to-stand vest for more information.

13
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Raising a person with active lifting using Sabina sit-to-stand lift with the Comfort SlingBar
1. Place the ComfortVest around the patient according to
the vest’s instruction guide. Place Sabina sit-to-stand
lift in front of the patient. Adjust the width of the base.
Place the feet in the middle of the foot rest with the
lower legs parallel to the lower-leg support. Adjust the
height and depth of the lower-leg support as needed for
comfortable support below the kneecap.
2. Connect the vest’s straps to the sling bar’s hooks.
If applicable: tighten the calf strap.
3. Raise the sling bar about 10–20 cm (4-8 in).
The patient grabs the sling bar. Continue the lifting
procedure. If the patient leans backwards, the raising
will be made easier, preventing the vest from sliding up.
The height to which the lift should proceed varies from
person to person.
Before the patient is lifted from the underlying
surface, but after the straps have been fully extended,
make sure the straps are properly connected to the
sling bar.
4. For a more upright position, continue the lifting motion
to the uppermost position. The raising motion can be
experienced as unpleasant for the person not used to
it. Remember that Sabina II EE sit-to-stand lift has two
different speeds. For maximum comfort, the lift mast
should be affixed to the base in the best possible of the
three fastening holes. See page 6.
For this sling bar, we recommend Liko ComfortVest mod. 95. This combination is suitable for people who are especially
sensitive to pressure under the arms, such as people who are paralyzed on one side. The ComfortVest is designed to lift
behind the back and on the outside of the arms. The Comfort SlingBar can also, to a limited extent, be used with Liko
SafetyVest mod. 93 and 94, especially for larger patients. Below is a description of how to use ComfortVest mod. 95. See the
instruction guide for the respective sit-to-stand vest for more information.

14
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Problems while helping a patient get to his feet
The patient does not reach a sufficiently upright position - what is to be done?
Sometimes this is due to the patient’s state of health or mobility: weakened musculature, lack of strength and/or diminished
mobility in hip or knee joints. In order to get the best possible use out of Sabina sit-to-stand lift, there are some things to keep
in mind:
1 Connect the vest's inner strap loop (B) to the sling bar hooks.
2 Raise the lift mast to achieve higher lifting height. See adjustment of lifting height, page 6.
3 Try a smaller vest size. A smaller vest means a shorter distance to the hooks and a more upright standing position.
The patient has a hard time participating in the first part of the raising motion - what is to be done?
Sabina SeatStrap is an accessory meant for patients who need extra help with raising the seat during the first part of the
raising motion. For more information, see “Recommended Lifting Accessories,” page 10-11, or read the instruction guide for
Sabina SeatStrap.
Using Sabina sit-to-stand lift in Passive Lifting Situations
For passive lifting, we recommend a sling model that does not restrict the lifting height too much. Adjustment on a
case-by-case basis is always important to functionality and security. The patient’s overall mobility determines the choice of
sling model and sling bar. Remember that the maximum load for passive lifting is reduced from 200 kg (440 lbs) to 150 kg
(330 lbs); this is due to the fact that during passive lifting, the foot rest does not bear any of the load.
Sabina sit-to-stand lift with SlingBar 350 (bar width 350 mm)
For this sling bar, we recommend Liko OriginalSling mod. 10 and 11, Liko HygieneSling mod. 40, 41, 45 and 46,
as well as the Liko Straps.
Sabina sit-to-stand lift with Comfort SlingBar (bar width 600 mm)
For this sling bar, we recommend Liko UniversalSling mod. 000 and 002, as well as Liko OriginalSling mod. 10 and 11. See the
respective instruction guide for the sling model for more information or contact Hill-Rom for further guidance.
1. Disassemble the lower leg support: Unscrew screw A.
Pull out the lower leg support. Remove the foot rest: Grab
the front edge of the frame. Fold it up and lift it off the
base.
2. Apply suitable sling according to the sling’s instruction
guide. Above Liko HygieneSling mod. 40 is applied.
Passive lifting using Sabina sit-to-stand lift with SlingBar 350

15
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
3. Advance the lift. Connect the sling’s suspension loops to
the sling bar’s hooks. The height setting of the lift mast
may have to be adjusted, see page 6.
Before the patient is lifted from the underlying
surface, but after the sling’s straps have been fully
extended, make sure the straps are properly connected
to the sling bar.
4. Raise the sling bar to the lowest height necessary to
perform the transfer.
Make sure that the lifting motion is not so high that
the patient gets too close to the lift mast!
NOTE!
Lifting seated persons with Sabina sit-to-stand lift cannot replace lifting procedures for sitting persons using traditional
mobile lifts, e.g. using Viking™ mobile lift, Uno™ mobile lift, Golvo™ mobile lift, or LikoLight™ mobile lift. The function
is intended as a temporary solution when the patient cannot manage an active raising motion using Sabina sit-to-stand
lift. If the need for passive lifting persists, we recommend that you switch to one of the lifts mentioned above.

16
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
1. Check that the emergency stop has not been engaged.
2. Make sure that the cables to the control box are connected
correctly.
3. Make sure that the charging cable is not connected to a
socket.
4. Check the battery voltage.
5. Check that the battery’s contact plates are not defective or
broken.
6. If the lift still does not work properly, please contact Hill-Rom.
1. Check that the emergency stop has not been engaged.
2. Check that the battery’s contact plates are not defective or
broken.
3. If the lift still does not work properly, please contact Hill-Rom.
1. Check that the emergency stop has not been engaged.
2. Use the selected electrical emergency lowering device to lower
the patient onto a firm surface.
3. Use the selected mechanical emergency lowering device to
lower the patient onto a firm surface.
4. Check the battery voltage.
5. If the problem remains, please contact Hill-Rom.
Contact Hill-Rom.
Simple Troubleshooting
The lift does not go up/down.
Base width adjustment does not
work (in/out).
The charger doesn’t work.
The lift is stuck in a high position.
If you hear unusual sounds.
Waste of Electrical and Electronic
Equipment (WEEE).
Metals
Lead baery (Pb)
Recycling Instrucons

17
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Safety Recommendaons
Cleaning and disinfecng procedures for Liko™ Mobile lis. This instrucons do not replace the facility’s own cleaning and
disinfecon policies.
• Wear protecve equipment according to manufacturer’s instrucon and per facility protocol throughout the cleaning
operaons, such as: rubber gloves, goggles, apron, face mask and shoe covers.
• Unplug mains (AC power source) before cleaning and disinfecon.
• Never clean the li by pouring water on it, steam cleaning it, or by using a high-pressure jet.
• Refer to the recommendaons made by the cleaning and disinfecng product manufacturer.
Equipment
• Protecve equipment (such as: rubber gloves, goggles, apron, face mask and shoe covers) as recommended by the
facility protocol and manufacturers instrucons
• Clean buckets
• Cloths for washing and drying
• So brush
• Warm water
• To nd Cleaning / Disifectants compable or not compable for use on Liko’s products, follow the
”Applicaon of commonly used Cleaning / Disinfectants on Liko products” in this document.
Cleaning Instrucons
1. Unplug mains (AC power source) before cleaning and disinfecon.
2. Clean the li with a cloth moistened with warm water and a neutral cleaning agent approved by your organizaon.
A so brush may be used to remove stains and resistant dirt.
3. Wipe o the enre li with a cloth moistened with clean water starng from the top and working down. The cloth shall
not be so damp that it drips. To have access to all areas run the li into the highest and lowest posions and extend the
base width adjustment enrely in and out. Remove the Baery to have access behind the baery. The calf strap may be
machine washed 60-80°C (140-176°F), see ”Care and Maintenance of Liko Slings” for more informaon.
NOTE! Do not clean the piston rod!
4. Pay special aenon to the following areas:
• Sling bar (dierent designs)
• Handles
• Mechanical emergency lowering (dierent designs)
• Hand control
• Emergency stop
• Lower-leg support
• Foot rest
• Locking handles
• Wheels
Do not clean
the piston rod!
Cleaning and Disinfecon

18
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Disinfecon Instrucons
1. For the use of suitable disinfectants see ”Applicaon of commonly used Cleaning / Disifectants on Liko products” in this
document.
2. Use the choice of disinfectant according to the manufacturer’s instrucons and repeat the work step as in”Cleaning
Instrucons"
3. Remove traces of disinfectant aer disinfecon. Wipe o the li with a cloth moistened with clean water starng from
the top and working down. The cloth shall not be so damp that it drips.
The li may not be cleaned with CSI or equivalent.
The hand control may not be cleaned with Viraguard or equivalent.
The control box may not be cleaned with Anioxy Spray or equivalent.
The foot rest may not be cleaned with Terralin Protect, Virex II or equivalent.
The leg support on Sabina II, S/N up to 460899 may only be cleaned with warm water and a facility approved
neutral detergent.
The leg support on Sabina II S/N from 460900 may be cleaned with the recommended disinfectants.

19
Sabina™ II sit-to-stand li • 7EN155106 Rev 1 www.hill-rom.com I www.liko.com
Applicaon of commonly used Cleaning / Disinfectants on Liko products
Chemical class Acve ingredient pH Cleaners /
Disinfectant *) Manufacturer *) May not be used on the
following items:
Quaternary ammonium chloride Didecyl dimethyl ammonium chloride = 8.704%
Alkyl dimethyl benzyl ammonium chloride = 8.19%
9.0 – 10.0 in use Virex II (256) Johnson/Diversey Foot rest for Sabina™ and
Roll-On™
Quaternary ammonium chloride Alkyl dimethyl benzyl ammonium chloride = 13.238%
Alkyl dimethyl ethylbenzyl ammonium chloride = 13.238%
9.5 in use HB Quat 25L 3M
Accelerated Hydrogen Peroxide Hydrogen Peroxide 0.1 -1.5%
BenzylAlcohol: 1-5% Hydrogen Peroxide 0.1 -1.5% BenzylAlcohol: 1-5%
3 Oxivir Tb Johnson/Diversey The li straps for Golvo™
and ceiling lis
Phenolic Ortho-Phenylphenol = 3.40%
Ortho-Benzyl-para-Chlorophenol = 3.03
3.1 +/- 0.4 in use Wexcide Wexford Labs
Bleach Sodium hypochlorite 12.2 Dispatch Caltech The li straps for Golvo™
and ceiling lis
Alcohol Isopropyl alcohol = 70% 5.0 – 7.0 Viraguard Veridien Hand controls for all lis Quaternary ammonium n-Alkyl dimethyl benzyl ammonium chlorides = 0.105%
n-Alkyl dimethyl ethylbenzyl ammonium chlorides = 0.105%
11.5 - 12.5 CSI Central Soluons Inc. Viking™, Liko M220™, Liko
M230™, Uno™, Sabina™, Golvo™, LikoLight™, Roll-On™, Likorall™, Mulrall™
Benzyl-C12-18-alkyldimethylammonium, chlorides
Benzyl-C12-18-alkyldimethylammonium, chlorides (22 %) 2-Phenoxyethanol (20 %) Tridecylpolyethylenglycolether (15 %) Propan-2-ol (8 %)
approx 8.6 in use Terralin Protect Shülke Foot rest for Sabina™ and
Roll-On™
Organic peroxide (type E, solid) Magnesium monoperoxyphtalate hexahydrate (50-100%)
Anionic surfactant (5-10%) Nonionic surfactant (1-5%)
5.3 in use Dismozon Pur Bode The li straps for Golvo™
and ceiling lis
Ethanol Hydrogen peroxyde (2.5-10 %)
Lauryldimethylamine oxid (0-2.5 %) Ethanol (2.5-10 %)
7Anioxy-Spray WS Anios Control box for all mobile
lis
Troclosene sodium Adipic acid 10-30%
Amorphous silica < 1% Sodium Toluene sulphonate 5-10 % Troclosene sodium 10-30 %
4-6 in use Chlor-Clean Guest Medical Ltd The li straps for Golvo™
and ceiling lis
*) Or equivalent

© Copyright R&D Liko AB 2018
Liko AB
Nedre vägen 100
SE-975 92 Luleå, Sweden
[phone]
www.hill-rom.com I www.liko.com
Care and Maintenance
For trouble-free use, certain details should be checked each day the lift is used:
• Inspect the lift and check to make sure that there is no external damage.
• Check the functionality of the locking handles.
• Check the functionality of the latches.
• Check the raising, lowering and the base-width adjustment.
• Check to make sure that the emergency lowering (both electrical and mechanical) works.
• Charge the batteries each day the lift is used and make sure the charger works.
When necessary, clean the li with a moist cloth and check that the wheels are free from dirt. Find more detailed informaon
regarding cleaning and disinfecon of your Liko product in chapter; Cleaning and Disinfecon.
The lift should not be exposed to running water.
Service
Sabina sit-to-stand lift should be periodically inspected at least once a year. Service are not allowed with patient in lift.
Periodic inspection, repair and maintenance should be performed only in accordance with the Liko Service Manual and
by personnel authorized by Hill-Rom and using original Liko spare parts.
Service Agreement
Hill-Rom offers the opportunity to enter into service contracts for the maintenance and regular inspection of your Liko product.
Expected Life Time
The product has an expected life time of 10 years when correctly handled, serviced and periodically inspected in accordance
with Liko’s instructions.
Transport and Storage
During transportation, or when the lift is not to be used for a long time, the emergency stops should be engaged.
The environment where the lift is transported and stored should have a temperature of 10–40 °C (50–104 °F) and a relative
humidity of 30 to 75 %. The air pressure should be 700–1060 hPa.
Product Changes
Liko’s products undergo continuous development, which is why we reserve the right to make product changes without prior
notice. Contact your Hill-Rom representative for advice and information about product upgrades.
Design and Quality by Liko in Sweden
Liko is quality certified in accordance with ISO 9001 and its equivalent for the medical device industry, ISO 13485.
Liko is also certified in accordance with environmental standard ISO 14001.
Inspection and Maintenance