Lockly LUX COMPACT PGD688FSN User manual

MORTISE EDITION
LUX COMPACT
INSTALLATION
MANUAL
ERP机型： PL3568FNQ-GL-SMT00011A-V1
Designed：曹显贵 Date：2020-07-28
描述:安装指引:PL3568FNQ/PGD688FN，SMT000,REV.D（IMPGD68820200728）,196x196mm,
128g双粉纸, 双面印4C+2专色，过哑油，装订本14页28面（其中有一张折叠页），
RoHS2.0,REACH,Prop65，POPs，PAHs
ERP P/N：
REV：0.5
KYMC
2915C
KYMC
2915C 2915C7540C

INSTALLATIONOVERVIEW & PARTS LIST
R
V
2x
P
G
M1
M2
O
D
Spare parts
package
A
C
B
U
D
S
LK
N
Q
F
H
I
P
3x
O
2x
Exterior
T
G
4x
M
PM5 x 25MM Screw, Door thickness 1-19/50"~1-69/100"(35~43mm)
PM5 x 35MM Screw, Door thickness1-69/100"~1-97/100"(43~50mm)
M 1
M 2
*NOTE: You can either use the exterior adhesive (T) or slotted barrel extension (U) to stabilize the
exterior part. Slotted barrel extension (U) requires drilling an extra hole. Use provided Template
for drilling instructions if needed.
This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing
door installation.
If you wish to change the orientation of the lock for a Left Swing door, go to Step 4 for instructions.
Locking Pin
Spindle
Slotted Barrel
Extension
Exterior Assembly
Keys
Exterior Adhesive
Clamping Tool
For changing
handle orientation
Positioning Rod
For installing mounting
plate (LK)
Battery Cover
BM4 × 8MM Screw
Interior Assembly
PM5 Screw Mounting Plate
Interior Adhesive
BM4 x 32MM Screw
Strike Plate
Dust Box
KA4 x 20MM Screw
Latch

GETTING STARTED - YOUWILL NEED
All the parts you need to install the Lockly®Lux Compact is included in your package.
However, we do need a few tools.
Phillips Screwdriver
Flathead Screwdriver
Ruler
Pliers
Required Tools Optional
Screwdriver with drill bits
Drilling is not required to install the lock, and is optional. However if you are installing
your lock on a brand new door, a drill is required if there are no holes prepared
for lock installation.

There are 4 common door-opening directions, the lockset ships default for is
for RIGHT IN-SWING Doors. You may skip this step if you are sure your door is
a Right In-Swing Door. Otherwise, see the illustrations below to confirm your
door opening direction and change your latch throw orientation if needed.
STEP 1: ADJUSTING LOCKSET TO YOUR DOOR ORIENTATION
LEFT IN-SWING DOOR
LEFT OUT-SWING DOOR Make sure the latch
throw is correctly oriented
as shown to fit your left
out-swing door.
Make sure the latch
throw is correctly
oriented as shown to fit
your left in-swing door.

RIGHT OUT-SWING DOOR Make sure the latch
throw is correctly oriented
as shown to fit your right
out-swing door.
RIGHT IN-SWING DOOR Make sure the latch
throw is correctly oriented
as shown to fit your right
in-swing door.

1、Move the metal barrier upwards.
3、Hold the moving lip aligned to
latch and twist downwards to 180°.
4、Release the metal barrier
to fully extend the latch.
2、Push the latch throw inwards
and position the moving lip
aligned with the latch inside
the case.
HOW TO ADJUST THE LATCH THROW
The Factory setting or the throw is for right in-swing door. You do not need
to change direction if you have a right in-swing door. Here is here is how to
change the latch throw direction.

Interior Panel
for Part N
STEP 2: PREPARING THE DOOR
Use provided drilling templates to prepare door for installation.
You would need professional door drilling tools.
2-3/8"(60mm)
Exterior Panel
for Part B
1/2"
12mm
4-7/50"
105mm
2-1/8"
54mm

3. INSTALLING THE LOCKSET (PART F)
3.1 When installing the lockset, ensure the latch is at the top position
and deadbolt is at the bottom.
3.2 Use provide screws (G) to secure the lockset position.
G
G
F

STEP 4: CHANGING HANDLE ORIENTATION FOR RIGHT OR
LEFT SWING DOORS
The lock ships default for Right Swing Doors. You may skip STEP 4 if your
door is a Right Swing Door. To change your door handle orientation for a left
swing door,please continue reading.
Changing the Exterior Handle Orientation
Insert the key and rotate to align the
two white dots as shown in the picture.
IMPORTANT:
The following steps are only possible
when these two white dots are aligned!
4.1

R
4.2
4.3
Use the provided Clamping tool (R) to
push in the two metal pins at the base
of the lock handle, located at the 3
o’clock and 9 o’clock positions, and
remove the handle once the pins are
compressed.
Rotate the handle 180 degrees to the
other side of the lock.
Using your fingers, press the two pins
located on the left and right side of
the the lock to insert the handle back
onto the lock.

4.4
Confirm that your installation was
complete by checking if the pins are
flush against the handle, and has
popped out. Adjust the handle
accordingly to make sure the pins are
fully decompressed and sits flush
gainst the surface.
4.5
Check that yor handle works smoothly
by giving it a turn up and down.
4.6
Twist key back to horizontal position.
The key can be taken out once it goes
back to the horizontal position.

4.7
4.8
4.9
Remove the screw position on point "R"
Use a flathead screwdriver to press the
middle marker and move to point "L".
Insert the removed screw from point "R"
screw tightly to point "L".

Remove the screw by turning
counter clockwise. Then rotate the
handle 180° in the direction of the
arrow until the screw hole aligns
with marker as shown.
Securely screw clockwise as shown
to complete your handle orienta-
tion change.
4.10
4.11
Changing the Interior Handle Orientation

STEP 5: INSTALLING PART C
5.1 5.3
5.4 Peel paper layer OFF the Adhesive
tape and prepare for installation.
5.2
Install Spindle (C) with the holes
side into the base of the lock
and align the holes locate in
the 3 o’clock and 9 o’clock
position.
Insert locking pin (D) in to
the hole as shown above.
Carefully bend the end of the locking
pin (D) with a needle nose pliers.
Failure to bend the locking pin and turn
the handle freely without obstruction will
result to malfunction.
D

Install the exterior lock as shown to
the left by aligning the lock straight
and passing the cable and attached
rods through the lockset.
Align the lock straight and press hard
(if you use the 3M tape in step 5.4) to
secure the top of the lock.
STEP 6: INSTALLATING THE LOCK (EXTERIOR)
Exterior
6.2 6.3
6.1
Pass the Spindle (C) through
the center of the lockset, and
the round rods through the sides
in their respective holes. The cable
should run undeneath the lockset.

Install the side with the black
plastic seal against the door
Positioning rods slide through these holes.
7.1
7.2
STEP 7: INSTALLING THE LOCK (INTERIOR)
Interior
V
Insert Positioning Rods (V) into
the the holes to the left and
right of the Spindle (C).
The holes are located at the 3
o’clock and 9 o’clock positions.
Interior Mounting Plate (LK) will go
against the interior side of your door.
Remove the paper layer off of the
Adhesive Tape and align the
positioning rods on the bottom of
the plate to the corresponding left
and right holes.
Mounting Plate (LK)

O
2x
LK
PM5X25mm
PM5X35mm
M1
M2
7.3
7.4
Screw (O)
*Secure top with M1 or M2
* If you have drilled a hole on the
top in Step 1, please secure the
hole with screw M1 or M2 depending
on your door thickness. Skip this if
no hole was drilled in Step 1.
Pull the cable from the exterior
lock through the rectangular
hole underneath the positioning
rods and spindle.
Remove the position rods (V)
and replace them with screws (O)
Tighten clockwise until the mounting
plate is secure.

7.5
7.6
Plug the cable that is coming through
the door into the lock interior. Make sure
you match the direction of the plug
correctly and matching the red side of
the plug with the red side on the lock.
Secure the connection by ensuring the
snap is inserted tightly.
In case you need to reinstall the lock and
disconnect the cable, make sure to press
the snap to release the plug before carefully
pulling it out. Do not force to pull the plug as
this may result to lose connection and
damage the lock.
Align the square rod to the lock interior
and attach the Interior lock to the Interior
mounting plate.
While you are doing so, gently push
some of the excess cable through the
rectangular hole into the door.
Place the remaining cable against the
interior side of the lock interior so the
lock interior sits securely onto the
mounting plate.