Lockly LATCH EDITION SECURE PGD628 User manual

INSTALLATION
MANUAL
SECURE
LATCH EDITION

INSTALLATIONOVERVIEW & PARTS LIST
Exterior
T
O
3x
G
4x
P
3x
D
S
L K
N
Q
F
H
M
C
B
U
A
Adhesive
PM5 x 25MM Screw, Door thickness 1-19/50"~1-69/100"(35~43mm)
Battery Cover
BM4 × 8MM Screw
Interior Assembly
Mounting Plate
Interior Adhesive
Strike Plate
KA4 x 20MM Screw
Locking Pin
Spindle
Slotted Barrel
Extension
Exterior Adhesive
Exterior Assembly
F1 Latchbolt F2 Latchbolt
Keys
Latch
PM5 Screw
BM4 x 32MM Screw
PM5 x 35MM Screw, Door thickness1-69/100"~1-97/100"(43~50mm)
M 1
M 2
*NOTE: You can either use the exterior adhesive (T) or slotted barrel extension (U) to stabilize the
exterior part. Slotted barrel extension (U) requires drilling an extra hole. Use provided Template
for drilling instructions if needed.
2-3/4"
(70mm)
2-3/8"
(60mm)
Measure distance between the center of the hole tothe edge of door:
Use F1 if 2-3/8"(60mm) or F2 if 2-3/4"(70mm)
R
Clamping Tool
For changing
handle orientation
W
2x
Positioning Rod
For installing mounting
plate (LK)
Activation Card
This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation.
If you wish to change the orientation of the lock for a Left Swing door, go to Step 3 for instructions.
LOCKLY.COM | HOTLINE: [phone] | EMAIL: [email protected]OM
AUTHENTIC LOCKLY PRODUCT | DESIGNED IN USA | CARD IS PRINTED WITH A SPECIFIC PATTERN
SECURE ADDITIONAL DOORS AT A DISCOUNT:HTTP://WWW.LOCKLY.COM/MORE
ACC20200402
LOCK SERIAL
ACTIVATION CO DE
PGDxxxxxxxxxx
xxxxxxxx SCAN & SAVE

GETTING STARTED - YOUWILL NEED
All the parts you need to install the Lockly®Secure Latch Edition is included in your package.
You will require the following tools with some optional items for ease of installation.
Phillips Screwdriver
Flathead Screwdriver
Ruler
Pliers
Required Tools Optional
Screwdriver with drill bits
Drilling is not required to install the lock, and is optional. However if you are installing
your lock on a brand new door, a drill is required if there are no holes prepared for
lock installation.

STEP 1: PREPARING THE DOOR
1.1
If you are installing the Lockly®Secure
smart lock on an existing door, please
remove existing door hardware and latch
or bolts before installing the new lock.
You can remove most existing door locks
with a screwdriver.
If you are having problems removing
your existing door lock or unsure if what
you are doing can damage the existing
door, please contact a locksmith or the
current door hardware manufacturer for
assistance.
1.2
After removing the existing lock, make sure your door is properly prepared. If you
need to drill holes in your door, please use supplied templates to assist.

1 " - 2"
(35mm - 50mm)
2 "
54mm
1"
25mm
Backset
2" (60mm)
or 2 " (70mm)
IMPORTANT NOTICE
*
Measure and confirm your door is
between
1 " - 2" ( 35mm - 50mm).
Measure and confirm the hole in the
door is
2 " (54mm).
Measure and confirm that the backset
is between
2 " (60mm) to
2 " (70mm).
Measure and confirm that hole in the
door edge is 1” (25mm).
1.3
1.4
1.5
1.6
* You are not required to drill an extra hole on your door. We have provided double
sided Adhesive tape for you to help stabilize the lock during installation. Only drill a hole
if you wish to have added stability. Please refer to the provided template for drilling if
needed.

STEP 2: INSTALLING THE LOCKSET
2.1 Measure the distance between center of front door hole to the edge of your door
and select the correct lockset. Select F1 if 2-3/8"(60mm) or F2 if 2-3/4"(70mm).
2-3/4"
(70mm)
2-3/8"
(60mm)
F 1 F 2
G
G
G
G
2.2 Install the lockset with the slanted side of the latch facing towards the closing direction.
Slanted side Facing Door Frame when closing Slanted side Facing Door Frame when closing
OR
Example 1 Example 2
2.3 Secure lockset with provided screws, labelled G (Step 2.1) as shown.

STEP 3: CHANGING HANDLE ORIENTATION FOR
RIGHT OR LEFT SWING DOORS
The lock ships default for Right Swing Doors. You may skip STEP 3 if your door is a
Right Swing Door. To change your door handle orientation for a left swing door,
please continue reading.
How to determine if your door is a Right Swing or Left Swing door?
While facing the door, if the door hinges are on the right side of the door, you have a Right Swing
Door. If the hinges are on the left side of the door, you have Left Swing Door.
Changing the Exterior Handle Orientation
Insert the key and rotate to align the
two white dots as shown in the picture.
IMPORTANT:
The following steps are only possible
when these two white dots are aligned!
3.1

R
Use the provided Clamping tool
(R) to push in the two metal pins
at the base of the lock handle,
located at the 3 o’clock and 9
o’clock positions, and remove the
handle once the pins are
compressed.
3.2
Rotate the handle 180 degrees to
the other side of the lock.
Using your fingers, press the two
pins located on the left and right
side of the the lock to insert the
handle back onto the lock.
3.3

Confirm that your installation was
complete by checking if the pins
are flush against the handle, and
has popped out. Adjust the handle
accordingly to make sure the pins
are fully decompressed and sits
flush against the surface.
3.4
Check that your handle works
smoothly by giving it a turn
up and down.
3.5
3.6
Twist key back to horizontal position.
The key can be taken out once it goes
back to the horizontal position.

Remove the screw by turning counter
clockwise and rotate the handle 180° in
the direction of the arrow as shown.
Make sure the screw hole is aligned with
the marker as illustrated.
Changing the Interior Handle Orientation
3.7
Securely screw clockwise as shown
to complete your handle orientation
change.
3.8

4.1 4.3
4.4 Peel paper layer OFF the Adhesive
tape and prepare for installation.
4.2
Install Spindle (C) with the holes
side into the base of the lock
and align the holes locate in
the 3 o’clock and 9 o’clock
position.
Insert locking pin (D) in to
the hole as shown above.
Carefully bend the end of the locking
pin (D) with a needle nose pliers.
Failure to bend the locking pin and turn
the handle freely without obstruction will
result to malfunction.
D
STEP 4: PREPARING LOCK FOR INSTALLATION
If you drilled a hole in Step 1, use Slotted Barrel Extension (U) and securely tighten with a flat head screwdriver
by turning it clockwise onto the lock. If you did not drill a hole in step 1, you can leave this pole removed.

Exterior
STEP 5: INSTALLING THE LOCK (EXTERIOR)
Install the exterior lock as shown
to the left by aligning the lock
straight and passing the cable and
attached rods through the lockset.
5.1
Pass the Spindle (C) through
the center of the lockset, and
the round rods through the sides
in their respective holes. The cable
should run underneath the lockset.
5.2
Align the lock straight and press
hard (if you use the Adhesive tape
in step 4.4) to secure the top of the
lock.
5.3

STEP 6: INSTALLING THE LOCK (INTERIOR)
Interior
6.1
V
Insert Positioning Rods (V) into
the holes to the left and
right of the Spindle (C).
The holes are located at the 3
o’clock and 9 o’clock positions.
6.2
Install the side with the black
Mounting Plate (LK)
plastic seal against the door.
Positioning rods slide through these holes.
Interior Mounting Plate (LK) will go
against the interior side of your door.
Remove the paper layer off of the
Adhesive Tape and align the
positioning rods on the bottom of
the plate to the corresponding left
and right holes.

6.3
O
3
x
LK
Screw (O)
Screw (O)
6.4
* If you have drilled a hole on the
top in Step 1, please secure the
hole with screw M1 or M2 depending
on your door thickness. Skip this if
no hole was drilled in Step 1.
*Secure top with M1 or M2
P M 5 X 2 5 m m
P M 5 X 3 5 m m
M 1
M 2
Pull the cable from the lock exterior
through the rectangular hole
underneath the positioning rods
and spindle.
Secure the hole above the
spindle with screws (O).
Remove the position rods (V)
and replace them with screws (O)
Tighten clockwise until the mounting
plate is secure.

Plug the cable that is coming through
the door into the lock interior. Make sure
you match the direction of the plug
correctly and matching the red side of
the plug with the red side on the lock.
Secure the connection by ensuring the
snap is inserted tightly.
6.5
Align the square rod to the lock interior
and attach the Interior lock to the Interior
mounting plate.
While you are doing so, gently push
some of the excess cable through the
rectangular hole into the door.
Place the remaining cable against the
interior side of the lock interior so the
lock interior sits securely onto the
mounting plate.
6.6
In case you need to reinstall the lock and
disconnect the cable, make sure to press
the snap to release the plug before carefully
pulling it out. Do not force to pull the plug as
this may result to lose connection and
damage the lock.

+
+
-
-
P (3X)
Once the lock interior is flush against the
mounting plate, secure the lock to the
plate by screwing clockwise using
provided screws (P).
6.7
Insert 4 AA batteries into the lock by
aligning the positive (+) and negative (-)
orientation markings on the batteries to
the battery chamber.
Secure the battery cover by sliding the
cover over the lock and turning the screw
clockwise on top until tight.
6.8

STEP 7: INSTALLING THE DOOR STRIKE
H
G（2X）
Make sure the slanted side of Latchbolt (F1/F2) is closing against
the slanted part of Strike Plate (H) before fixing it on to door frame.
F
DOOR STRIKE INSTALLATION
Close your door to see if your lock closes securely with your existing door strike. If the lock closes
securely, you may keep the existing door strike without removing the old hardware. However, it’s
recommended that you use our door strike.

Congratulations! You have completed the Lockly®Secure physical lock installation. To complete
your setup, download the Lockly®app from the iOS or Google Play app Store and follow on-screen
instructions.
STEP 8: DOWNLOAD THE LOCKLY®APP
Scan or visit Lockly.com/app