Lockly SECURE LUX MORTISE EDITION User manual

SECURE LUX
MORTISE EDITION
INSTALLATION
GUIDE

Go to Lockly.com/pages/installation to watch a
video version or download this installation guide.

Welcome!
This guide will walk you through step-by-step how to install
and get your Lockly Secure Lux up and running.
If you have
any questions please reference our
online support at:
Lockly.com/support or call [phone] for help.
Reference installation parts overview foldout on back page

3
Preparation
Remove existing mortise lockset, deadbolt or latch and use provided template
to bore new holes.
1-⅜"~4-¾"
(40~120mm)
1" (25mm)
Hole for handle
1" (25mm)
9-½" (241mm)
2-⅜" (60mm)
or 2-¾" (70mm)
1" (25mm)
IMPORTANT: This product is recommended for professional installation.
You may be required to use a hole saw and/or professional drilling
tools to prepare door for installation.

1. Configure your lockset according to your direction.
RIGHT IN-SWING DOOR RIGHT OUT-SWING DOOR
LEFT IN-SWING DOOR LEFT OUT-SWING DOOR
IMPORTANT: Before installation, make sure to determine your door
opening directions. This will be your reference in adjusting the
latch throw, cylinder spin, interior and exterior handles.
Preparation
4

5
Change the latch throw and cylinder spin direction according to your door
opening. The factory setting of the throw and cylinder spin is for Right In-Swing
door. If you have a different door opening direction, please refer to Preparation
(Page 4) for the correct latch direction and spin position.
Changing latch throw direction for Right -Out Swing and Left-In Swing doors
Changing cylinder spin direction for Left- In Swing and Left-Out Swing Doors
ADJUSTING THE LATCH THROW & SPIN
Step 1
Use a Phillips screwdriver to
remove the cylinder spin screw
and take out the spin
1
Shift the direction of the
cross hole of the spin facing
the exterior for left-in swing or
left -out swing door opening.
2
Install the spin and
secure with screws
3
Note: This concave
point below the cross
hole must be facing
downward
Use a Phillips screwdriver to
remove three screws and
faceplate. Rotate the latch
throw to 180 °.
1
Make sure the latch has
fully rotated 180 ° and
then re-install the
faceplate.
2
Secure faceplate with
3 screws and tighten.
3

6
Install the mortise lockset into door pocket hole and tighten it with the 4 screws
supplied. Route the cable inside the door pocket and place it aside.
INSTALLING THE LOCKSET
Step 2
H
G
Route the cable inside the door
Make sure the cross hole of lockset
is
at the center alignment and
facing
the door exterior during
installation.
Lockset(1X)
KA4 X 25mm
Screw(4X)
Exterior

7
The illustrations below shows how to shift the exterior and interior door handle from
right to left direction. The factory setting of the handle is for a right handed door.
Skip this step if you have a right handed door. To shift handle from right to a
left handed door, follow the instructions below:
To Left Swing
REVERSING DOOR HANDLES
Step 3
Exterior Handle
1. Use allen key to remove screw on the right (factory default screw position for
right swing door)
Exterior Handle
1. Remove the two screws with an Allen key
2. Use your fingers to pull the reversing barrier backwards to a loosened position,
then rotate the handle 180° as shown. Release barrier to return to its original
position once the handle is reversed.
3. Tighten the screw on the left with allen key.
2. Push the spring hook downward and hold with your finger. Then rotate the handle 180°.
3. Lock the two screws with an Allen key
Allen Wrench
From Right Swing
W
Allen Wrench
W

8
INSTALLING THE LOCK CYLINDER
Step 4
Select Positioning Rods (D) according to door thicknesses
40~55mm door
thickness,No
cutting required
50~66mm door
thickness, no
need to cut
40~120mm door
thickness, cut
according to
the instructions
on the right
67mm
77mm
128mm
40mm≤Door thickness≤55mm
55mm<Door thickness≤70mm 70mm<Door thickness≤85mm
85mm<Door thickness≤100mm
23.5mm
1 2 3 4
Note: When the door thickness is less than
70mm, cut 23.5mm off the cylinder blade
or from the fourth scale
Exterior Panel(1X)
Remove this plastic
cover before installing
the lock cylinder.
Lock cylinder
(1X)
Washer (X2)
Positioning Rod (X2)
Cylinder Screw
PM4 X 10mm
Screw (X2)
B
E
D
C
A
1
2
3
4
Check door thickness and confirm if the cylinder blade needs to be cut;
Insert the cylinder Bto the cylinder hole of the exterior assembly A;
Secure the cylinder Bto the exterior assembly Awith two screws E;
Insert washer Con positioning rods D . Install it onto corresponding screw
hole on the exterior assembly A, and tighten it with a vise or wrench.

9
5.1 The spindle must be inserted from the door interior passing through the lockset
all the way to door exterior.
INSTALLING THE SPINDLE
Step 5
Escutcheon
Fixing Screw x2
Escutcheon Pad x2
Spindle x1
Positioning
sleeve x1
Mounting
Plate
V
K
J
I
F
Door Interior: The spindle must
be inserted from the door
interior. It must pass through
completely the lockset top
hole as shown below.
Door Exterior: After the
spindle inserted, pull it outward
by hand in the direction of
the arrow, and ensure the
spindle cannot be pulled out.
Note: Insert the spindle through
the door. The "L" sections as
shown in the diagram should
be kept within 33-35mm. Cut
and discard the excessive
portion, if applicable.
Check door thickness
L L
119mm
within Outside
185mm
within Outside
40~120mm door thickness, cut according to the
instructions on the right
40~70mm door thickness, no need to cut
This part needs to be inserted through the exterior part of the door
5.2 After spindle is cut and installed, prepare part I, J K & Vfor the exterior
assembly installation

10
6.2 Route the exterior assembly cables and rods through the corresponding holes
on the lockset.
6.3 Insert the positioning sleeve into the inner side of the spindle. Make sure they
are all aligned and correctly oriented.
6.4 Check handle if they are in smooth operation. Then check if the locking and
unlocking operations are smooth. If not, adjust the mounting plate and screws
until the the operation is running smooth.
INSTALLING THE EXTERIOR ASSEMBLY
Step 6
40~55mm door
thickness, no need
to cut
50~66mm door
thickness, no need
to cut
60~765mm door
thickness, no need
to cut
40~120mm door
thickness, cut
according to the
instructions on
the right
31.5mm 38mm
52mm 97mm
40mm≤Door thickness≤53mm
53mm<Door thickness≤66mm 79mm<Door thickness≤92mm
66mm<Door thickness≤79mm
92mm<Door thickness≤105mm
Spindle x1
Escutcheon Pad x2
Escutcheon
Fixing Screw x2
Mounting
Plate
Exterior Panel x1
Positioning
sleeve x1
Remove and discard
positioning sleeve after
fixing the screws.
A
V
K
J
I
F
6.1 Select or adjust the escutcheon Kscrews (x2) according to door thickness.
Install the exterior assembly, mounting plate, escutcheon pad and secure with K
screws.
Select and adjust Screws Kaccording to door thicknesses

11
INSTALLING THE INTERIOR ASSEMBLY
Step 7
When the security
bolt is retracted,
the flat shaft (M)
must be in vertical
position
Use nose pliers to bend
the cotter pin as shown
Remove and
discard positioning
sleeve after
fixing the screw
(1X)
PM5 X 12mm Screw(2X)
Cotter Pin(1X)
When the door thickness is greater than
70mm, insert the cotter pin through this hole. When the door thickness is less than 70mm,
insert the cotter pin through this hole.
KM5 X 10mm Screw(1X)
Interior Panel(1X)
Battery Cover(1X)
Flat Shaft(1X)
V
M
Q
R
L
N
P
7.1 Install torque blade Mto interior assembly.
7.2 Insert the cotter pin Lto the Torque Blade Maccording to door thickness. See
notes as illustrated in the diagram.
7.3 Remove and discard the positioning sleeve Vthen plug the exterior assembly
cables to the corresponding socket of the interior assembly
7.4 Insert torque blade to the corresponding hole and install the interior assembly
on to door. Ensure the interior assembly hole for spindle and screw holes are
aligned. Secure the interior assembly with screws N& Q.

INSTALLING BATTERIES
Step 9
FINAL CHECK
After installation is completed, lift both
the interior and exterior handles up and
down making sure they are running
smoothly. Then check if the deadbolts
and latch are thrown smoothly with
the physical keys.
Step 8
Insert 4 x AA batteries make sure
the batteries are correctly
positioned.
Then close the
battery cover and
install screw
caps. Check the functions
of
the lock per user manual after
installing the batteries.
Screw Caps(2X)
O
12

13
INSTALLING DOOR STRIKE
Step 10
KA4 X 18mm
Screw(2X)
Strike(1X) Dust Box(1X)
UT S
Use installation template to drill hole on the door frame.
Install the dust box S on to door frame. Then install the strike plate T and fix it
with screws U .

DOWNLOAD THE LOCKLY APP
Step 11
Congratulations! You have completed the Lockly physical lock installation. To
complete your setup, download the Lockly app from the App Store or on
Google Play and follow on-screen instructions.
Scan or visit
Lockly.com/app
14

15
Add more Smart to your Home
Real-time, monitoring, & status
Monitor open/closed door status
with real-time alerts sent to your
smart phone, no matter where
you are.
Add the optional Lockly Secure Link Wi-Fi Hub,
together with the free Lockly app, it's easier than
ever to securely control and manage your door
from anywhere, anytime.
Secure Link Wi-Fi Hub
Grant access, even when you’re
not home Lock and unlock door
from anywhere.
Hands-free voice control Control and check
your status using only your voice with Amazon
Alexa or Google Assistant-enabled devices.
Available online at:
Lockly.com/hub

16
FCC Warning：
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device
must accept any interference received, including interfer-
ence that may cause undesired
operation.
NOTE 1: This equipment has been tested and found to comply with the limits for
a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide
reasonable protection against harmful interference in a
residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
FCC Radiation Exposure Statement
This device Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for
an uncontrolled environment. It should be installed and operated with minimum
distance 20cm between the radiator & your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation,
Science
and Economic Development Canada’s licence-exempt RSS(s). Oper-
ation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.

17
WARNING: This product can expose you to chemicals including Lead,
which is known to the State of California to cause cancer. For more
information go to www.P65Warnings.ca.gov.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-
lage
est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation limits in section
2.5 of RSS-102. It should be installed and operated with a minimum distance of
20cm between the radiator and any part of your body.
Cet équipement est conforme à l'exemption des limites d'évaluation habituelle
de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une distance
minimale de 20 cm entre le radiateur et toute partie de votre corps

INSTALLATION OVERVIEW & PARTS LIST
KA4 X 18mm Screw
Allen Wrench
Positioning Sleeve
Dust Box
Strike Plate
RFID Card
Activation Card
PM4 X 10mm Screw
Spindle
Exterior Assembly
Cylinder
Keys
KA4 X 25mm Screw
Cylinder Positioning Rod
Lockset
Positioning Rod Pad
Mounting Plate
KM5 X 10mm Screw
Interior Assembly
Battery Cover
Screw Cap
Torque Blade
PM5 X 12mm Screw
Escutcheon Pad
Cotter Pin
Escutcheon Screw
Parts List
Labeled As Description
A
B1
C
B2
D
E
F
G
H
I
J
K
L
N
M
O
P
Q
R
S
T
U
V
W
X
Y
0004001 1341652
LOCKLY.COM | HOTLINE: [phone] | EMAIL: [email protected]
ACC20211201
KEEP THIS CARD!
ACTIVATION CARD
Exterior
W
B2
C
D
F
Y
G
H
T
U
N
M
V
R
Q
P
K
I
E
B1
A
O
LJ
SX

@meetlockly | #Lockly
Connect with us