Lockly FLEX TOUCH PRO User manual

FLEX TOUCH PRO
3D FINGERPRINT SCANNER FOR DEADBOLTS
INSTALLATION GUIDE
Enjoy the freedomTM

You will need the following tools:
*Modify door hole using a wood file or utility knife. When trim-
ming the door hole, make sure to have enough space for the
fingerprint sensor cable. Avoid cable from getting pinched or
tightly squeezed between the door surface and lock's ring or
shield.
2
Required Tools
Important, before getting started...
Phillips Screwdriver
*Optional
Flathead Screwdriver Wood File
Lockly Flex Touch Pro is designed to work with existing standard
deadbolts. Before installing, check your existing deadbolt for smooth
and clean operation. With the door closed, the deadbolt should lock
and unlock without any resistance or binding.
I
f any resistance or binding exist, adjust or modify strike plate for smooth,
resistance free operation. Failure to do so will impede the performance
of the Lockly Flex Touch Pro.
If needed, Lockly offers standard mechanical deadbolts designed
to work with Lockly Flex Touch Pro to replace old or worn deadbolts.
To purchase, visit www.lockly.com/accessories or call our Customer
Hotline: [phone].

Remove the existing lock installed on your door and retain the
deadbolt.
3
Step 1
Existing Deadbolt
1
REMOVE EXISTING DEADBOLT

A. NO RING B. MOUNTING RING C. ANTI-PRY SHIELD
Does not require
door lock hole
modification.
There are primarily 3 different styles of deadbolts (shown below)
found on most doors. Depending on which type yours is, you
may need to do a slight modification on your door hole (trim by
wood file or utility knife) to ensure the cable of the fingerprint
sensor is not pinched between the door and the lock.
*Optional
4
Step 1 continued
Door Exterior
2
REMOVE EXISTING DEADBOLT
Lock type B and C require
door hole modification. File
or trim door hole to avoid
cable from being pinched.
IMPORTANT:

5
Step 2
Front
Exterior
With the mounting plate
facing out, route the cable
on the fingerprint sensor
through the deadbolt hole
as shown.
Square Mounting
Plate
Round Mounting
Plate
Depending on the style and shape of your existing deadbolt, select
either the square or round , provided mounting plate.
A
A
B
C
C
D
B
DEMO
60mm
70mm
Standard diameter of
rounded deadbolt lock
INSTALLING FINGERPRINT SENSOR
Adjust the position of the sensor according
to the diameter of your deadbolt lock.
Carefully tighten screws after adjusting
the position.
D
D
1
2

6
Step 2 continued
Door Exterior
CABLE UNDER
DEADBOLT BODY
!
Existing
Deadbolt
Guide the cable through the
door hole under the existing
deadbolt.
Remove protective paper
from adhesive strips.
Carefully check alignment
then press mounting plate
and sensor flush to door.
Remove positioning sleeve,
assembly should remain in
place by the adhesive strips.
Insert the Positioning Sleeve
INSTALLING FINGERPRINT SENSOR
Open area positioned at the bottom
* If you trimmed or filed your door
hole, the cable should be seating
on the trimmed or filed area.
E
E
6
4
5
IMPORTANT:

7
Step 3
Make sure the deadbolt
is extended.
If necessary, remove key
from deadbolt .
Reinstall the deadbolt . According to the following figure, select
an appropriate installation method based on different brands
of deadbolts.(The diagram shows the right swing door)
Note: The brand LOGO of the deadbolt is on the top.
Left swing door :
Rotate the torque blade
clockwise until it can't
turn.
Door Exterior Door Exterior
Right swing door :
Rotate the torque blade
counterclockwise.
INSTALLING THE EXTERIOR ASSEMBLY
II
II
I
I
I
V
V
12
3
Kwikset Deadbolt Yale Deadbolt
NOTE : The torque blade
should be in the vertical
direction.

Check to make sure the deadbolt remains fully extended. If
needed, use a screwdriver or pliers to fully extend.
Door Exterior
Door Exterior
Step 3 continued
INSTALLING THE EXTERIOR ASSEMBLY
8
Schlage Deadbolt Left swing door :
First turn clockwise to
the bottom, and then
turn counterclockwise
to the direction shown
in the picture (Angle
45°).
Right swing door :
First turn counterclock-
wise to the bottom, and
then clockwise to the
direction shown in the
figure (Angle 45°).
NOTE : The torque
blade shall be
horizontal.
Left swing door :
Turn clockwise until
you can no longer
turn.
Right swing door :
Rotate counterclo-
ckwise until you can
no longer rotate.
Defiant Deadbolt
4
The torque blade must be turned to the correct
angle, consistent with the hole in the lock body.
IMPORTANT:

9
Step 4 INSTALLING THE INTERIOR ASSEMBLY
1
Kwikset Deadbolt : Open the door left, select the gold adapter,
open the door right, select the black adapter.
Yale Deadbolt select red adapter.
Schlage Deadbolt select silver adapter.
LEFT SWING DOOR
RIGHT SWING DOOR
Black
Gold
OR
OR
Red
Sliver
1
2
3
I
Select the appropriate spindle/torque blade adapter that matches
your lock based on the deadbolt . There are approximately
4 different deadbolts on the market, and for each deadbolt
there are detailed instructions on the installation diagram.

INSTALLING THE INTERIOR ASSEMBLY
Step 4 continued
10
1
Attached the temporary positioning guide tool to the selected
adapter to form the adapter assembly. You will use the adapter
in the succeeding steps.
(Select an adapter based on the brand of deadbolt you are
not using, as shown in the previous step ).
Adapter Assembly
H
H
K
K
Z
2
If none of the provided adapters match
your locks spindle or torque blade, please
call our Customer Hotline [phone]
to get help with an alternative solution.
IMPORTANT:
Defiant Deadbolt select green adapter.
Green
4