Lockly Secure LUX User manual

MORTISE EDITION
USER MANUAL
LUX MORTISE LOCK
SECURE

10
11
12
14
16
17
20
22
23
24
25
26
Section 1 - Product Highlights
Section 3 - Using Your Smart Lock
3
4
5
6
6
7
7
8
9
1
Section 2 - Product Overview
2.1 Product Overview- Exterior
2.2 Product Overview- Interior
2.3 Understanding Your New Lock
2.4 Factory Reset
2.5 Keypad Display Switch
2.6 Setting Switch
2.7 Rebooting LocklyTM Secure
2.8 Low Battery
2.9 Changing the Battery
1.1 Product Features
3.1 Configuring Access
3.2 Entering Programming Mode
3.3 Adding an Access Code
3.4 Deleting an Access Code
3.5 Checking the Access Code
3.6 Adding a Fingerprint
3.7 Fingerprint Scanning Directions
3.8 Fingerprint Scanning Tips & Troubleshoot
3.9 Deleting Stored Fingerprints
3.10 Adding an RFID card
3.11 Deleting RFID Card
3.12 Adding Secure Link
27
28
29
29
30
31
33
34
35
35
Section 4 - Locking and Unlocking
4.1 Locking/Unlocking with Access Codes
4.2 Locking/Unlocking Lockly™ with Fingerprints
4.3 Locking/Unlocking Lockly™ with App
4.4 Locking/Unlocking using RFID
4.5 Locking/Unlocking Lockly™ with Physical Key
4.6 Locking and Unlocking with Voice Assistant Control
4.7 Safe Mode - Overview
4.8 Lock and Unlock using Anti-theft Button
4.9 Anti - Theft Button Switch
4.10 Locking from the Outdoor
36
37
38
39
Section 5 - Advanced Features
Section 6 - Important Notes
Section 7 - Cleaning Tips
Section 8 - Safety Precaution
5.1 Offline Access Code (OAC)
TABLE OF CONTENTS
For additional support, visit http://lockly.com/help
or email [email protected]
Table of Contents

SECTION 1.1 1
Patented Anti-Peep Keypad
Digits are randomly displayed on the key pad ensuring access codes to
be undetectable to intruders after repeated use. To experience the pat-
ented and innovative key pad software, powered by PIN GenieTM, please
download the PIN GenieTM Vault App from iOS App Store or Google Play.
Multiple Access Codes & Monitoring
Store up to 8 Access Codes for family, friends, and guests, as well as moni-
tor entry and exit records.
Advanced 3D Fingerprint Recognition
Biometric Fingerprint Recognition protocol allows up to 99 registered
fingerprints to be used and accepts only actual fingerprints - preventing
lifted prints from being used.
RFID Card Access
You Lockly™ Secure Lux can be accessed by use of RFID card.
Complete Privacy
The exterior displayed keypad can be locked and switched off using the
simple ON/OFF toggle from the inside panel. The owner can prevent
others trying to input the passcode from the outside and entering the
home
Offline Access Code (OAC)
The offline access code can allow owners to issue access codes, set the
allowed access duration, all without Lockly™ ever connecting to the inter-
net, so in case of power outage, you can still magically and remotely issue
Access Codes without any connection to the web.
Anti-theft Button
Thieves may use improvised wires or other picking tools to access your
inside door handle. Prevent them from unlocking your door when this
button is activated.
1.1 Product Features

SECTION 1.12
Automatic Lock
Owners no longer have to worry about forgetting to lock the door. With Auto
Lock enabled, Lockly™ Secure will automatically re-lock the door based on
your customized timing set between 5-300 seconds.
Backup Keys and 9V Battery Socket
The door can be opened with physical backup keys. There is also a 9V
battery connection socket for emergency power backup to access the
key pad in case your smart lock runs out of battery.

SECTION 2.1 3
2.1 Product Overview- Exterior
Lock Status icon
Bluetooth light
Power Status
Bluetooth icon
OK Button
CARD
Front (Front Body）
Fingerprint Reader
Handle
Key Hole Cover
9V Battery Back
Up Socket
Key Hole
RFID Card Reader
Touchscreen
Keypad Buttons

SECTION 2.24
2.2 Product Overview - Interior
Settings Switch Reset Button
Program Button
Touchscreen Switch
Battery
compartment
*Operated by 4 X AA
size alkaline batteries
( not included )
Thumbturn
Anti-theft Button
Inside Handle
Back (Main Body）
Battery Compartment Cover

SECTION 2.3 5
2.3 Understanding Your New Lock
The Default Access Code is
NOTICE 1 2 3 4 5 6
After the installation of your new Lockly™ , understanding some key func-
tions of operating your smart lock is important. The following guides will
walk you through resetting a lock, adding Access Codes, deleting Access
Codes, adding and deleting fingerprints , adding and deleting RFID cards
and also how to configure your OAC (Offline Access Code).
For any questions you can always visit http://lockly.com/help for assis-
tance.
Don't forget that Lockly™ Secure works best with our iOS and Android app.
Please download the app by visiting the link below.
Scan or visit Lockly.com/app

SECTION 2.46
Reset Button
2.4 Factory Reset
In order to restore the Lockly™ to factory default settings, you must have your “Initial
Code” available. The Initial Code can be found on the Initical Code Card that
came with your smart lock. (See Quick Start Guide)
After you have the Initial Code ready, push the reset button on the back panel of
the Lockly™ to perform your reset. See below to see which Reset Process ap-
plies for you. Once the smart lock has been reset, all the data previously stored
will be deleted.
2.5 Keypad Display Switch
The exterior keypad screen can be locked and turned off using the
ON/OFF switch at the back panel of the smart lock. When it is switched
off, people outside cannot enter any passcode to unlock the door.
Keypad
Keypad screen
OFF ON

SECTION 2.6 7
With Random mode on, every time you enter a digit
while entering passcode, the display keypad will be
refreshed.
With Auto Lock enabled, the smart lock will automatically
relock the door 5s to 30s after unlocking.
Switch 1: Auto Lock (Default: ON)
Switch 3: Audio (Default: ON)
Switch 4: Random (Default: OFF)
Setting Switch
Enables the Audio sound (Beeper) when in the ON position.
Switch 2: Alarm Mode (Default: OFF)
With Alarm Mode on, the door reacts against external
activity according to the sensitivity level that has been set.
2.6 Setting Switch
2.7 Rebooting LocklyTM Secure
Press and release the reboot button when you want to reboot the lock. Your
Lockly™ will beep once after reboot. Only reboot when necessary.
To reboot, find the reboot button located below the keyhole from the exteri-
or of Lockly™ Secure Lux.
You will need something small such as a paperclip, to press the reboot
button. Insert the paper clip and press down firmly.
NOTICE
Reboot Lockly™ in case of dead battery or
malfunction. No settings will be changed and all
Access Codes will still be stored within Lockly™.
Reboot Button

SECTION 2.88
When the battery is in seriously low condition, Lockly™ will make contin-
uous beeping sounds in addition to the flashing low battery icon on the
touch screen. You should replace batteries immediately to avoid your
smart lock from shutting down.
When your smart lock low-battery warning alert finally dies, you will have
3 chances to unlock your smart lock either by a password, APP or
fingerprint. If the unlock was successful, the low-battery warning alert will
be on for 1 minute. After which, the smart lock will go to dead-battery
mode and will lock auto lock in 5 seconds and the screen will display a
low-battery icon.
Dead Battery
Condition Indicator Solution
Low Battery
Battery Icon on the
display keypad will
light up to indicate
low battery.
Replace batteries immedi-
ately to avoid battery
failure. Lockly™ Secure can
still operate up to 300 cycles
in low battery condition.
When there is no
display and sounds;
and screen is
non-functional.
Replace batteries immediately.
Supplied physical backup keys
can be used to unlock the
door. Alternatively, use a 9V
battery as shown below to
temporarily activate the lock.
Your Lockly™ will automatically
detect battery polarity. So hold your
9V
battery lead in place against
bottom of
the Lockly™ to temporarily
activate
t he screen to enter your
Access Code.
Be sure to hold the
9V battery against
the contact
points located at the bottom
of the
lock until you have successfully
unlocked your door with your
Access
Code. Once unlocked,
batteries should
be replaced imme-
diately.
2.8 Low Battery
_ +
9V
Alkaline
battery
CARD

SECTION 2.9 9
2.9 Changing the Battery
Open the battery compartment cover and insert 4 AA alkaline battery as
shown below.
• Make sure the batteries are correctly oriented.
• Replacement of batteries does not affect programmed data.
• Replace only with new batteries. DO NOT mix with used batteries.
+
+
-
+
-
-
+
-
AA 1.5V X 4
1 2 3

SECTION 3.110
3.1 Configuring Access
The Default Access Code is
NOTICE 1 2 3 4 5 6
How to Use the Keypad
There are a total of five (5) buttons on the
keypad as shown in the example image
to the left. The numbers in each button
may differ than what is shown on your
device than what is displayed here.
To enter your required digit, just simply
press the circle where your number is
shown. You do not need to press the
actual number as anywhere within the
circle will suffice.
The button on the bottom is the OK
button. You will be pressing this button
when you are done entering your Access
Code.
Your new Lockly™ Access Code can be any combination of 6 to 8 digits.
Once a new Access Code is entered, the Default Access Code of 123456
would be deleted.
A Maximum of 8 sets of Access Codes can be stored for use.
OK Button

SECTION 3.2 11
3.2 Entering Programming Mode
To enter Programming Mode,remove the
battery compartment cover on the
interior side of the Secure to expose the
Reset and Program buttons.
Simply press the Program button to enter
programming mode.
Note: Program button will be disabled
once synced to a smart phone. Config-
ure all settings via synced smart phone.
To end Programming Mode,press the Program button anytime.
Programming Mode will automatically exit if the keypad is inactive for
more than thirty (30) seconds.
After entering Programming Mode, you
should see the screen as displayed to
the right on your Lockly™ keypad.
Follow the following steps to add,
delete, or check your Access Codes.
Program Button
Add Passcode
ModeNumber
Delete Passcode
View Passcode
Alarm Sensitivity

SECTION 3.3
12
3.3 Adding an Access Code
While in Programming Mode, select “1AD” to add an Access Code. If you
are not in Programming Mode,please see Section 3.2 to enter Program-
ming Mode.
After pressing “1AD” press “Pd” to add an Access Code.
Enter your new 6 - 8 digit Access Code
and press when you are finished.
You will then re-enter the code to confirm
your new Access Code.
Remember, just touch the digit you need
within the circle around each 3 numbers.
There is no need to touch the exact
location of the number. For example,
based on the example image to the left, if
you need “1”,you can touch the upper
left button or the lower right button. For
“6”, you would touch the upper right
button.

SECTION 3.3 13
3.3 Adding an Access Code (Continued)
If you have successfully entered your
new Access Code twice, you will see
the new code displayed here. In this
example, we chose 654321. Press
to Confirm or to cancel.
To exit or cancel, you can always press
or
If the two (2) Access Codes you
entered does not match, an error
message will appear on the screen (As
shown to the left). Press OK to return to
the Programming Screen and try again.
See Section 3.3
OK Button

SECTION 3.414
3.4 Deleting an Access Code
While in Programming Mode, select “2DE” to delete an Access Code. If you are
not in Programming Mode, please see Section 3.2 to enter Programming Mode.
After pressing “2DE” press “Pd” to delete an Access Code.
OK Button
Example Only
Active Access Codes will then be
displayed on the screen in sequence from
left to right, top to bottom. In the
example shown on the left, the Access
Code displayed is 1 3 5 7 9 0 .
Rotate through different Access Codes
shown by touching any number on the
screen. If you find the Access Code you
want to delete, simply hold the OK button
for 3 seconds. (Continue on next page)

SECTION 3.4 15
NOTICE There are two incidents where your Access Code
cannot be deleted.
3.4 Deleting an Access Code (Continued)
Once you have selected the Access Code
you want to delete, Lockly™ will ask you to
confirm deletion by showing you the
Access Code you are deleting, in this
example,
1 3 5 7 9 0.
Press to delete, or to cancel.
Only one Active Access Code
No Access Codes Set
There are no Access Codes
set. The factory default Access
Code cannot be deleted.
There is only one (1) Access Code saved
in the smart lock. At least one code must
be registered. Please add another Access
Code before attempting to delete the
existing code.

SECTION 3.516
3.5 Checking the Access Codes
While in Programming Mode, select “3CH” to check registered Access Codes.
If you are not in Programming Mode, please see Section 3.2 to enter Program-
ming Mode.
Active Access Codes will then be displayed on the screen in sequence from left
to right, top to bottom. In the example shown on the left, the Access Code
displayed is 1 3 5 7 9 0 .
OK Button
Rotate through the different Access Codes by touching any number on the screen.
To exit Check Access Code screen, simply press the OK button.
If there are no Access Codes registered in
your smart lock, Check Access Code
mode will be invalid. The default Access
Code will not be shown on the display
keypad, and you will see the following
screen shown to the left instead.

SECTION 3.6 17
3.6 Adding a Fingerprint
We are using an advanced biometric sensor, providing the most secure
fingerprint authentication. For security reasons, Lockly™ will only accept
fingerprint patterns that consist of cross intersection points. Patterns with no
cross intersection points will not be acceptable.
Please check your fingers before registration to make sure the finger you
want to register will be acceptable by our system. Otherwise, use an
alternative finger to ensure successful registration.
The following examples show which types of fingerprint patterns will be
acceptable. It is highly recommended to enroll at least one finger from
each hand in case the hand you are using is unavailable, such as, in
instances like if you are holding items in that hand or have sustained an
injury.
Your LocklyTM can register up to ninety-nine (99) fingerprints. Please read
the following sections if you want to add or delete fingerprints. We
recommend using your app to add fingerprints, however, the following
section can show you without using the app.
Fingerprint Pattern with
Cross Intersection Lines
Concentric or Parallel Pattern
with no Cross Intersection Lines
Fingerprint with Scars or
Worn Out Ridges
OK Not OK Not OK

SECTION 3.618
While in Programming Mode, select “1AD” to add an Access Code. If you are
not in Programming Mode, please see Section 3.2 to enter Programming Mode.
After pressing “1AD” press “FP” to register a Fingerprint.
Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see
a green LED ring light up on the fingerprint panel on the exterior of Lockly™.
3.6 Adding a Fingerprint (Continued)
Once you’re in Fingerprint Registration Mode
you will see two numbers displayed on keypad.
The top number is your Fingerprint Registration
number, in this example to the left, “1”. The
bottom number will always start with a “6”.
You must successfully scan your fingerprint six (6)
times for it to properly register. Every time you
scan your fingerprint, the number on the bottom
will change, starting from 6 - then 5, 4, 3, 2, 1, until
the fingerprint is successfully registered.
Note: For reference, please keep a record of your
fingerprint registration number to distinguish
whom it was registered to.