LSIS XGT Series User manual

Right choice for ultimate yield
LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.
Programmable Logic Controller
Dnet I/F Module
User’s Manual
 Read this manual carefully before
installing,
wiring, operating, servicing
or inspecting this equipment.

Keep this manual within easy reach
for quick reference.
XGL-DMEB
XGT Series
http://www.lsis.com

Revision History
Revision History
※The number of User’s manual is indicated right part of the back cover.
ⓒLSIS Co., Ltd 2005All Rights Reserved.
Version Date Remark Page
V1.0 ’17.01 First edition -

Safety Instructions
Before using the product …
For your safety and effective operation, please read the safety instructions
thoroughly before using the product.
►Safety Instructions should always be observed in order to prevent accident
or risk by using the product properly and safely.
►Precautious measures can be categorized as “Warning” and “Caution”, and
each of the meanings is as follows.
This symbol indicates the possibility of serious injury
or death if some applicable instruction is violated
This symbol indicates the possibility of severe or
slight injury, and damages in products if some
applicable instruction is violated
Moreover, even classified events under its caution category may develop into
serious accidents depending on situations. Therefore we strongly advise users
to observe all precautions in a proper way just like warnings.
►The marks displayed on the product and in the user’s manual have the
following meanings.
Be careful! Danger may be expected.
Be careful! Electric shock may occur.
After reading this user’s manual, it should be stored in a place that is visible
to product users.
Warning
Caution

Safety Instructions
Safety Instructions for design process
Please install a protection circuit on the exterior of PLC so that the
whole system may operate safely regardless of failures from
external power or PLC. Any abnormal output or operation from PLC
may cause serious problems to safety in whole system.
- Install protection units on the exterior of PLC like an interlock circuit
that deals with opposite operations such as
emergency stop,
protection circuit, and forward/reverse rotation or install an interlock
circuit that deals with high/low limit under its position controls.
- If any system error (watch-dog timer error, module installation error,
etc.) is detected during CPU operation in PLC, all output signals are
designed to be turned off and stopped for safety. However, there
are cases when output signals remain active due to device failures
in Relay and TR which can’t be detected
. Thus, you are
recommended to install an addition circuit to monitor
the output
status for those critical outputs which may cause significant
problems.
Never overload more than rated current of output module nor
allow to have a short circuit. Over current for a long period time may
cause a fire .
Never let the external power of the output circuit to be on earlier
than PLC power, which may cause accidents from abnormal output or
operation.

Please install interlock circuits in the sequence program for safe
operations in the system when exchange data with PLC or modify
operation modes using a computer or other external equipments
Read specific instructions thoroughly when conducting control
operations with PLC.
Warning

Safety Instructions
Safety Instructions for design process
Safety Instructions on installation process
I/O signal or communication line shall be wired at least 100mm
away from a high-voltage cable or power line.Fail to follow this
instruction may cause malfunctions from noise
Caution
Use PLC only in the environment specified in PLC manual or
general standard of data sheet. If not, electric shock, fire, abnormal
operation of the product may be caused.
Before install or remove the module, be sure PLC power is off. If
not, electric shock or damage on the product may be caused.
Be sure that every module is securely attached after adding a
module or an extension connector.
If the product is installed
loosely or incorrectly, abnormal operation, error or dropping may be
caused. In addition, contact failures under poor cable installation will
be causing malfunctions as well.
Be sure that screws get tighten securely under vibrating
environments.
Fail to do so will put the product under direct
vibrations which will cause electric shock, fire and abnormal
operation.
Do not come in contact with conducting parts in each module,
which may cause electric shock, malfunctions or abnormal operation.
Caution

Safety Instructions
Safety Instructions for wiring process
Prior to wiring works, make sure that every power is turned off. If
not, electric shock or damage on the product may be caused.

After wiring process is done, make sure that terminal covers are
installed properly before its use.Fail to install the cover may cause
electric shocks.
Warning
Check rated voltages and terminal arrangements in each product
prior to its wiring process.
Applying incorrect voltages other than
rated voltages and misarrangement among terminals may cause fire
or malfunctions.
Secure terminal screws tightly applying with specified torque.If
the screws get loose, short circuit, fire or abnormal operation may be
caused. Securing screws too tightly will cause damages to the module
or malfunctions, short circuit, and dropping.
*
Be sure to earth to the ground using Class 3 wires
for FG
terminals which is exclusively used for PLC. If the terminals not
grounded correctly, abnormal operation or electric shock
may be
caused.
Don’t let any foreign materials such as wiring waste inside the
module while wiring, which may cause fire, damage on the product
or abnormal operation.
Make sure that pressed terminals
get tighten following the
specified torque. External connector type shall be pressed or
soldered using proper equipments.
Caution

Safety Instructions
Safety Instructions for test-operation and
maintenance
Don’t touch the terminal when powered. Electric shock or abnormal
operation may occur.
Prior to cleaning or tightening the terminal screws, let all the
external power off including PLC power. If not, electric shock or
abnormal operation may occur.
Don’t let the battery recharged, disassembled, heated, short or
soldered. Heat, explosion or ignition may cause injuries or fire.
Warning
Do not make modifications or disassemble each module.Fire,
electric shock or abnormal operation may occur.
Prior to installing or disassemb
ling the module, let all the
external power off including PLC power.
If not, electric shock or
abnormal operation may occur.
Keep any wireless equipment such as walkie-talkie or cell phones
at least 30cm away from PLC
. If not, abnormal operation may be
caused.
When making a modification on programs or using run to modify
functions under PLC operations,
read and comprehend all
contents in the manual fully. Mismanagement will cause damages to
products and accidents.

Avoid any physical impact to the battery and prevent it from
dropping as well.
Damages to battery may cause leakage from its
fluid. When battery was dropped or exposed under strong impact,
never reuse the battery again. Moreover skilled workers are needed
when exchanging batteries.
Caution

Safety Instructions
Safety Instructions for waste disposal
Product or bat
tery waste shall be processed as industrial waste.
The waste may discharge toxic materials or explode itself.
Caution

◎
Table of Contents
◎
Chapter 1 Introduction ………………………………………………………… 1-1 ~ 1-5
1.1 What is DeviceNet? ……………………………………………………….……………… 1-1
1.2 Characteristics of the module …………………………………….……………………… 1-2
1.3 Information for Module Operation ………………………………………………………… 1-3
1.4 Configuration of Smart I/O for Dnet ………………………………………….……… 1-4
Chapter 2 Specifications ……………………………………………………… 2-1 ~ 2-8
2.1 General Specifications ……………………………………………………………………… 2-1
2.2 Performance Specifications ……………………………………………………………… 2-2
2.3 Part names and structure ………………………………….……………………………… 2-4
2.4 Cable Specifications ………………………………………….…………………………… 2-5
2.5 Terminating Resistor …………………………………………….…………………… 2-6
2.6 Tap/Divider ………………………………………………………………………………… 2-7
Chapter 3 Installation and Test Operation ………………………………… 3-1 ~ 3-8
3.1 Installation …………………………………………………………….…………………… 3-1
3.2 From Setting to Operation ………………...………..…………………………………… 3-7
3.3 Setting Procedure of N Configurator and XG5000…..………..………………………… 3-8
Chapter 4 System Configuration ………………….………………………… 4-1 ~ 4-3
4.1 System with LS Dnet I/F module used ………………………...………………………… 4-1
4.2 Combined system with LS Dnet I/F module and slaves by other manufacturers…….. 4-2
4.3 System with Multi-master used ………………………………………..…………….…… 4-3
Chapter 5 N Configurator Setting ………………………………………… 5-1 ~ 5-160
5.1 EDS Analyzer ………………………………..……………………………………………… 5-1
5.2 Project File Management ………………………………………………………………… 5-4
5.3 Binary File Management ………………..……………………………………………… 5-7
5.4 Excel Report …………………………..…………………………………………………… 5-10
5.5 Program Exit …………………………..…………………………………………………… 5-17
5.6 N Configurator Overview …………..…………………………………………………… 5-18
5.7 N Configurator Features ………………..………………………………………………… 5-19
5.8 System Requirements for Running N Configurator …………………………………… 5-21
5.9 N Configurator Installation ……………………………………………………………… 5-22

5.10 Editing Devices ………………………..………………………………………………… 5-26
5.11 Changing Display Method ………..…………………………………………………… 5-30
5.12 Screen Configuration ……………..…………………………………………………… 5-37
5.13 Fast Start ……………………………..…………………………………………………… 5-48
5.14 Device List …………………………..…………………………………………………… 5-53
5.15 EDS Viewer ………………………..…………………………………………………… 5-54
5.16 Project Explorer ……………………..…………………………………………………… 5-56
5.17 Master Property Window …………..…………………………………………………… 5-58
5.18 Bus Parameter Window …………..…………………………………………………… 5-59
5.19 Slave Property Window …………….…………………………………………………… 5-60
5.20 Output Window ……………………..…………………………………………………… 5-61
5.21 Shrink Topology ……………………..…………………………………………………… 5-62
5.22 Toolbar/Status Bar …………………..…………………………………………………… 5-64
5.23 Project property settings …………..…………………………………………………… 5-65
5.24 Master Properties …………………..…………………………………………………… 5-67
5.25 Bus Parameter ……………………..…………………………………………………… 5-70
5.26 Slave Properties ……………………..…………………………………………………… 5-71
5.27 Slave I/O modules …………………..…………………………………………………… 5-77
5.28 Slave Parameters …………………..…………………………………………………… 5-85
5.29 Communication Settings ………………………………………………………………… 5-92
5.30 Download Binary Images …………..…………………………………………………… 5-94
5.31 Download Binary Files ……………..…………………………………………………… 5-96
5.32 Upload Binary Files ……………..……………………………………………………… 5-98
5.33 Master Slave Control . ………………………………………………………………… 5-100
5.34 Slave Device Monitoring …………..………………………………………………… 5-102
5.35 Device Diagnostics ………………..………………………………………………… 5-113
5.36 Network Scan ………………………..………………………………………………… 5-117
5.37 Device Table ………………………..………………………………………………… 5-121
5.38 Device Communication Type Table ..………………………………………………… 5-124
5.39 Slave I/O Address Table …………..………………………………………………… 5-126
5.40 Option Window ……………………..………………………………………………… 5-133
5.41 Window Management ……………..………………………………………………… 5-140
5.42 Project Window Management ……..………………………………………………… 5-148
5.43 Project Tab Group Management . …………………………………………………… 5-150
Chapter 6 High-speed Link Setting ………………………………………… 6-1 ~ 6-20
6.1 Introduction ………………………………………………………………………………… 6-1
6.2 How to use XG5000 …………………….…………..……………………………………… 6-2
6.3 High-speed Link Editing …………………………………….……………………………… 6-5
6.4 Read and Write of High-speed Link ………………………..……………..…………… 6-11
6.5 Enable Link ………………………………………………………………………………… 6-12
6.6 System Diagnosis ………………………………………………………………………… 6-16
6.7 High-speed Link Information …………………..………………………..……………… 6-19
Chapter 7 Communication Program ………………………………………… 7-1 ~ 7-33
7.1 Example Program……………………………………………..…………………………… 7-1
7.2 Example Program(XDL-BSSA setting) ………………………………………………… 7-17

Chapter 8 Troubleshooting ……………………………………………………8-1 ~ 8-7
8.1 Symptoms and Management by LED Status …………………..……………………… 8-1
8.2 System Diagnosis in XG5000……………………………………..……………………… 8-1
8.3 Diagnosis of Communication Module through XG5000 ……………………………… 8-4
8.4 Troubleshooting of Respective Errors …………..……..……………………………… 8-5
Appendix ……………………………………………………………………… A-1 ~ A-21
A.1 List of Flags …………………………………..………..…………………………………… A-1
A.2 Terminology ………………………………………….…….……………………………… A-11
A.3 Smart I/O Mode Setting in N-Configurator……………………………………………… A-18
A.4 External Dimensions ……………………………………………………………………… A-21

Chapter 1 Introduction
1-1
Chapter 1 Introduction
1.1 What is DeviceNet?
This user’s manual is to describe DeviceNet Master I/F module among communication modules of
XGT PLC system. It is proposed as ISO 11898 and 11591-1 standards which are composed of
Physical Layer and Data Link Layer only.
DeviceNet is an Application Layer developed by Rockwell/Allen-Bradley, widely used in the present
industrial automation field.
Since DeviceNet uses CAN communication protocol, low-priced CAN microchip applied will reduce
the cost. And direct connection of master and respective devices with the network of device level is
available. In addition, flexible counteractions against errors are also available by access to important
diagnosis information of device level which was impossible to use via the I/O interface.

Chapter 1 Introduction
1-2
1.2 Characteristics of the Module
DeviceNet (hereinafter referred to as Dnet) I/F module have features as follows;
▶1 master module can control 63 slave modules with the max. 28,000 points of I/O control
available.
▶Multi-drop and T-diverged connection is available allowing the system to be extended and
changed easily with flexible system operation function provided.
▶Open network available to connect with other company’s various slave modules.
▶Master and slave can be set through Configuration Tool (N Configurator), and communication
control is available through XG5000.
▶Automatic setting, in other words, Auto scan is available for the modules (which exist) in the
network.
▶Configuration Tool (N Configurator)
1) Station number (MAC ID) can be specified (0 ~ 63) through Configuration Tool
(N Configurator).
2) Communication speed can be specified (125/250/500 kbps) through Configuration Tool
(N Configurator).
3) Out of 4 communication types (Poll, Bit strobe, COS, Cyclic), one DeviceNet can be
selected through Configuration Tool (N Configurator).
▶Setup time and installation cost of the system will be saved from reduced connections and
wiring works by using a single cable for communication power(24V) and communication signal
line.
▶Network setting and various diagnoses can be simply arranged through N Configurator and
XG5000, in other words, diagnosis of the whole network or each slave is available.
▶Real-time control over I/O devices in the lowest level of the network system is available.
In addition, connection to various slaves I/O is available.
- General I/O, actuator, proximity switch, optical switch, valve, inverter, A/D module, D/A
module, position control, etc.

Chapter 1 Introduction
1-3
1.3 Information for Module Operation
1) It describes required components to operate the product.
Classification Type Description Reference
Series XGL-DMEB DeviceNet I/F module. Master only
Software
N
Configurator
Software for Station number, Speed,
Communication methods, configuration of
network setting.
Master set up only
EDS
Including module information (Product
code/Type, Maker name/Maker number)
- It is used to configure the network in N
Configurator.
Provided by each
maker
XG5000
Software for PLC programming
Additional software
Remark
XG5000 program can be downloaded at our company website. If you do not have an access to
the internet, contact the nearest agency for CD-ROM about XG5000. EDS file related to our slave
module (Smart Link) can be downloaded at Http://www.lsis.com
2) It describes about the number of module and position that can be installed in a single CPU module.
Classification
Description
Position
XGK/XGI
Standard base and Extension base
XGR
Extension base
Number Common
A maximum of 12. In case of using with other communication
modules, It is able to install a maximum of 24 (But High-speed
link setting is limited to 12)
High-speed link
number
Common A maximum of 12 (It cannot set for P2P)
3) Please refer to below User Manuals to write communication program with Dnet I/F module.
•XGK Instruction Manual
•XGR/XGI Instruction Manual
•XG5000 User Manual
•XGK CPU User Manual
•XGR/I CPU User Manual
•Smart I/O User Manual
•Other company’s User Manual which is related to Dnet

Chapter 1 Introduction
1-4
1.4 Configuration of Smart I/O for Dnet
1) Slave Products List of Stand-alone type
Product
Details
Classification
Code
Designations
Plug-in type
47060053
GDL-D22C
DC input 16 points
47060106
GDL-D22C(Q)
DC input 16 points, Quick mode
47060052
GDL-D24C
DC input 32 points
47060107
GDL-D24C(Q)
DC input 32 points, Quick mode
47060054
GDL-TR2C
TR output 16 points (0.5A, Source)
47060108
GDL-TR2C(Q)
TR output 16 points (0.5A, Source), Quick mode
47060087
GDL-TR2C1
TR output 16 points (0.5A, Sink)
47060115
GDL-TR2C1(Q)
TR output 16 points (0.5A, Sink), Quick mode
47060055
GDL-TR4C
TR output 32 points (0.5A, Source)
47060109
GDL-TR4C(Q)
TR output 32 points (0.5A, Source), Quick mode
47060081
GDL-TR4C1
TR output 32 points (0.5A, Sink)
47060116
GDL-TR4C1(Q)
TR output 32 points (0.5A, Sink), Quick mode
47060056
GDL-DT4C
DC input 16 points/TR output 16 points (0.5A,Source)
47060110
GDL-DT4C(Q)
DC input 16 points/TR output 16 points (0.5A,Source), Quick mode
47060083
GDL-DT4C1
DC input 16 points/TR output 16 points (0.5A, Sink)
47060117
GDL-DT4C1(Q)
DC input 16 points/TR output 16 points (0.5A, Sink), Quick mode
47060057
GDL-RY2C
Relay output 16 points
47060111
GDL-RY2C(Q)
Relay output 16 points, Quick mode
Remark
1) Plug-in type: A product whose I/O terminal block can be installed or removed.
2) Quick mode: A product whose initializing time is 1.5 sec. after the communication power is On.
2) Slave Products List of Extendable type
Products
Details
Classification
Code
Designations
Communication
Adapter 47060131 XDL-BSSA Dnet I/F Adapter
Extendable I/O
47230004 XBE-DC32A 24VDC Input 32points
47230010 XBE-DC16A 24VDC Input 16points
47230011 XBE-DC08A 24VDC Input 8points
47230006 XBE-RY16A Relay Output 16points
47230009 XBE-RY08A Relay Output 8points
47230005 XBE-TN32A
Transistor Output 32points(NPN Type)
47230013 XBE-TN16A
Transistor Output 16points(NPN Type)
47230012
XBE-TN08A
Transistor Output 8points(NPN Type)
47230014 XBE-DR16A
24VDC Input 9points/Relay Output 16points
Extendable 47230007 XBF-AD04A Current/Voltage Input 4Ch

Chapter 1 Introduction
1-5
Special module 47230008 XBF-DV04A Voltage Output 4Ch
47230018 XBF-RD04A RTD input 4Ch
47230017 XBF-DC04A Current Output 4Ch

Chapter 2 Specifications
2-1
Chapter 2 Specifications
General specifications of XGT series are as specified below in Table 2.1.
No. Item Specification Related specifications
1
Operating
temp.
0℃∼+55℃-
2 Storage temp. -25℃∼+70℃-
3
Operating
humidity
5∼95%RH, no dew allowed -
4
Storage
humidity
5∼95%RH, no dew allowed -
5 Vibration
immunity
For discontinuous vibration -
Frequency
Acceleration
Amplitude
Number
IEC61131-2
5 ≤f < 8.4 ㎐- 3.5mm
Each 10 times in
X,Y,Z directions
8.4 ≤f ≤150 ㎐
9.8
㎨
(1G)
-
For continuous vibration
Frequency Acceleration Amplitude
5 ≤f < 8.4 ㎐- 1.75mm
8.4 ≤f ≤150
㎐
4.9 ㎨(0.5G) -
6 Impact
immunity
* Max. impact acceleration: 147
㎨
(15G)
* Authorized time: 11 ㎳
* Pulse wave : Sign half-wave pulse
(Each 3 times in X,Y,Z directions)
IEC61131-2
7 Noise
immunity
Square wave
impulse noise
AC: ±1,500V
DC: ±900V
Test specification of
LS Industrial Systems
Static electric
discharging 4.0KV (contact discharging) IEC 61131-2, IEC 61000-4-2
Radiation electromagnetic
field noise
80 ~ 1,000MHz, 10 V/m
IEC 61131-2,
IEC 61000-4-3
Fast
Transient
/burst
noise
Class Power
module Digital/Analog I/O communication interface IEC 61131-2,
IEC 61000-4-4
Voltage
2KV
1KV
8
Ambient
conditions
No corrosive gas or dust
9
Operating
height
2,000m or less
10
Pollution level
2 or less
11 Cooling type Natural air cooling
[Table 2.1] General Specifications
Notes
[Note 1] IEC (International Electrotechnical Commission):
An international nongovernmental organization which promotes internationally cooperated standardization
in electric/electronic field,
publishes international standards and manages applicable estimation system
related with.
[Note 2] Pollution level:
An index indicating pollu
tion level of the operating environment which decides insulation performance of
the devices. For instance, Pollution level 2 indicates the state generally that only non-conductive pollution
occurs. However, this state contains temporary conduction due to dew produced.
2.1 General Specifications

Chapter 2 Specifications
2-2
2.2 Performance Specifications
1) Performance specifications
Performance specifications of DeviceNet (hereinafter referred to as Dnet) I/F module are as described below.
Item Performance Specifications
Transmission
Specification
Transmission Speed (kbps)
125/250/500
Transmission
Type
I/O
Connection
G2, UCMM
I/O
Communication
Poll, Bit strobe, COS, Cyclic
Communication
distance(m)
Thick Cable
500 (125kbps)/250 (250kbps)/100 (500kbps)
Thin Cable
100 (125/250/500kbps)
Terminal resistance (Ω)
121 (1%, 1/4W)
Max.drop
length(m)
125 kbps
6 (Max. extended length 156)
250 kbps
6 (Max. extended length 78)
500 kbps
6 (Max. extended length 39)
Data Packet
0~8 Bytes
Message Access Control
CSMA/NBA
Network Structure Trunk/drop line
Power/Signal cable inside the identical network cable
Bus Type Poll type
Max. number of nods Up to 64 (including master) MAC IDs (MAC Identifier)
System Features
Insertion and removal of nod available in voltage On status
Operation Voltage
DC 24V
Diagnosis Function
Module: Checks duplicated station/ Checks CRC error
N Configurator: Detects defective station/Checks BusOff/Auto-scan
function
XG5000: Monitors High-speed link
Master/Slave Operation Available only in master
Parameter setting 1) N Configurator (CONFIG Port of Dnet I/F) 2) Setting to High-speed link of XG5000
(RS-232C of CPU module or USB port)
XG5000
(High-
speed
link)
Data process unit
Byte
Send/Receive period Select among 20ms, 50ms, 100ms, 200ms, 500ms, 1s, 5s and 10s
- Default : 20ms
Max. communication point Send 128,520points, Receive 128,520 points, 16,065 bytes
respectively
Max. block number
63 (Setting range: 0~62)
Max. point number per block
2040 points (255 bytes)
Basic
Specification
Max. modules installed Up to 12 (available on basic base and added base)
Internal-consumed current
(mA)
350mA
Weight (g) 81g
1) Transmission distance of Dnet I/F module is inversely proportional to data transmission rate.
If thin cable is used, the transmission distance will be limited to 100m regardless of data
transmission rate.
2) CSMA/NBA (Carrier Sense Multiple Access with Non-destructive Bitwise Arbitration)
3) If the station No. of Dnet I/F module (master module) is specified, surely reset the applicable
slave module.
Remark

Chapter 2 Specifications
2-3
2) Communication methods
Communication methods can be set per module when it is supported by slave module.
Setting of Slave insertion/setting in N Configurator is as shown below.
(1) Automatic setting: Online Automatic Network Scan
(2) Manual setting: Settings Device Configuration
Communication method’s features are as shown below.
Communication
method
Feature
Poll
Master and slave module Send/Receive the data by one on one.
Bit-Strobe
It is used only in input module.
The way to transmit data simultaneously for master module from its input
type slave modules when the master module’s data transmission request
is received.
COS
(Change of State)
If input data status of slave module is changed, slave module transmits
changed data to master module. But output type slave module,
Settings Device Configuration Menu selection  Connection Object
Instance Attributes Setting window  Expected Packet Rate Category, transmits
every time according to its setting rates.
Cyclic
Slave module attempts to Send/Receive periodically.
Communication period setting, Settings Device Configuration Menu
selection Connection Object Instance Attributes Setting window  Expected
Packet Rate Category , sent/receives data periodically between master and
slave module according to its setting periods.
So, Communication method should be used with cautions along with data process of
Input/Output module in the system.
3) EDS (Electronic Data Sheet) file
▶It is to allow other vendors to use restricted information of product through EDS file format.
Restricted information of product: Maker name and unique number (ODVA Certification)
Module information (Master and slave module)
Input/Output module information (Input point, Output point)
Information on communication support method
▶EDS file addition: It can be executed by File Copy EDS.
Copied EDS file can be used only when located under EDS folder of N Configurator execution
directory

Chapter 2 Specifications
2-4
LED
Status
LED displaydescription
RUN
On
Normal
Completion of initializing.
Off
Error
Error is occurred.
I/F
Flickering
Normal
Normal status of interface in CPU module.
On/Off
Error
Error status of interface in CPU module.
HS
On
Normal
Normal status when High-speed link is enabled.
Flickering Waiting
Communication is disconnected between Dnet I/F and Slave module
while downloading at High-speed link enabled status by
N Configurator.
Off Error
High-speed link service is in Critical error while High-speed link is
enabled.
D-RUN
Flickering Stop
Stop status of communication between Dnet I/F module and slave
module.
On
Communicating
Communication status of Dnet I/F module and slave module.
MNS
Off Power Off
Waiting status of Dnet I/F module communication.
Non-completed status of Checking duplicated MAC ID on
network.
It is not supplied external power supply (DC24V).
Green
Flickeri
ng
Waiting
Communication waiting status between Dnet I/F module and slave.
- It is recognized the information of network (Station number, ID,
Communication speed) in N Configurator.
Green
Flickering
Normal Normal communication status between Dnet I/F module and slave.
Red
Flickering
Error Slave module is separated network while communicating.
Red
Flickeri
ng
Critical
error
Dnet I/F module could not access the network.
Non-ability status of Communication (Bus Off).

Duplicated ID module is existed in network.
2.3 Part names and Structure
(1) LED displayparts
(2) 5 pin connector (for exeternal connection)
Color
Signal
Service
5 pin connector
Red DC 24V(+) Vcc
121 Ω
Blue
White
Black Bare
White CAN_H Signal wire
Bare Drain Shielded wire
Blue CAN_L Signal wire
Black DC 24V(-) GND
XGL-DMEB