Ltech SE-12-100-500-W1D User manual

1www.ltech.cn
50/60Hz
≤0.18A/115Vac ≤0.08A/230Vac
84%300mA 8 %500mA@ (at full load), 2 @ (at full load)
ta:-20~50°Ctc:90°C
-40~80°C/10~95%RH
±0.03%/°C(0-50°C)
PF>0.95/115Vac , PF>0.9C/230Vac(at full load) (at full load)
THD≤10%/230Vac(at full load)
C (Test twidth=130us tested under 50% Ipeak)/230Vacoldstart15A
L-N:2KV
Max.0.24mA
SE-12-100-500-W1D
≤48V
100-500mA
9-42Vdc
0.9W~12W
±5%
≤3600Hz
DALIDT6
115Vac/230Vac
100-240Vac
120-300Vdc
ErP
IEEE1789
CIESVM
DF
85g±10g
110×35×20mm(L×W×H)
Intelligent Tunable White LED Driver (Constant Current)
Housing made from SAMSUNG/COVESTRO's V0 flame retardant PC
materials.
Ultra small, thin and lightweight, screwless end cap.
Set the output current down to 1mA.
DALI bus standard IEC62386-101, 102, 207.
Class 2 LED driver, Safety Extra Low Voltage (SELV).
Soft-on and fade-in dimming function enhances your visual comfort.
T-PWM™ dimming technology allows quality and high-end lighting.
The whole dimming process is flicker-free with high frequency
exemption level.
Comply with the EU’s ErP Directive, networked standby<0.5W.
When there is no load, the output will be 0V to prevent damage to LEDs
due to poor contact.
Overheat, over voltage, overload, short circuit protection and
automatic recovery.
Suitable for ClassⅠ/Ⅱ/Ⅲindoor light fixtures.
Normal service life can reach 100,000 hours.
5-year warranty (Rubycon capacitor).
Set the DALI group, scene in the advanced DALI template.
Multiple current levels, wide voltage range, suitable for LEDs with
different power
Change the dimming interface, output current, DALI address and
other parameters on the NFC programmer or via the App, and sync
the parameters to the driver.
The certification icon represents undergoing certification applications only, and final certification qualification subject to actual product.
Overheat
Protection
Short circuit
protection
Over Load
protection
V
Over voltage
protection
Multi current
setting
Constant power
setting
DIM / CT
Technical Specs
Model
Dimming Interface
Output Feature
Output Type
Protection Grade
Insulation Grade
Isolation
Constant current
IP20
Class II (Suitable for class I/ II /III light fixtures)
Features
Dimming Range
Maximum output voltage(No-load)
Output Current Range
Output Voltage
Output Power Range
Current Accuracy
PWM Frequency
OUTPUT
LF Current Ripple
0~100%, down to 0.01%
<3%(Maximum current for non dimming state)
INPUT
Frequency
Input Current
Efficiency (Typ.)
Power Factor
THD
Inrush Current
Anti Surge
Leakage Current
Input Voltage
DC Voltage Range
AC Voltage Range
ENVIRONMENT
Working Temperature
Working Humidity 20~95%RH,non-condensing
Storage Temperature/Humidity
Temperature Coefficient
Vibration 10~500Hz, 2G 12min/1cycle, 72 min for X, Y and Z axes respectively
PROTECTION Overvoltage Protection
Overload Protection
Short Circuit Protection
Overheat Protection Intelligently adjust or turn off the current output if the PCB temperature ≥110°C. When the PCB temperature <90°C, automatically recover normal output
Automatically protect the device when voltage exceeds the no-load voltage. It can be recovered automatically
Automatically protect the device when the load exceeds 102% of the rated power. Automatically recover once load is reduced
Enter hiccup mode if short circuit occurs, and recover automatically
I/P-O/P: 100MΩ/500VDC/25°C/70%RH
Insulation Resistance
Withstand Voltage I/P-O/P: 3750Vac
SAFETY
&
EMC
SafetyStandards
EMC Emission
EMC Immunity
China
European Union
Korea
Russia
Germany
CB Member States
Australia
Europe
India
Britain
Canada
GB19510.1, GB19510.14
EN61347-1, EN61347-2-13, EN62384
KC61347-1, KC61347-2-13
IEC61347-1, IEC61347-2-13
EN61347-1, EN61347-2-13, EN62493
IEC61347-1, IEC61347-2-13
CCC
CE
KC
EAC
TUV
CB
RCM AS61347-1, AS61347-2-13
ENEC EN61347-1, EN61347-2-13, EN62384
UKCA BS EN 61347-1, BS EN 61347-2-13, BS EN 62493
BIS IS 15885 (PART 2/SEC 13)
CUL CSA C22.2 NO.250.13
UL UL 8750
America
EN61000-4-2,3,4,5,6,8,11, EN61547
CCC
CE
KC
EAC
GB/T17743, GB17625.1
EN55015, EN61000-3-2, EN61000-3-3, EN61547
KSC 9815, KSC 9547
IEC62493, IEC61547, EH55015
RCM EN55015, EN61000-3-2, EN61000-3-3, EN61547
CUL ICES-005
UKCA BS EN IEC 55015, BS EN IEC 61000-3-2, BS EN 61000-3-3, BS EN 61547
UL FCC PART 15B
China
European Union
Korea
Russia
Australia
Britain
Canada
America
Power Consumption
Flicker/Stroboscopic Effect
Standby power consumption
Networked standby <0.5W (After shutdown by command)
No-load power consumption <0.5W (When the lamp is not connected)
No standby mode
Meet IEEE 1789 standard/High frequency exemption level
Pst LM≤1.0，SVM≤0.4
Phase factor DF0.9
OTHERS Dimensions
Weight(N.W.)
DALI DT6
SE-12-100-500-W1D

2www.ltech.cn
110
35
20
Unit：mm
Product Size
Wiring Diagram
DALI Connection
Dimming: 0~100%
Color temperature: 2700-6500K
Wire diameter: 0.75-1.5 (20-16AWG)
Strip length: 5-6mm
Wire diameter: 0.5-1.5 (22-16AWG)
Strip length: 5-6mm
Minimum hole size: φ40mm (1,57")
DALI DT6
SE-12-100-500-W1D
N
LDALI
0.5-1.5
SEC
输出
LED+
DA
DA
0.75-1.5
PRI
输⼊
N
L
/
0.5-1.5

3www.ltech.cn
SE-12-100-500-W1D
100 285-mA
9-42V
0 9 12. - W
285-500mA
2.562 12-W
5
7
9
1 1
1 3
1 5
1 7
1 9
2 1
2 3
2 5
2 7
2 9
3 1
3 3
3 5
3 7
3 9
4 1
4 3
4 5
1 0 0 1 5 0 2 0 0 2 5 0 2 8 5 3 0 0 3 5 0 4 0 0 4 5 0 5 0 0
Current and Parameters Sheet
Set output current on the NFC programmer or via the App
Output Current(I)Range
Output Voltage(U)Range
Output Power(P)Range
See the curve below for details
Output Voltage - Output Current
Output Current(mA)
Output Voltage(V)
Protective Housing Application Diagram
2. Pry up the protective housing
in the side plate position with a
tool.
5. Close the protective housing.
3. Connect to electrical wires
with a screwdriver as wiring
diagram shows.
4. Press down the tension plate
to fix the the electrical wires.
1. Use a tool to pry up the protective
housing on the side panel.
Installation Precautions
≥15cm
≥15cm
≥15cm
≥15cm ≥15cm
Please do not stack the products. The distance between two products should be ≥15cm so as not
to affect heat dissipation and the lifespan of the products.
Please not place the products on LED drivers. The distance between the product and the driver
should be ≥15cm so as not to affect heat dissipation and shorten the lifespan of the products.
DALI DT6
SE-12-100-500-W1D

4www.ltech.cn
DALI DT6
SE-12-100-500-W1D
www.ltech.cn
APP Solutions
BLE Connection
NFC Driver Settings
Iout: 100mA 9- 42V
Address: 10+0
Fade Time: s
Ready to write
SE-12-100-500-W1D SE-12-100-500-W1D
500mA
9-24V
SE-12-100-500-W1D
13+0
SE-12-100-500-W1D
Write succeeded
Work with a NFC programmer (LT-NFC)
Change the output current, DALI address and other parameters on the NFC programmer. After modification, batch parameters can be be written to the driver.
1.Read the LED driver
Power the programmer by using the USB cable, then select “NFC Driver Settings” and press “OK” button. Next, keep the programmer’s sensing area close to the NFC logo of the driver to read the
driver parameters.
On the home page of the programmer, press the “ ” button to select 【 Ready to Write】, then press the “OK” button. After the screen displays “Ready to write...”, please keep the programmer’s
sensing area close to the NFC logo of the driver. When the screen displays “Write succeeded”, it means the parameters have been successfully changed.
3.Write to the driver
2.Change the driver parameters (Output current/address)
On the home page of the programmer, press “ ” button to select the parameters you want to change and press the “OK” button to edit them. Then, press “ ” button to adjust the parameter values
and press “ ” to select the next needed value. After the parameter values are modified, save them by pressing the "OK" button.
Note: (1) If the current value you set is out of range, The programmer will report an error; (2) The DALI address range: 0-63.
Use the NFC Lighting APP
Scan the QR code below with your mobile phone and follow the prompts to complete the APP installation (According to performance requirements, you need to use a NFC-capable Android phone, or an
iphone 8 and later that are compatible with iOS 13 or higher).
Use your NFC-capable phone to read the driver parameters, then set the output current, address, other parameters, or set the advanced DALL template depending your needs. Save your settings and
hold your phone close to the driver again, so the parameters can be easily written to the driver.
Read/Write the LED driver
1.Read the LED driver
On the APP home page, click【 Read/Write LED driver】, then keep the programmer’s sensing area close to the NFC logo of the driver to read the driver parameters.
Before you begin setting the parameters of the driver on the NFC programmer, please make sure the driver is powered off.
Before you begin setting the parameters of the driver on the NFC programmer or via the APP, please make sure the driver is powered off.
NFC logo of the driver
2.Edit the parameters
Click【Parameter settings】to edit the advanced parameters, like output current, DALI address, dimming curve, advanced DALI template, etc.
3.Write to the driver
After completing the parameter settings, click 【Write】in the upper right corner, and keep the programmer’s sensing area close to the NFC logo of the driver, so the parameters can be written to
the driver.
Ready for scanning
SE-20-100-700-W2D
Uout:9.00-28Vdc Pout:4.2-20W
SE-12-100-500-W1D
Uout:9.00-24Vdc Pout:4.5-12W
SE-12-100-500-W1D
Uout:9.00-24Vdc Pout:4.5-12W
700
500 500

5www.ltech.cn
DALI DT6
SE-12-100-500-W1D
NFC Driver Settings
BLE Connection
APP Solutions
SOL1
Address: 10+0
SE-12-100-500-W1D
SOL2 SOL3
Iout: 500mA 9-24V
Ready to write
Sync SOL2
succeeded
SE-12-100-500-W1D
Write succeeded
Write/Read on the NFC programmer
1.Connect to the NFC programmer
Enable Bluetooth on your phone and power the NFC programmer first. Then press the button on the programmer to switch to “BLE Connection” and press ”OK” button to wait for Bluetooth connection.
On the APP home page, click【Write/Read on NFC programmer】—【Next】to search for the programmer and connect to it.
2.Read the LED driver
On the “Programmer information” page, choose any solution for editing. Then keep the programmer’s sensing area close to the NFC logo of the driver, to read the driver parameters.
Connect the NFC programmer to your phone and read the driver parameters with your phone. After editing the solution in the mobile App, you can sync it to the NFC programmer and write advanced parameters to
mass LED drivers.
4.Write to the LED driver
When the programmer screen shows “Sync ... succeeded”, click “BACK” button to return to the home page and switch to the “APP Solutions”, then press the “OK” button to access the optional solu-
tions. Select the corresponding solution by pressing the “ ” button, then keep the programmer’s sensing area close to the NFC logo of the driver. After this, the advanced solution can be written to
a large number of the same model drivers.
3.Edit the parameters
Click【Parameter settings】to edit the advanced parameters, like output current, DALI address, dimming curve, advanced DALI template,etc. Then click 【Save】in the top right.
For more advanced solution settings, please scan the QR code below and check out the NFC programmer manual (model: LT-NFC).
Advanced DALI template
Integrate the functions of the DALI lighting system, edit the DALI group and lighting effects for scenes, then save them in the advanced template to achieve lighting programming.
Setup page 1 (for Read/Write LED driver) : Go to App home page — 【 】 icon in the top right —【DALI template on phone】.
Setup page 2 (for Read/Write on NFC programmer): Go to App home page —【Read/Write on NFC programmer】—【DALI templateonprogrammer】.
DALI template DALI template
SE-20-100-700-W2D
Uout:9.00-28Vdc Pout:4.2-20W
SE-12-100-500-W1D
Uout:9.00-24Vdc Pout:4.5-12W
SE-20-100-700-W1D
SE-20-100-700-W1D
SE-12-100-500-W1D
SE-12-100-500-W1D
500

SE-12-100-500-W1D
PF
THD
6www.ltech.cn
30.0 0
40.0 0
50.0 0
60.0 0
70.0 0
80.0 0
90.0 0
1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 1 0 0
1 0 0 m A 1 5 0 m A 2 0 0 m A
2 5 0 m A 3 0 0 m A 3 5 0 m A
4 0 0 m A 4 5 0 m A 5 0 0 m A 0.3 0
0.4 0
0.5 0
0.6 0
0.7 0
0.8 0
0.9 0
1.0 0
1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 1 0 0
1 0 0 m A 1 5 0 m A
2 0 0 m A 2 5 0 m A
3 0 0 m A 3 5 0 m A
4 0 0 m A 4 5 0 m A
500mA
7.0 0
17.0 0
27.0 0
37.0 0
47.0 0
57.0 0
67.0 0
77.0 0
87.0 0
1 0 2 0 3 0 4 0 5 0 6 0 70 8 0 9 0 1 0 0
1 0 0 m A 1 5 0 m A
2 0 0 m A 2 5 0 m A
3 0 0 m A 3 5 0 m A
4 0 0 m A 4 5 0 m A
5 0 0 m A
2 0 ,000
3 0 ,000
4 0 ,000
5 0 ,000
6 0 ,000
7 0 ,000
8 0 ,000
9 0 ,000
100,0 0 0
110,0 0 0
3 03 0 3 5 4 0 4 5 5 0 5 5 6 0 6 56 5 7 0 7 5 8 0 8 5 9 0
Relationship Diagrams
Efficiency VS Load Power Factor VS Load
Load[%]
Efficiency[%]
Load[%]
THD VS Load
Load[%]
Life time VS Housing temperature
Housing temperature[°C]
Life time[H]
0.1%
1%
5%
30%
40%
70%
90%
100%
10%
20%
50%
60%
80%
Frequency(Hz)
Modulation(%)
1.00%
10.00%
100.00%
0.10%
110 100 1000 100003125
Modulation Area Diagram
High Frequency Exemption Area Diagram
Marks in the right chart weretestedresults of different current ranges.
Theoutputfrequenyis0Hzin100%brightnessanditscorresponding
modulation is0%, whichcould notbeshownintherightchart.
IEEE 1789
f
f
≤ 8Hz
≤ 10Hz
limit (%)
Exemption assessment
(High frequency exemption)
f
f
f
f
f
f
f
f
f
f
≤ 90Hz
≤ 90Hz
≤ 1250Hz
≤ 3125Hz
8Hz <
10Hz <
90Hz <
90Hz <
> 1250Hz
> 3125Hz
0.2
0.1
0.025 ×
0.01 ×
0.08 ×
(0.08/2.5) ×
limit (%)
Limit of modulation in low risk area
Limit of modulation in no effect area
Waveform frequency of optical output
Waveform frequency of optical output
Exemption assessment
Brightness
Flicker Test Sheet
DALI DT6
SE-12-100-500-W1D

7www.ltech.cn
DALI DT6
SE-12-100-500-W1D
260 240 215××mm(L×W×H)
SE-12-100-500-W1D
Packaging Specifications
Model
Carton Dimensions
Quantity
Weight
20 PCS/Layer; 5 Layers/Carton; 100 PCS/Carton
0.095 kg/PC; 9.5 kg±5%/Carton
Packaging Image
Inner Packaging Box
Carton Packaging

8www.ltech.cn
Warranty periods from the date of delivery: 5 years.
Free repair or replacement services for quality problems are provided within warranty periods.
Warranty Agreement
Warrantyexclusionsbelow:
Beyond warranty periods.
Any artificial damage caused by high voltage, overload, or improper operations.
Products with severe physical damage.
Damage caused by natural disasters and force majeure.
Warranty labels and barcodes have been damaged.
No any contract signed by LTECH.
1. Repair or replacement provided is the only remedy for customers. LTECH is not liable for any incidental or consequential damage unless it is within the law.
2. LTECH has the right to amend or adjust the terms of this warranty, and release in written form shall prevail.
This product must be installed and adjusted by a qualified professional.
This product is non-waterproof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof enclosure.
Good heat dissipation will extend the life the product. Please install the product in a environment with good ventilation.
When you install this product, please avoid being near a large area of metal objects or stacking them to prevent signal interference.
Please keep the product away from aintensemagneticfield, a high pressure area or a place where lightning is easy to occur.
Please check whether the working voltage used complies with the parameter requirements of the product.
Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a
accident.
If a fault occurs, please do not attempt to fix the product by yourself. If you have any question, please contact the supplier.
This manual is subject to changes without further notice. Product functions depend on the goods. Please feel free to contact our official distributors if you have any question.
Attentions
ZHUHAI LTECH TECHNOLOGY CO., LTD.
Website: www.ltech-led.com
Add: 15th Building, No.3, Pingdong 6th Road, Nanping Technical Industrial Park, Zhuhai, Guangdong, China
Transportation and Storage
1. Transportation
Products can be shipped via vehicles, boats and planes.
During transportation, products should be protected from rain and sun. Please avoid severe shock and vibration during the loading and unloading process.
2. Storage
The storage conditions should comply with the Class I Environmental Standards. The products that have been stored for more than six months are recommended to be re-inspected and can be used
only after they have been qualified.
DALI DT6
SE-12-100-500-W1D

9www.ltech.cn
Update Log
Version Update Content
Updated Time
A0 Original version
20230324
Updated by
Yang Weiling
DALI DT6
SE-12-100-500-W1D