Luminance Brands kathy ireland ASTOR CF235BQ00 User manual

• Español - página 33
• Français - page 65
Part No. F40BP75440001 Form No. BP7544-1
Revision: 12082020 ETL Model No.: CF235
READ AND SAVE THESE INSTRUCTIONS
MODERN
52” Ceiling Fan Owner’s Manual
ASTOR
CF235BS00
Brushed Steel
CF235GRT00
Graphite
CF235BQ00
Barbeque Black
Model Numbers
CF235SW00
Satin White
Net Weight: 16.8 Lbs.
1-800-777-4440
www.luminancebrands.com
Questions, problems, missing parts: Before returning to the store, Call Customer Service

Table of Contents
Safety Instructions
2
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All set screws must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
ETL Model No.: CF235
READ AND SAVE THESE INSTRUCTIONS
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
UC7067RA, manufactured by Rhine Electric Co., Ltd.
To avoid fire, shock or injury, do not use an
Luminance Brands or any other brand of control not
specifically approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
To reduce the risk of personal injury, do not bend
the blades during installation, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
WARNING
!
Section Page
Safety Instructions ................................ 2
1. Unpacking Instructions ..........................3-4
2. Electrical Requirements .......................... 4
3. Ceiling Fan Assembly ..........................5-10
4. How to Hang Your Ceiling Fan ..................11-12
5. How to Wire Your Ceiling Fan ..................13-17
6. Final Assembly ..............................18-20
7. Remote Control Procedures ....................20-23
8. Reverse Switch Operation......................24-25
Section Page
9. Energy Efficient Use of Ceiling Fan ................ 26
10. Maintenance ................................. 27
11. Accessories ................................. 27
12. Repair Parts ...............................28-29
13. Troubleshooting .............................. 30
Ceiling Fan Limited Warranty ....................... 31
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
French ........................................ 65
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

1. Unpacking Instructions
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
ETL Model No.: CF235
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
1.1
Open Carton containing the Fan. Remove top half of
styrofoam unit. Remove Parts and check to see that
you have received the following Hardware and Parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost. If
any parts are missing, contact your local retailer or
catalog outlet for replacement before proceeding.
E
D
F
G
H
I
J
K
C
B
A
PACKAGE CONTENTS
8
10
9
7
2
3
4
5
1
6
1.2
Remove the Fan Motor Assembly from the protective
plastic bag. Place the Fan Motor Assembly onto the
upper foam pad with the Bottom of the Fan Motor
Assembly facing up for blade assembly.
The upper foam pad serves as a holder for the Fan
during the first stages of assembly.
HARDWARE CONTENTS
Part Description Quantity
1 Wire Connectors, 12 ga. 5
2 Clevis Pin 1
3 Hairpin Clip 1
4 Threaded Stud, #8-32 x 1-1/4” 2
5 Lockwashers, External Tooth #8 2
6 Knurled Knobs, #8-32 2
7 #6-32 x 1/4” Pan Head Screws with
Lockwashers 4
8 #8-32 x 11mm Washer Head Screws 16
9 #6-32 x 3/8”Pan Head Screw with Lockwasher
(spare) 1
10 Blade Balance Kit 1
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Cover 1
C Coupler Cover 1
D Lower Housing 1
E LED Light Fixture Assembly 1
F Shade 1
G Hanger Bracket 1
H Hanger Ball / 4.5” Downrod Assembly 1
I Receiver and Hardware 1
J Remote Control Transmitter, SR401
with Wall Bracket and Hardware 1
K Fan Blades 5

Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One 1/4” Blade Screwdriver One Wire Stripper
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
4
ETL Model No.: CF235
2. Electrical Requirements
1. Unpacking Instructions (Continued)
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
Your new Ceiling Fan will require a grounded electrical
supply line of 120 Volts AC, 60 Hz, 15 Amp circuit.
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
IMPORTANT: Your Ceiling Fan will not function
properly, and may be damaged, if used with
any Wall Dimmer Switch or Control other than
the Luminance Brands Fan/Light Remote Control
supplied with the Fan.
Your Luminance Brands Ceiling Fan comes supplied
with a Fan/Light Remote Control which consists of a
receiver mounted inside the ceiling cover. This system
allows you to regulate your ceiling fan speed and light
ON/OFF.
If your Fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 13).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
Controls (Sold Separately)
SW406 Wall Control (sold separately) may be used
with this 52” Astor Ceiling Fan.

3. Ceiling Fan Assembly
FAN BLADE
CENTER
SLOT
FAN
HOUSING
SLIDE FAN BLADE
INTO CENTER SLOT
#8-32 x 11mm WASHER
HEAD SCREWS
(3 per blade)
A
L
Figure 1
3.1
Slide a Blade through the Fan Motor Assembly Center
Blade Slot.
Mount the Blade to Fan Motor Assembly using Three
#8-32 x 11mm Washer Head Screws (supplied)
(Figure 1).
NOTE: Take care not to scratch Fan Motor
Assembly when installing Blades.
Complete the remaining Four Blades installation per the
above instructions.
A spare #8-32 x 11mm Washer Head Screw is supplied
in the loose parts bag, if needed.
5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
ETL Model No.: CF235
To reduce the risk of personal injury, do not bend
the blades during installation, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
WARNING
!
REMOVE & RETAIN
ONE #6-32 x 3/8"
PAN HEAD SCREW
W/LOCKWASHER
LOOSEN TWO #6-32 x 3/8"
PAN HEAD SCREWS
W/LOCKWASHERS
FAN MOTOR
ASSEMBLY
A
L
3.2
Remove One of the Three #6-32 x 3/8” Pan Head
Screw with Lockwasher in the Fan Motor Assembly
and loosen the remaining Two #6-32 x 3/8” Pan Head
Screws with Lockwashers (Figure 2).
Figure 2