Luminance Brands Kathy Ireland Home Highpointe LED CF205LBQ01 User manual

READ AND SAVE THESE INSTRUCTIONS
• Español - página 31
• Français - page 61
MODERN
1-800-777-4440
www.luminancebrands.com
Questions, problems, missing parts: Before returning to the store, Call Customer Service
Net Weight: 22.3 Lbs.
HIGHPOINTE LED
54” Ceiling Fan Owner’s Manual
Model Numbers
CF205LBQ01
CF205LGES01
CF205LGRT01
CF205LORB01
CF205LCVS01
Part No. F40BP75740002 Form No. BP7574-2
Revision: 12082020 U.L. Model No.: CF205L-1

2
U.L. Model No.: CF205L-1
Table of Contents
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician
if in doubt.
4. The longer downrod furnished with the fan
provides the minimum recommended floor to fan
blade clearance for a 9 foot ceiling. The 6” downrod
(supplied) must be used for an 8 foot ceiling.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
READ AND SAVE THESE INSTRUCTIONS
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
UC7067RA, manufactured by Rhine Electric Co., Ltd.
To avoid fire, shock or injury, do not use a
Luminance Brands or any other brand of control not
specifically approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
Section Page
Safety Instructions ................................ 2
1. Unpacking Instructions ..........................3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Ceiling Fan Assembly ..........................5-9
4. How to Hang Your Ceiling Fan ..................10-11
5. How to Wire Your Ceiling Fan ..................12-16
6. Final Assembly .............................17-19
7. Disassemble the LED Light Fixture Assembly for the
No-Light Cover Installation Only .................20-21
Section Page
8. Remote Control Procedures ....................22-24
9. Reverse Switch Operation ....................... 25
10. Accessories ................................. 25
11. Repair Parts ...............................26-27
12. Maintenance ................................. 28
13. Troubleshooting .............................. 28
Ceiling Fan Limited Warranty ....................... 29
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
French ........................................ 61
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

1. Unpacking Instructions
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
1.1
Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: The loose parts are individually packaged
for ease of installation. Place the parts from the
loose parts bags in a small container to keep them
from being lost. If any parts are missing, contact
your local retailer or catalog outlet for replacement
before proceeding.
1.2
Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper foam
pad with the bottom of the motor facing up.
The upper foam pad serves as a holder for the fan during
the first stages of assembly.
R
A
D
E
F
H
I
J
G
BC
Q
M
L
K
N
O
P
0
P
Q
PACKAGE CONTENTS
1
5
2
3
4
6
7
11
8
10
9
Part Description Quantity
A Fan Motor/Housing Assembly 1
B Ceiling Cover 1
C Coupler Cover 1
D Fan Blades 3
E Fan Blades Flanges 3
F Decorative Blade Nuts (bagged) 9
G Hanger Bracket 1
H Lower Housing 1
I Glass 1
J No-Light Cover 1
K Hanger Ball/12” Downrod Assembly 1
L 6” Downrod 1
M Decorative Rod Assembly 3
N Rod Support Assembly 1
O LED Light Fixture Assembly 1
P Remote Control Transmitter, SR401 1
Q Remote Control Receiver 1
HARDWARE CONTENTS
Part Description Qty.
1 Threaded Studs, #8-32 x 1-1/4” 2
2 Knurled Knobs, #8-32 2
3 Lockwashers, External Tooth, #8 2
4 Clevis Pin 1
5 Hairpin Clip 1
6 Wire Connectors 3
7 #8-32 x 7/16” Oval Head Screws w/Lockwashers 10
8 #8-32 x 3/8” Pan Head Screw
(LED light fixture assembly screws - spare) 1
9 1/4-20 x 11mm Oval Head Screws w/Lockwashers 7
10 #8-32 x 3/8” Pan Head Screw
(lower housing screw - spare) 1
11 Blade Balance Kit 1

4
U.L. Model No.: CF205L-1
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 12).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One Wire Stripper One Wire Cutter
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Your Ceiling Fan comes supplied with a Fan/Light
Remote Control which consists of a receiver mounted
inside the ceiling cover of the fan motor housing. This
system allows you to regulate your ceiling fan speed
and light ON/OFF.
2. Electrical Requirements
Your new Ceiling Fan will require a grounded electrical
supply line of 120 Volts AC, 60 Hz, 15 Amp circuit.
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are
not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
If your fan is to replace an existing ceiling light fixture,
turn electricity OFF at the main fuse box at this time and
remove the existing light fixture.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
1. Unpacking Instructions (Continued)
Controls (Sold Separately)
SW406 Wall Control (sold separately) may be used
with this 54” Highpointe LED Ceiling Fan. Controls are
recommended for indoor use only.

5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
3. Ceiling Fan Assembly
FAN BLADE
DECORATIVE
BLADE NUTS
(3 per blade/flange)
BLADE FLANGE
#8-32 x 7/16" OVAL HEAD
SCREWS WITH LOCKWASHERS
(3 per blade/flange)
Figure 1
3.1
Mount the Fan Blades to the Blade Flanges using three
#8-32 x 7/16” Oval Head Screws with Lockwashers and
Three Decorative Blade Nuts (supplied) (Figure 1).
1/4-20 x 11mm OVAL HEAD
SCREWS WITH LOCKWASHERS
(2 per flange)
BLADE FLANGE
MOTOR HUB
Figure 2
3.2
Remove and discard the Three Shipping Retainers securing
the Motor Hub in the Fan Motor/Housing Assembly.
NOTE: Take care not to scratch the Fan Motor/
Housing Assembly when installing the blade
assemblies.
Position the Blade Flange Assembly on the Fan Motor/
Housing Assembly.
Install and securely tighten the 1/4-20 x 11mm Oval
Head Screws with Lockwashers (two per blade
assembly, supplied) into the Blade Flange Assembly.
Interlock the Blade Flange Assemblies as you rotate the
Motor Hub (Figure 2).
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
LOWER
HOUSING
FAN MOTOR/
HOUSING
ASSEMBLY
#8-32 x 3/8" PAN HEAD SCREW
WITH LOCKWASHER
KEYHOLE
SLOTS (2)
#8-32 x 3/8" PAN HEAD SCREW
Figure 3
3.3
Remove One of the Fan Motor/Housing Assembly
#8-32 x 3/8” Pan Head Screws (retain for later use).
Loosen the remaining Two Screws.
Position the Lower Housing on the Fan Motor/Housing
Assembly, aligning the Keyhole Slots over the Fan Motor
Screws. Rotate the Lower Housing clockwise to engage
the Two loosened #8-32 x 3/8” Pan Head Screws into
the Keyhole Slots.
Reinstall the previous removed Screw. Tighten the
Three Screws to secure the Lower Housing to the Fan
Motor/Housing Assembly (Figure 3).
A spare #8-32 x 3/8” Pan Head Screw supplied in parts
bag, if needed.

6
U.L. Model No.: CF205L-1
3. Ceiling Fan Assembly (Continued)
DOWNROD
THREE 80" MOTOR
WIRES (UNTWISTED)
Figure 5
3.5
Turn the partially assembled Ceiling Fan over and position
it on the lower foam pad. The Lower Housing should be
resting on the pad so that the top of the motor faces up.
3.6
Separate, untwist and unkink the Three 80” Motor
Wires.
Route the Three 80” Black, Blue, and White Motor
Wires through the Downrod (Figure 5).
MOTOR
COUPLING
DOWNROD
LOOSEN PHILLIPS
HEAD SET
SCREWS (2)
Figure 6
3.7
Loosen the Two Phillips Head Set Screws in the Motor
Coupler for installation of the Downrod (Figure 6).
Seat the Downrod in the Motor Coupler (Figure 6).
Rotate and align the Downrod holes with all the holes in
the Motor Coupler (Figure 6).
PHILLIPS HEAD SET SCREW (LOOSENED)
HANGER BALL
DOWNROD
PIN
GREEN GROUND WIRE
Figure 4
3.4
Remove the Hanger Ball by loosening the Phillips Head
Set Screw in the Hanger Ball until the Ball falls freely
down the Downrod (Figure 4).
Remove the Pin from the Downrod, then remove the
Hanger Ball (Figure 4).
Retain the Pin and Hanger Ball for reinstallation in
Step 3.13.
NOTE: If you have an eight-foot ceiling, you will
have to use the 6” Downrod (supplied) in order to
maintain the necessary blade-to-floor clearance of
seven feet.
The Three Decorative Rod Assemblies and the
Rod Support Assembly will not be installed on a
6” Downrod.
MOTOR
COUPLER

7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
3. Ceiling Fan Assembly (Continued)
MOTOR
HOUSING
GROMMET
COUPLER
COVER
Figure 8
HAIRPIN
CLIP
CLEVIS
PIN
MOTOR
COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
RETIGHTEN
PHILLIPS HEAD
SET SCREW (2)
Figure 7
COUPLER
COVER
ROD SUPPORT
ASSEMBLY
SCREWS (3)
(Toward Top)
GROMMET
12" DOWNROD
Figure 9
3.9
Make sure the Grommet is properly installed in the
Coupler Cover, then slide the Coupler Cover on the
Downrod until it rests on the Motor Housing (Figure 8).
3.10
NOTE: If you installed the 6” Downrod, the three
Decorative Rod Assemblies and the Rod Support
Assembly will not be installed. Disregard Steps 3.10
through 3.12; proceed to Step 3.13.
Make sure the Grommet is properly installed in the Rod
Support Assembly. Slide the Rod Support Assembly onto
the 12” Downrod (Figure 9).
Then position the three screws in the Rod Support
Assembly toward the top (Figure 9).
3.8
Align the Clevis Pin holes in the Downrod with the holes
in the Motor Coupler.
Install the Clevis Pin and secure with the Hairpin Clip
(Figure 7).
The Clevis Pin must go through the holes in the Motor
Coupler. It is critical that the Clevis Pin in the Motor
Coupler is properly installed and securely tightened.
Retighten the Two Phillips Head Set Screws to secure
the Downrod to the Motor Coupler (Figure 7).
It is critical that the clevis pin and setscrews in the
motor coupler are properly installed and securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
WARNING
!
MOTOR
COUPLER

8
U.L. Model No.: CF205L-1
DECORATIVE
ROD ASSEMBLY
UPPER
DECORATIVE ROD
SCREWS (3)
12" DOWNROD
ROD
SUPPORT
ASSEMBLY
Figure 11
3.12
Remove and Retain the Three Upper Decorative Rod
Screws, located in the Rod Support Assembly.
Slide the Rod Support Assembly up the 12” Downrod
until the threaded holes in the Rod Support align with
the holes in the Decorative Rod Assemblies (Figure 11).
Secure the Decorative Rods to the Rod Support by
reinstalling the Three Decorative Rod Screws; do not
tighten the Rod Screws at this time.
Rotate the Rod Support Assembly until the Decorative
Rod Assemblies are aligned vertically with the
12” Downrod (Figure 11).
Hold the Rod Support in this position while tightening all
Six Decorative Rod Screws securely.
DECORATIVE
ROD ASSEMBLY
LOWER
DECORATIVE ROD
SCREWS (3)
12" DOWNROD
MOTOR
HOUSING
Figure 10
3.11
Remove and Retain the Three Lower Decorative Rod
Screws, located in the Motor Housing.
Position the Three Decorative Rod Assemblies onto the
Motor Housing (Figure 10).
The Decorative Rods must be oriented so that they
lean in towards the 12” Downrod.
Reinstall the Three Lower Decorative Rod Screw.
Do not tighten the Rod Screws at this time.
3. Ceiling Fan Assembly (Continued)

9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
DOWNROD
CEILING
COVER
6 TO 9
INCHES
HANGER BALL
WHITE WIRE
BLACK WIRE
1/2-INCH BLUE WIRE
Figure 13
3.14
The Fan comes with Black, Blue and White Wires that
are 80” long.
Measure up approximately 6 to 9-inches above top of
Hanger Ball / Downrod Assembly (Figure 13).
Cut off excess Wires and strip back insulation 1/2-inch
from end of Wires.
You have now completed the initial assembly of your
new Ceiling Fan. You can now proceed with hanging and
wiring your Fan.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
DOWNROD
CEILING
COVER
PIN HANGERBALL
SETSCREW
Figure 12
3.13
Place the Ceiling Cover over the Downrod. Then reinstall
the Hanger Ball (Figure 12) on the Downrod as follows.
Route the Three 80” Motor Wires through the Hanger
Ball and slide the Hanger Ball over the Downrod.
Position the Pin through the Two Holes in the Downrod
and align the Hanger Ball so the Pin is captured in the
Groove in the top of the Hanger Ball.
Pull the Hanger Ball up tight against the Pin and securely
tighten the Set Screw in the Hanger Ball. A loose Set
Screw could create fan wobble.
3. Ceiling Fan Assembly (Continued)

10
U.L. Model No.: CF205L-1
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
4.1
Securely attach the Hanger Bracket to the Outlet Box
using the Two Screws supplied with the Outlet Box
(Figure 15).
Hanger bracket must seat firmly against outlet box.
If the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER BRACKET
ANTI-ROTATION TAB
OUTLET BOX
Figure 15
FLOOR
CEILING
AT LEAST
7'
Figure 14
4. How to Hang Your Ceiling Fan
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor (Figure 14).
CAUTION
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
AT LEAST
7 FT.
(2.1m)

11
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
4. How to Hang Your Ceiling Fan (Continued)
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
HANGER BRACKET
HANGER BALL
HANGER BALL
GROOVE
ANTI-ROTATION
TAB
Figure 16
4.2
Carefully lift the Fan and seat the Hanger Ball/
Downrod Assembly on the Hanger Bracket that was
just attached to the Outlet Box (Figure 16).
Be sure the Groove in the Ball is engaged with the
Anti-Rotation Tab on the Hanger Bracket (Figure 16).
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to
FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

12
U.L. Model No.: CF205L-1
To avoid possible fire or shock, do not pinch the
antenna wire between the hanger bracket and the
receiver.
WARNING
!
FOR LIGHT
TO MOTOR N
AC IN N
TO MOTOR L
RECEIVER ANTENNA WIRE
AC IN L
RECEIVER
Figure 17
5.2
Locate the Electronic Receiver and insert its Antenna
Wire into the opening of the Hanger Bracket above
the Hanger Ball. Continue to insert the body of the
Receiver (flat side facing up) into the opening, orient as
shown. Be careful not to pinch any Wires between the
Receiver body and the Bracket or Ball (Figure 17).
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
5.1
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or receiver.
Disconnect electrical power to the branch circuit at the
circuit breaker or fuse box before attempting to wire the
ceiling fan.
5. How to Wire Your Ceiling Fan
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!

13
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
5. How to Wire Your Ceiling Fan (Continued)
FOR LIGHT
TO MOTOR L
AC IN L
TO MOTOR N
AC IN N
HANGER BALL, HANGER BRACKET,
& SUPPLY GREEN GROUND WIRES
WIRE
CONNECTOR
Figure 18
FOR LIGHT
TO MOTOR L
AC IN L
AC IN N
TO MOTOR N
WIRE
CONNECTOR
SUPPLY AND RECEIVER
WHITE WIRES
Figure 19
5.3
NOTE: Make all wiring connections using the wire
connectors supplied in the hardware kit and remote
control kit. Make sure that all connections are tight,
including ground, and that no bare wire is visible at
the wire connectors, except for the supply circuit
ground wire.
Connect the Green Ground Wire from the Hanger Ball
and the Green Ground Wire from the Hanger Bracket
to the Ground Conductor of Supply (this may be a bare
wire or wire with Green Colored insulation). Securely
connect Wires with Wire Connectors (supplied in parts
bag) (Figure 18).
5.4
Securely connect the Receiver White Wire (AC IN N) to
the Supply White Wire (neutral) using the Wire Connector
(supplied in parts bag) (Figure 19).

14
U.L. Model No.: CF205L-1
5. How to Wire Your Ceiling Fan (Continued)
FOR LIGHT
TO MOTOR L
TO MOTOR N
AC IN N
AC IN L
WIRE
CONNECTOR
SUPPLY AND
RECEIVER
BLACK WIRES
Figure 20
TO MOTOR L
TO MOTOR N
AC IN N
AC IN L
FOR LIGHT
FAN AND
RECEIVER
WHITE WIRES
WIRE
CONNECTOR
Figure 21
5.5
Securely connect the Receiver Black Wire (AC IN L) to
the Supply Black Wire (hot) using the Wire Connector
(supplied in parts bag) (Figure 20).
5.6
Securely connect the Receiver White Wire
(TO MOTOR N) to the Fan Motor White Wire using
the Wire Connector (supplied in parts bag) (Figure 21).

15
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
5. How to Wire Your Ceiling Fan (Continued)
5.7
Securely connect the Receiver Black Wire
(TO MOTOR L) to the Fan Motor Black Wire using the
Wire Connector (supplied in parts bag) (Figure 22).
5.8
Securely connect the Receiver Blue Wire (TO LIGHT)
to the Fan Motor Blue Wire using the Wire Connector
(supplied in parts bag) (Figure 23).
NOTE: Failure to properly connect the Receiver
Wires will damage the device and render it
non-operable.
TO MOTOR N
AC IN N
AC IN L
FOR LIGHT
TO MOTOR L
SUPPLY AND RECEIVER
BLACK WIRES
WIRE CONNECTOR
Figure 22
TO MOTOR N
AC IN N
AC IN L
TO MOTOR L
FOR LIGHT
WIRE CONNECTOR
SUPPLY AND RECEIVER
BLUE WIRES
Figure 23
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the supply circuit ground
wire. Do not operate fan until blades are in place.
Noise and fan damage could result.
WARNING
!

16
U.L. Model No.: CF205L-1
5. How to Wire Your Ceiling Fan (Continued)
WIRE
CONNECTORS
(Tucked Inside
Outlet Box)
Figure 24
5.9
Position the Antenna Wire on top of the Receiver.
While inserting the Receiver fully into the Hanger Bracket,
turn Wires upward and carefully push Wires into the
Outlet Box, with the White and Green Wires on one side
of the Outlet Box and position the Black and Blue Wires
on the other side of the Outlet Box (Figure 24).
ANTENNA
RECEIVER
GND
STANDARD ON-OFF WALL
SWITCH OR OPTIONAL
SW406 WALL CONTROL BLACK
BLACK
WHITE
BLACK or RED
BLACK
WHITE
HANGER BALL
GREEN WIRE (GROUND) FROM
HANGER BALL AND HANGER
BRACKET
TWO-CONDUCTOR
CABLE
(WITH GROUND)
BLACK
(HOT)
WHITE
GROUND
TO
120-VOLT
SUPPLY
WHITE
BLUE
WHITE
BLUE
Figure 25
5.10
Wiring Schematic for reference (Figure 25).

17
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
6.1
Engage the Fan Motor Blue Wire Connector into the
LED Light Fixture Assembly Black Wire Connector
(Figure 26).
Engage the Fan Motor White Wire Connector into the
LED Light Fixture Assembly White Wire Connector
(Figure 26).
The connections are complete when you hear a soft
click.
6. Final Assembly
LED LIGHT FIXTURE
ASSEMBLY
WHITE WIRE CONNECTOR
FAN MOTOR
WHITE WIRE CONNECTOR
LED LIGHT FIXTURE
ASSEMBLY
LED LIGHT FIXTURE
ASSEMBLY
BLACK WIRE CONNECTOR
FAN MOTOR
BLUE WIRE CONNECTOR
Figure 26
#8-32 x 1/4" PAN HEAD SCREWS
WITH LOCKWASHERS (3)
LED LIGHT FIXTURE
ASSEMBLY LOWER HOUSING
#8-32 x 3/8" PAN HEAD
SCREWS (3)
Figure 27
6.2
Remove and Retain the Three #8-32 x 3/8” Pan Head
Screws from the Lower Housing.
Carefully tuck all the Wires and Connectors into the
Lower Housing.
Position the LED Light Fixture Assembly onto the Lower
Housing, aligning the Three Holes.
NOTE: Verify that the wires and connectors are not
trapped between the LED Light Fixture Assembly
and the Lower Housing.
Reinstall and tighten the Three #8-32 x 3/8” Pan Head
Screws to complete the assembly of the LED Light
Fixture Assembly (Figure 27).
A spare #8-32 x 3/8” Pan Head Screw supplied in parts
bag, if needed.
To avoid possible fire or shock, do not pinch wires
between the Lower Housing and the LED Light Fixture
Assembly.
WARNING
!

18
U.L. Model No.: CF205L-1
6. Final Assembly (Continued)
THREADED STUDS (2)
HANGER BRACKET
Figure 29
6.4
Screw the 1-1/4” Threaded Studs into the Threaded Holes
on the bottom of the Hanger Bracket with your fingers
(Figure 29).
6.3
Place the Glass into the opening of the Lower Housing,
aligning the three Flat Areas on the top edge of the Glass
with the three raised Dimples on the Lower Housing and
turn the Glass clockwise until it stops (Figure 28).
NOTE: Periodically check that the Glass is seated
fully clockwise in the Lower Housing.
GLASS
LOWER
HOUSING
DIMPLES (3)
FLAT
AREA
Figure 28

19
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF205L-1
6. Final Assembly (Continued)
6.5
Lift the Ceiling Cover up to the Threaded Studs and turn
until Studs protrude through the Holes in the Ceiling Cover
(Figure 30).
Secure the Ceiling Cover in place by sliding Lockwashers
over the Threaded Studs and installing the two Knurled
Knobs (supplied in parts bag). (Figure 30).
Tighten the Knurled Knobs securely until the Ceiling
Cover fits snugly against the ceiling and the hole in the
Ceiling Cover is clear of the Downrod.
THREADED
STUD (2)
CEILING
COVER
KNURLED
KNOB (2)
LOCKWASHER (2)
Figure 30
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
WARNING
!
To avoid possible fire or shock, make sure that
antenna wire is not pinched between the ceiling cover
and the ceiling.
WARNING
!

7. Disassemble the LED Light Fixture Assembly
for the No-Light Cover Installation Only
20
U.L. Model No.: CF205L-1
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
7.1
Remove and retain the Glass from the opening of the
Lower Housing by turning the Glass counter-clockwise
(Figure 31).
NOTE: Store the Glass in a safe place for future use,
if needed.
GLASS
LOWER
HOUSING
Figure 31
#8-32 x 1/4" PAN HEAD SCREWS
WITH LOCKWASHERS (3)
LED LIGHT FIXTURE
ASSEMBLY LOWER HOUSING
#8-32 x 3/8" PAN HEAD
SCREWS (3)
Figure 32
7.2
Remove and retain the three #8-32 x 3/8” Pan Head
Screws from the Lower Housing to detach the LED Light
Fixture Assembly (Figure 32).
NOTE: Store the #8-32 x 3/8” Pan Head Screws in a
safe place for future use, if needed.