Luminance Brands kathy ireland HOME VERANDA User manual

Part No. F40BP75490002 Form No. BP7549-2
Revision: 02232021 U.L. Model No.: CF542 & CF552
• Español - página 25
• Français - page 49
VERANDA
Wet Location Ceiling Fan Owner’s Manual
Net Weight: 21.6 Lbs.Net Weight: 17.6 Lbs.
CF552GES00 - Golden Espresso
CF552GRT00 - Graphite
CF552ORB00 - Oil Rubbed Bronze
CF552SW00 - Satin White
CF552VS00 - Vintage Steel
52” Model Numbers
CF542ORB00 - Oil Rubbed Bronze
CF542SW00 - Satin White
42” Model Numbers
READ AND SAVE THESE INSTRUCTIONS
INDOOR/OUTDOOR
1-800-777-4440
www.luminancebrands.com
Questions, problems, missing parts: Before returning to the store, Call Customer Service

2
U.L. Model No.: CF542 & CF552
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Table of Contents
Section Page
Safety Instructions ...................................... 2
1. Unpacking Instructions ................................3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Ceiling Fan Assembly ...............................5-12
4. How to Hang Your Ceiling Fan .......................13-14
5. How to Wire Your Ceiling Fan ........................15-16
6. Final Assembly .......................................17
7. Using Your Ceiling Fan .................................18
Section Page
8. Maintenance ........................................ 19
9. Accessories ........................................ 19
10. Energy Efficient Use of Ceiling Fans .................... 19
11. Repair Parts .....................................20-21
12. Troubleshooting .................................... 22
Ceiling Fan Limited Warranty ............................. 23
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
French .............................................. 49
Safety Instructions
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring, and do not operate fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This product is suitable for use in wet locations
when installed in a GFCI protection branch circuit.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All set screws must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
READ AND SAVE THESE INSTRUCTIONS
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To avoid fire, shock or injury, do not use a Luminance
Brands or any other brand of control not specifically
approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
A
C
D
H
I
G
B
E
F
1. Unpacking Instructions
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free for replacement parts:
1-800-777-4440
WARNING
!
1.1
Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration below.
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, call 1-800-777-4440
for replacement parts before proceeding.
1.2
Remove the fan motor assembly from the protective
plastic bag. Place the fan assembly into the upper
styrofoam with the bottom of the motor facing up.
The upper styrofoam serves as a holder for the fan
during the first stages of assembly.
PACKAGE CONTENTS
8
12
11
10
9
1
5
4
6
111
3
27
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Cover 1
C Motor Coupler Cover 1
D Switch Housing Assembly Bracket 1
E Switch Housing Assembly 1
F Hanger Bracket 1
G Hanger Ball / 4.5” Downrod Assembly 1
H Flange Sets 5
I Blade Sets 5
HARDWARE BAG CONTENTS
Part Description Quantity
1 Threaded Studs, #8-32 x 1-1/4” 2
2 Lockwashers, External Tooth #8 2
3 Knurled Knobs, #8-32 2
4 Clevis Pin 1
5 Hairpin Clip 1
6 Wire Connectors 3
7 M5 x 6mm Washer Head Blade Screws 16
8 M4 x 12mm Flat Head Screw (spare) 1
9 M6 x 14mm Pan Head Screw
with Lockwasher (spare) 1
10 M4 x 10mm Serrated Pan Head
Screw (spare) 1
11 Die-Cast Pendant and Coupler (1 set) 1
12 Blade Balance Kit 1

4
U.L. Model No.: CF542 & CF552
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 15).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One Wire Stripper
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
1. Unpacking Instructions (Continued)
THIS FAN IS SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS.
USE ONLY WITH LIGHT KITS MARKED SUITABLE FOR USE IN WET LOCATIONS.
2. Electrical Requirements
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Your New Ceiling Fan will require a Grounded Electrical
Supply Line of 120 volts AC, 60 Hz, 15 amp circuit.
The Outlet Box must be securely anchored and capable
of withstanding a load of at least 50 Pounds.
If your Fan is to replace an Existing Ceiling Light
Fixture, turn Electricity Off at the Main Fuse Box or
Circuit Breaker Panel at this time and remove the
Existing Light Fixture.
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
Controls (Sold Separately)
SR400 Remote Control and SW405 Wall Control (both
sold separately) may be used with this VERANDA
Ceiling Fan.

5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly
REMOVE AND DISCARD THE FIVE
SHIPPING RETAINERS AND SCREWS
FROM THE MOTOR HUB
Figure 1
3.1
Unscrew and Discard the Five Screws and Five
Shipping Retainers from the Motor Hub (Figure 1).
FLANGES (5)
M5 x 6mm WASHER
HEAD BLADE SCREW
(3 per blade/flange)
FAN BLADES (5)
Figure 2
BLADE/FLANGE
ASSEMBLY
M6 x 14mm CAPTIVE
PAN HEAD SCREW
(2 per blade/flange assembly)
Figure 3
3.2
Mount Flanges to Fan Blades using Three M5 x 6mm
Washer Head Blade Screws (supplied in parts bag)
(Figure 2).
3.3
NOTE: Take care not to scratch fan housing when
installing blades.
Loosely attach one Blade/Flange Assembly to the Motor
Hub by securing the Two M6 x 14mm Captive Pan
Head Screws. Make sure the Screws are NOT tightened
(Figure 3).
Repeat this procedure for other Four Blade Assemblies.
To reduce the risk of personal injury, do not bend the
flange when installing the blades, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
WARNING
!

6
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly
BLADE/FLANGE
ASSEMBLY
FLANGE
INTERLOCKING
FEATURE
FLANGE
INTERLOCKING
FEATURE
3.4
The Flanges have an Interlocking feature that must be
fully engaged before tightening the M6 x 14mm Captive
Pan Head Screws (Figure 4).
If one of the Flanges does not seat properly on the
Motor Hub, loosen the adjacent M6 x 14mm Captive
Pan Head Screw, re-engage and reseat the Flanges,
then tighten the M6 x 14mm Captive Pan Head Screw
again.
A spare M6 x 14mm Pan Head Screw is provided in the
parts bag, if needed.
REMOVE & RETAIN ONE
M4 x 10mm SERRATED PAN
HEAD SCREW
LOOSEN TWO
M4 x 10mm
SERRATED
PAN HEAD
SCREWS
Figure 5
3.5
Remove and Retain One of the Three M4 x 10mm
Serrated Pan Head Screws from the Adapter Plate
(Figure 5).
Loosen the Two M4 x 10mm Serrated Pan Head
Screws, three or four turns.
Figure 4

7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly (continued)
ROTATE SWITCH HOUSING ASSEMBLY
BRACKET CLOCKWISE TO ENGAGE
TWO KEYHOLE SCREWS
REINSTALL & TIGHTEN ONE
M4 x 10mm SERRATED PAN
HEAD SCREW
TIGHTEN TWO
M4 x 10mm
SERRATED
PAN HEAD
SCREWS
SWITCH HOUSING
ASSEMBLY BRACKET
Figure 6
3.6
Position the Switch Housing Assembly Bracket on the
Adapter Plate so that the Two Screws mate with the
Two Switch Housing Assembly Bracket Keyhole Slots
with Rubber Cover.
Turn the Switch Housing Assembly Bracket Clockwise
and tighten both M4 x 10mm Serrated Pan Head
Screws (Figure 6).
Reinstall the previously removed M4 x 10mm Serrated
Pan Head Screw in the remaining Switch Housing
Assembly Bracket Hole.
A spare M4 x 10mm Serrated Pan Head Screw is
provided in parts bag, if needed.
SWITCH HOUSING
ASSEMBLY
MOTOR CONNECTOR
SWITCH HOUSING
ASSEMBLY CONNECTOR
BLUE AND WHITE
WIRES AND
CONNECTORS
Figure 7
3.7
Engage the Switch Housing Assembly Connector with
the Motor Connector (Figure 7).
The Two Connectors are Keyed and Color-Coded and
must be mated correctly (color-to-color) before they can
be engaged.
Make sure the Connector Latch closes properly.
If an accessory light kit is not being used, verify that
the wire connectors on the white and blue wire wire in
the switch housing assembly are present and tight.
WARNING
!

8
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly (continued)
REMOVE AND RETAIN
M4 x 12mm FLAT HEAD
SCREWS (3)
SWITCH HOUSING
ASSEMBLY BRACKET
Figure 8
3.8
Remove and retain the Three M4 x 12mm Flat Head
Screws from the Switch Housing Assembly Bracket
(Figure 8).
SWITCH
HOUSING
ASSEMBLY
REINSTALL AND TIGHTEN
M4 x 12mm FLAT HEAD
SCREWS (3)
Figure 9
3.9
Carefully tuck all Wires and Connectors under the
Switch Housing Assembly.
Secure the Switch Housing Assembly by reinstalling
the Three M4 x 12mm Flat Head Screws (previously
removed) (Figure 9).
A spare M4 x 12mm Flat Head Screw is provided in the
part bag, if needed.
To avoid possible fire or shock, do not pinch wires
between the switch housing assembly and the switch
housing assembly bracket.
WARNING
!

9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly (continued)
STYROFOAM
PARTIALLY ASSEMBLED
CEILING FAN
Figure 10
3.10
Carefully turn and place the partially assembled Ceiling
Fan right side up, on the styrofoam being careful not to
bend the Ceiling Fan Blades (Figure 10).
3.11
Remove the Hanger Ball from the 4.5” Downrod by
loosening the Set Screw in the Hanger Ball until the Ball
falls freely down the Downrod (Figure 11).
Remove the Pin from the Downrod, then remove the
Hanger Ball.
Retain the Pin and Hanger Ball for reinstallation in
Step 3.18.
NOTE: Do not loosen the screw holding the green
ground wire. PHILLIPS HEAD SET SCREW (LOOSENED)
HANGER BALL
4.5" DOWNROD
PIN
GREEN GROUND WIRE
Figure 11
THREE 80" MOTOR LEADS (UNTWISTED)
4.5" DOWNROD
Figure 12
3.12
Separate, untwist and unkink the Three 80” Motor
Wires.
Route the 80” Black and White Motor Wires through the
4.5” Downrod (Figure 12).
THREE 80” MOTOR WIRES (UNTWISTED)

10
U.L. Model No.: CF542 & CF552
3. Ceiling Fan Assembly (continued)
MOTOR
COUPLER
LOOSEN SET
SCREWS (2)
DOWNROD
Figure 13
3.13
Loosen the Two Phillips Head Set Screws in the Motor
Coupler for installation of the 4.5” Downrod (Figure 13).
Seat the 4.5” Downrod in the Motor Coupler
(Figure 13).
Rotate and align the 4.5” Downrod holes with the Two
Holes in the Motor Coupler (Figure 13).
CLEVIS PIN
HAIRPIN
CLIP
HAIRPIN
CLIP
CLEVIS
PIN
MOTOR COUPLER
Figure 14
3.14
Install the Clevis Pin and secure with the Hairpin Clip
(Figure 14).
The Clevis Pin must go through the Motor Coupler
Holes. It is critical that the Clevis Pin in the Motor
Coupler is properly installed and securely tightened.
It is critical that the clevis pin in the motor coupler is
properly installed. Failure to verify that the clevis pin is
properly installed could result in the fan falling.
WARNING
!

11
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
RETIGHTEN TWO
PHILLIPS HEAD
SET SCREWS
MOTOR
COUPLER
3.15
While pulling up on the 4.5” Downrod, retighten the Two
Set Screws (previously loosened) in the Motor Coupler
to secure the Downrod into place (Figure 15).
NOTE: The set screws must be properly installed as
described above, or fan wobble could result.
Figure 15
3. Ceiling Fan Assembly (continued)
GROMMET
DOWNROD
COUPLER
COVER
Figure 16
3.16
Make sure the Grommet is properly installed in the
Motor Coupler Cover then slide the Motor Coupler
Cover on the Downrod until it rests on the Motor
Housing.
Be sure the Motor Coupler Cover is oriented correctly
(Figure 16).
CEILING
COVER
DOWNROD
Figure 17
3.17
Place the Ceiling Cover over the Downrod.
Be sure the Ceiling Cover is oriented correctly
(Figure 17).
It is critical that the set screws in the motor coupler are
properly installed and securely tightened. Failure to
verify that the set screws are properly installed could
result in the fan falling.
WARNING
!

CEILING
COVER
HANGER BALL
HANGER BALL PIN
HANGER BALL
GROOVE
DOWNROD
SET SCREW
Figure 18
3.18
Route the Three 80” Motor Wires through the Hanger
Ball.
Reinstall the Hanger Ball (Figure 18) on the Downrod
as follows:
Position the Hanger Ball Pin through the two Holes in
the Downrod and align the Ball so the Pin is captured in
the Groove in the top of the Hanger Ball.
Pull the Hanger Ball up tight against the Pin and
securely tighten the Set Screw in the Hanger Ball.
NOTE: A loose set screw could create fan wobble.
It is critical that the pin in the hanger ball is properly
installed and the set screw securely tightened. Failure
to verify that the pin and set screw are properly
installed could result in the fan falling.
WARNING
!
3. Ceiling Fan Assembly (continued)
BLACK WIRE
6 TO 9
INCHES
BLUE WIRE
WHITE WIRE
HANGER BALL
1/2
INCH
3.19
The Fan comes with Black, Blue and White Wires that
are 80-inches long.
Before installing the Fan, measure up approximately
6 to 9-inches above top of Hanger Ball/Downrod
Assembly (Figure 19).
Cut off excess Wires and strip back insulation 1/2-inch
from end of Wires.
12
U.L. Model No.: CF542 & CF552
Figure 19

13
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
FLOOR
AT LEAST
7'
CEILING
Figure 20
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
4.1
Securely attach the Hanger Bracket to the Outlet
Box using the Two Screws supplied with the Outlet Box
(Figure 21).
Hanger bracket must seat firmly against outlet box.
If the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
HANGER
BRACKET
ANTI-ROTATION
TAB
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
4. How to Hang Your Ceiling Fan
Figure 21
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor (Figure 20).
CAUTION
!

To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
Failure to seat anti-rotation tab in groove could cause
damage to electrical wires and possible shock or fire
hazard.
WARNING
!
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
HANGER BRACKET
HANGER BALL
HANGER BALL
GROOVE
ANTI-ROTATION TAB
Figure 22
4. How to Hang Your Ceiling Fan (continued)
4.2
Carefully lift the Fan and seat the Hanger Ball/
Downrod Assembly into the Hanger Bracket that was
just attached to the Outlet Box (Figure 22).
Be sure the Groove in the Ball is lined up with
Anti-Rotation Tab on the Hanger Bracket (Figure 22).
14
U.L. Model No.: CF542 & CF552

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
15
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
5. How to Wire Your Ceiling Fan
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box or circuit breaker
panel before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
!
LISTED WIRE
CONNECTOR
SUPPLY WHITE
(NEUTRAL)
FAN MOTOR
WHITE WIRE
Figure 24
5.2
NOTE: If you are using an Luminance Brands Light
Fixture with your Fan, see Light Fixture Owner’s
Manual for wiring.
Securely connect the Fan Motor White Wire to the
Supply White (neutral Wire using Wire Connector
(supplied) (Figure 24).
GROUND
CONDUCTOR SUPPLY
LISTED WIRE
CONNECTOR
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
GREEN WIRE
(GROUND) FROM
HANGER BALL
Figure 23
5.1
Connect the Green Ground Wire from the Hanger Ball
and the Green Ground Wire from the Hanger Bracket
to the Ground Conductor of Supply (this may be a bare
wire or wire with green colored insulation). Securely
connect Wires with Wire Connectors (supplied)
(Figure 23).
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan or
receiver.
CAUTION
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!

16
U.L. Model No.: CF542 & CF552
5. How to Wire Your Ceiling Fan (Continued)
FAN MOTOR
BLACK WIRE
SUPPLY BLACK
(HOT)
LISTED WIRE
CONNECTOR
FAN MOTOR BLUE WIRE
Figure 25
5.3
Securely connect the Fan Motor Black Wire and
Blue Wire to the Supply Black (hot) Wire using Wire
Connector (supplied) (Figure 25).
BLACK/BLACK/
BLUE WIRES
WHITE WIRES
GREEN
WIRES
Figure 26
5.4
After Connections have been made, turn Wires upward
and carefully push Wires into the Outlet Box, with the
White and Green Wires on one side of the Outlet Box
and position the Black/Black/Blue Wires on the other
side of the Outlet Box (Figure 26).
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!

6.2
Lift the Ceiling Cover up to the Threaded Studs and
turn until Studs protrude through the Holes in the
Ceiling Cover (Figure 28).
6.3
Secure the Ceiling Cover in place by sliding
Lockwashers over the Threaded Studs and installing
the Two Knurled Knobs (supplied) (Figure 28).
Tighten the Knurled Knobs securely until the Ceiling
Cover fits snugly against the Ceiling and the Hole in the
Ceiling Cover is clear of the Downrod.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
17
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
6. Final Assembly
THREADED
STUDS (2)
KNURLED KNOBS (2)
CEILING
COVER
LOCKWASHERS (2)
Figure 28
NOTE: SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY.
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
WARNING
!
6.1
Screw the Two Threaded Studs (supplied) into the
Tapped Holes in the Hanger Bracket (Figure 27).
THREADED
STUDS (2)
Figure 27

18
U.L. Model No.: CF542 & CF552
7.1
Restore Electrical Power to the Outlet Box by turning
the Electricity on at the Main Fuse Box or Circuit
Breaker Panel.
During Summer Months, run the Fan Counter-
Clockwise, as you look up at it, to direct airflow
downward.
During the Winter Months, run the Fan Clockwise, as
you look up at it, to direct airflow upward.
If airflow is desired in the opposite direction, turn the
Ceiling Fan off and wait for the Blades to stop turning.
Slide the Reverse Switch (located on the side of the
Switch Housing Assembly) to the opposite position, and
turn the Ceiling Fan on again (Figure 29).
The Fan Blades will turn in the opposite direction and
reverse the airflow.
Reverse Switch Information
Season Rotation Direction
Summer Counter-Clockwise
Winter Clockwise
7. Using Your Ceiling Fan
REVERSE
SWITCH SWITCH HOUSING
ASSEMBLY
Figure 29
7.2
Check the operation of the fan by gently pulling on the
pull chain switch.
Cut the 3-speed switch pull chain to a desired length
(optional). Connect the die-cast pendant (supplied)
to the 3-speed switch pull chain by sliding the die-
cast pendant (small hole first) onto the pull chain
(Figure 30). Attach the chain coupler to the end of the
chain and allow the die-cast pendant to fall down over
the couplers.
Your fan model is equipped with a 4-position,
3-speed pull chain switch (Figure 30). The operating
sequence is as follows:
Three-Speed
1st Pull — HIGH
2nd Pull — MEDIUM
3rd Pull — LOW
4th Pull — OFF
SWITCH HOUSING
ASSEMBLY
CHAIN COUPLER
3-SPEED SWITCH
PULL CHAIN
DIE-CAST PENDANT
Figure 30

19
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF542 & CF552
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
See your local Luminance Brands dealer,
www.luminancebrands.com or our catalog for these
accessories:
· Ceiling Fan Light Kits
· Ceiling Fan/Light Controls
· Downrod Extension Kits
9. Accessories
10. Energy Efficient Use of Ceiling Fans
The use of any other control not specifically approved
for this fan could result in fire, shock and personal
injury.
WARNING
!
Do not use water when cleaning your ceiling fan.
It could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
8. Maintenance
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure quality and
product performance.
Choosing the Appropriate Mounting Location.
Ceiling fans should be installed, or mounted, in the
middle of the room and at least 7 feet above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Luminance Brands Retailer for
optional mounting accessories.
Using the Ceiling Fan Year Round. In the summer,
use the ceiling fan in the counter-clockwise direction.
The airflow produced by the ceiling fan creates a
wind-chill effect, making you “feel” cooler. Select a
fan speed that provides a comfortable breeze, lower
speeds consume less energy. In the winter, reverse
the motor and operate the ceiling fan at low speed in
the clockwise direction. This produces a gentle updraft,
which forces warm air near the ceiling down into the
occupied space. Remember to adjust your thermostat
when using your ceiling fan - additional energy and
dollar savings could be realized with this simple step!
Turn Off When Not in the Room. Ceiling fans cool
people, not rooms. If the room is unoccupied, turn off
the ceiling fan to save energy.

12
1
53
2
9
8
PARTS BAG
11
4
16
14
6
7
8
5
10
7
6
9
12
13
15
10
20
19
21
17
18
11
22
23
13
14
15
20
U.L. Model No.: CF542 & CF552
Before discarding packaging material, be
certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING
INFORMATION:
• PART NUMBER
• NAME OF ITEM
• PART DESCRIPTION
• MODEL NUMBER
The model number of your Fan will be
found on a label attached to the top
housing.
For repair parts, phone [phone].
11. Repair Parts