Luminance Brands Kathy ireland PRO Series User manual

Net Weight: 16.5 Lbs. Net Weight: 19.8 Lbs.
Part No. F40BP72580013 Form No. BP7258-13
Revision: 01122021 U.L. Model No.: 42-ANT & 52-ANT
CF710BS03
Brushed Steel
CF710ORB03
Oil Rubbed Bronze
CF710WW03
Appliance White
42” PRO Series II LED
Model Numbers
CF711AB03
Antique Brass
CF711BS03
Brushed Steel
50” PRO Series II LED
Model Numbers
CF711ORB03
Oil Rubbed Bronze
CF711WW03
Appliance White
• Español - página 25
READ AND SAVE THESE INSTRUCTIONS
PRO SERIES
www.luminancebrands.com
PRO SERIES II LED
Ceiling Fan Owner’s Manual
1-800-777-4440
Questions, problems, missing parts: Before returning to the store, Call Customer Service
CF711 shown

2
U.L. Model No.: 42-ANT & 52-ANT
Table of Contents
Section Page
Safety Instructions ................................ 2
1. Unpacking Instructions ..........................3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Installing the Hanger Ball/Downrod Assembly . . . . . . . .5-7
4. Installing the Ceiling Cover on the Fan Motor Housing .8-9
5. How to Hang Your Ceiling Fan .................10-11
6. Hanging the Ceiling Fan (Standard) ............... 11
7. Hanging the Ceiling Fan (Close-to-Ceiling) .......... 12
8. How to Wire Your Ceiling Fan ...................13-14
9. Installing the Ceiling Cover ....................... 15
10. Installing the Fan Blades ....................... 16
Section Page
11. Installing the Glass Shades and Light Bulbs ........ 17
12. Removal of the Light Fixture . . . . . . . . . . . . . . . . . . . . . 18
13. Maintenance ................................. 18
14. Using Your Ceiling Fan ......................... 19
15. Accessories .................................. 19
16. Repair Parts ...............................20-21
17. Troubleshooting............................... 22
Ceiling Fan Limited Warranty ....................... 23
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: The CF711 fan is suitable for use with solid-state
speed controls.
NOTE: All set screws must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
READ AND SAVE THESE INSTRUCTIONS
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use this product
by Luminance Brands Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury or
property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

1. Unpacking Instructions
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
1.1
Open carton containing the Fan. Remove top half of
styrofoam unit. Remove parts and check to see that you
have received the following parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, call 1-800-777-4440
for replacement parts before proceeding.
12
5
9
3
8
7
6
4
HARDWARE CONTENTS
Part Description Quantity
1 M5 x 6mm Washer Head Blade Screws 16
2 Wire Connectors, 12 ga. 3
3 Phillips Round Head Flange Screw (spare) 1
4 Rubber Gasket 1
5 Wood Pendants 2
6 Couplings 2
7 Clevis Pin 1
8 Hairpin Clip 1
9 Blade Balance Kit 1
H
I
G
F
E
C
B
A
D
PACKAGE CONTENTS
1.2
Remove the Fan Housing Assembly from the protective
plastic bag. Turn the upper styrofoam pad over and
carefully place the Fan Motor Assembly into the recess
in the pad with the Top of the Motor Facing Up.
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Cover 1
C Switch Housing Cover 1
D Flange Set 5
E Blade Set 5
F Hanger Bracket 1
G Hanger Ball / Downrod Assembly 1
H Glass Shades (3 or 4)
I 9-Watt Medium Base LED Bulbs (3 or 4)

4
U.L. Model No.: 42-ANT & 52-ANT
If your Fan is to replace an Existing Ceiling Light
Fixture, turn Electricity OFF at the Main Fuse Box at
this time and remove the Existing Light Fixture.
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 11).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One 1/4” Blade Screwdriver One Wire Stripper
Materials
Wiring Outlet Box and Box Connectors must be of type
required by the Local Code. The Minimum Wire would
be a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
2. Electrical Requirements
Your New Ceiling Fan will require a Grounded Electrical
Supply Line of 120 Volts AC, 60 Hz, 15 Amp Circuit.
The Outlet Box must be securely anchored and capable
of withstanding a load of at least 50 Pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
1. Unpacking Instructions (Continued)
Controls (Sold Separately)
SW46 Wall Control and SW90 Wall Control (both sold
separately) may be used with this PRO Series Ceiling
Fan. Controls are recommended for Indoor Use Only.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.

5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
IMPORTANT
Your ceiling fan is designed to be installed either in the standard manner, or in the
close-to-the-ceiling manner. Using the standard method, the hanger ball/downrod assembly will suspend
the fan several inches below the ceiling cover. Using the close-to-the-ceiling method, the ceiling cover
installs directly on the fan motor housing, thus mounting the fan 3-1/2 inches closer to the ceiling than the
standard method. In no case should the fan blades be lower than seven feet above the floor. Depending
on your desired mounting method, proceed to “INSTALLING HANGER BALL/DOWNROD ASSEMBLY” for
standard mounting, or to “INSTALLING CEILING COVER ON FAN MOTOR HOUSING” for close-to-the-
ceiling mounting.
3. Installing the Hanger Ball/Downrod Assembly
(For Standard Mounting)
MOTOR
WIRES (3)
CEILING
COVER
3.1
Pass the Motor Wires through the Opening in the
Ceiling Cover.
Be sure the Cover is Oriented Correctly (Figure 1).
NOTE: Motor Wires Vary in Length, Depending on
the Model:
CF710 Ceiling Fan: 42” Motor Wires
CF711 Ceiling Fan: 80” Motor Wires
Figure 1
MOTOR
WIRES (3)
HANGER
BALL/3.5"
DOWNROD
ASSEMBLY
Figure 2
3.2
Separate, Untwist and Unkink the Three Motor Wires.
Route the Motor Wires through the Hanger Ball /
Downrod Assembly (Figure 2).

6
U.L. Model No.: 42-ANT & 52-ANT
3. Installing the Hanger Ball/Downrod Assembly
(For Standard Mounting) (Continued)
DOWNROD
CLEVIS
PIN HAIRPIN
CLIP
MOTOR
COUPLER
HAIRPIN
CLIP
CLEVIS
PIN
LOOSEN
SETSCREWS (2)
3.3
Loosen the Two Setscrews in the Motor Coupler.
Place the Hanger Ball/Downrod Assembly into the
Motor Coupler, aligning the Clevis Pin Holes in the
Downrod with the Holes in the Motor Coupler
(Figure 3).
The Clevis Pin must go through the Holes in the Motor
Coupler and the Holes in the Downrod.
Be sure to push the Straight Leg of the Hairpin Clip
through the Hole near the end of the Clevis Pin until
the Curved Portion of the Hairpin Clip snaps around the
Clevis Pin.
The Hairpin Clip must be properly installed to prevent
the Clevis Pin from working loose.
Pull on the Hanger Ball to make sure the Clevis Pin is
properly installed.
Figure 3
MOTOR
COUPLING
HANGER BALL/
DOWNROD
ASSEMBLY
RETIGHTEN
SETSCREW
RETIGHTEN
SETSCREW
Figure 4
3.4
While pulling up on the Hanger Ball, retighten the Two
Setscrews (previously loosened) in the Motor Coupler
to secure the Hanger Ball/Downrod Assembly into
place (Figure 4).
NOTE: The setscrews must be properly installed as
described above, or fan wobble could result.
NOTE: For hanging instructions using
Hanger Ball/Downrod Assembly, See Page 11,
Section 6. Hanging the Ceiling Fan (Standard
Method Using Hanger Ball/Downrod).
It is critical that the setscrews are securely tightened.
Failure to verify that the setscrews are properly
installed could result in the fan falling.
WARNING
!
It is critical that the clevis pin in the motor coupling
is properly installed. Failure to verify that the pin is
properly installed could result in the fan falling.
WARNING
!

7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
3. Installing the Hanger Ball/Downrod Assembly
(For Standard Mounting) (Continued)
HANGER BALL
/
DOWNROD
ASSEMBLY
6 to 9
INCHES
3.5
The Fan comes with Blue, Black and White Wires that
are 42” or 80” Long, depending on the Model.
Measure up Approximately 6 to 9-inches above Top of
Hanger Ball/Downrod Assembly (Figure 5).
Cut off Excess Wires and Strip Back Insulation 1/2-inch
from end of Wires.
Figure 5

4. Installing the Ceiling Cover on the Fan Motor
Housing (For Close-to-the-Ceiling Mounting)
MOTOR
HOUSING
SCREWS (3)
MOTOR
HOUSING
REMOVE SCREWS (3)
4.1
Remove Three Motor Housing Screws (every other
screw as illustrated) from the Top of the Motor Housing
(Figure 6).
Retain the Three Motor Housing Screws for future use.
Figure 6
RUBBER
GASKET
MOTOR
HOUSING
RUBBER GASKET
LARGE HOLES (3)
RUBBER GASKET
SMALL HOLES (3)
INSTALL
RUBBER
GASKET
4.2
Position the Rubber Gasket (supplied in parts bag) on
the Motor Housing.
The Three Small Holes in the Gasket should Center
over the Holes in the Motor Housing where the Three
Screws were previously removed (Figure 7).
The Three Large Holes in the Gasket should Center
over the Three Screws still Installed in the Motor
Housing.
Figure 7
8
U.L. Model No.: 42-ANT & 52-ANT

6 TO 9
INCHES
MOTOR
COUPLING
MOTOR
COUPLER
4.5
The Fan comes with Blue, Black and White Wires that
are 42” or 80” Long, depending on the Model.
Measure up Approximately 6 to 9-inches above the
Motor Coupler (Figure 10).
Cut off Excess Wires and Strip back Insulation 1/2-inch
from ends of Wires.
Figure 10
4. Installing the Ceiling Cover on the Fan Motor
Housing (For Close-to-the-Ceiling Mounting) (Continued)
DECORATIVE CAP
CEILING COVER
4.3
Gently pry the Decorative Cap from the Ceiling Cover
(Figure 8).
RUBBER GASKET
SCREWS (3)
(Previously Removed)
CEILING COVER
4.4
Align the Holes in the Ceiling Cover with the Holes in
the Motor Housing and Secure using the Three Screws
previously removed in Step 4.1 (Figure 9).
Figure 9
Figure 8
NOTE: For hanging instructions using Close-to-the-
Ceiling Method, See Page 12, Section 7. Hanging
the Ceiling Fan (Close-to-the-Ceiling Method with
Ceiling Cover Installed on the Motor Housing).
9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT

10
U.L. Model No.: 42-ANT & 52-ANT
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor (Figure 11).
CAUTION
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
5. How to Hang Your Ceiling Fan
FLOOR
7'
MIN.
CEILING
Figure 11
HANGER BRACKET
LOOSEN TWO
SCREWS
(SUPPLIED
WITH OUTLET BOX)
OUTLET BOX
SLIDE THE HANGER BRACKET
ONTO THE OUTLET BOX
SCREWS, THROUGH THE
T-SLOT
T-SLOT
5.1
Unscrew (but do not remove) the Two Mounting Screws
in the Outlet Box (Figure 12).
Position the Hanger Bracket on the Outlet Box so that
the T-slots in the Hanger Bracket are aligned with the
Outlet Box Screws.
Figure 12

11
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
5. How to Hang Your Ceiling Fan (Continued)
HANGER BRACKET
HOOK
SECURELY
TIGHTEN
SCREWS
(one on each side)
CEILING
Figure 13
5.2
NOTE: The hanger bracket must be mounted flush
with the ceiling in order for the ceiling cover to
install properly. If necessary, use leveling washers
(not supplied) between the outlet box and the
hanger bracket.
Slide the Hanger Bracket onto the Outlet Box Screws.
Center the Bracket over the Outlet Box and then
securely tighten the Screws (Figure 13).
Hanger bracket must seat firmly against outlet box.
If the outlet box is recessed, use leveling washers
between the hanger bracket and the outlet box until
the bracket is flush with the ceiling. If bracket and/
or outlet box are not securely attached, the fan could
wobble or fall.
WARNING
!
6. Hanging the Ceiling Fan
(Standard Method Using Hanger Ball/Downrod)
HANGER
BRACKET
HOOK
TAB
GROOVE
HANGER BALL
NOTE: CEILING COVER, SUPPLY
WIRES AND FAN WIRES OMITTED
FOR CLARITY.
Figure 14
6.1
Carefully lift the Fan Assembly and seat the Hanger
Ball in the Hanger Bracket (Figure 14).
The Tab on the Hanger Bracket must seat in the
Groove in the Hanger Ball.
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid fire or shock, do not pinch wires between the
hanger ball/downrod assembly and hanger bracket.
WARNING
!

12
U.L. Model No.: 42-ANT & 52-ANT
7. Hanging the Ceiling Fan
(Close-to-the-Ceiling Method with
Ceiling Cover Installed on the Motor Housing)
HANGER
BRACKET
HOOK
HOOK ON HANGER BRACKET MUST PASS THROUGH SCREW HOLE
IN CEILING COVER, INSIDE OF BRACKET TO OUTSIDE OF BRACKET
CEILING
COVER
Figure 15
7.1
Carefully lift the Fan Assembly up to the Hanger
Bracket. Pass the Hook on the Hanger Bracket
(Figure 15) through One of the Screw Holes (not the
slots) in the Ceiling Cover (Figure 15).
The Hook MUST Pass from the Inside of the Ceiling
Cover to the Outside. The Hook will hold the Fan
Assembly while connecting the Wiring.
The hook must pass through the screw hole in the
ceiling cover from the inside to the outside. Any other
hanging method may cause the hook to break and the
fan to fall.
WARNING
!

13
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
8. How to Wire Your Ceiling Fan
The following instructions show that the Hanger Ball/Downrod Assembly and the Close-To-The-Ceiling
Assembly wiring instructions are the same.
GROUND
CONDUCTOR
SUPPLY
LISTED WIRE
CONNECTOR
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET
GREEN WIRE
(GROUND) FROM
HANGER BALL
Figure 16
8.1
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Connect the Hanger Ball Green Ground Wire and
the Green Ground Wire from the Hanger Bracket to
the Ground Conductor of the Supply (this may be
a bare Wire or Wire with green colored insulation)
(Figure 16). Securely connect Wires using Wire
Connectors supplied.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring
must be in accordance with National and Local codes
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
!
Hanger Ball/Downrod Assembly Shown
LISTED WIRE
CONNECTOR
SUPPLY WHITE
(NEUTRAL)
FAN MOTOR
WHITE WIRE
Figure 17
8.2
Securely connect the Fan Motor White Wire to the
Supply White (neutral) Wire using a Wire Connector
supplied (Figure 17).
Hanger Ball/Downrod Assembly Shown
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
NOTE: When wiring the ceiling fan for close-to-the-
ceiling mounting, there will be no green grounding
lead from the hanger ball.

14
U.L. Model No.: 42-ANT & 52-ANT
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until blades are in place. Noise and fan damage
could result.
WARNING
!
8. How to Wire Your Ceiling Fan (Continued)
LISTED WIRE
CONNECTOR
FAN MOTOR
BLACK FAN
WIRE
BLUE
FAN
WIRE
SUPPLY
BLACK
(HOT)
Figure 18
8.3
Securely connect the Fan Motor Black Wire and Blue
Wire to the Supply Black (hot) Wire using a Wire
Connector supplied (Figure 18).
TWO BLACK WIRES
AND ONE BLUE WIRE
WHITE WIRES
GREEN WIRES
Figure 19
8.4
After Connections have been made, turn Wires upward
and carefully push Wires into the Outlet Box, with the
White and Green Wires on one side of the Outlet Box
and Black Wires on the other side of the Outlet Box
(Figure 19).
Hanger Ball/Downrod Assembly Shown
Hanger Ball/Downrod Assembly Shown

15
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
!
9. Installing the Ceiling Cover
REMOVE LEFT
SCREW AND
LOCKWASHER
ON EACH SIDE
LOOSEN THE RIGHT
SCREW/LOCKWASHER
ON EACH SIDE
Figure 20
9.1
Remove the Left Screw and Lockwasher from each
side of the Hanger Bracket (Figure 20) and Loosen the
other Two Screws.
NOTE: When installing the ceiling fan using the
close-to-the-ceiling method, carefully lift the fan
assembly from the hook on the hanger bracket and
proceed as follows.
CLOSE-TO-THE-CEILING ASSEMBLY
REINSALL LEFT
SCREW AND
LOCKWASHER
ON EACH SIDE
HANGER BRACKET
CEILING COVER
HANGER BALL/DOWNROD ASSEMBLY
CEILING COVER
HANGER
BRACKET
REINSALL LEFT
SCREW AND
LOCKWASHER
ON EACH SIDE
Figure 21
9.2
Lift the Ceiling Cover up to the Hanger Bracket.
Engage the Slots in the Ceiling Cover with the
Loosened Screws in the Bracket and turn the Cover
Counterclockwise (Figure 21).
Be sure that the Lockwashers are between the Screw
Heads and the Ceiling Cover.
Install the other Two Screws and Lockwashers; tighten
all Screws securely.
Hanger Ball/Downrod Assembly Shown

16
U.L. Model No.: 42-ANT & 52-ANT
10. Installing the Fan Blades
RUBBER GROMMETS
BLADE FLANGE
ALIGNMENT
POST
M5 x 6 WASHER
HEAD BLADE SCREW (3)
FAN BLADE
Figure 22
10.1
Make sure the Three Rubber Grommets are firmly
seated on each of the Blade Flanges.
Then mount the Blade Flanges to the Fan Blades using
Three M5 x 6 Washer Head Blade Screws per Blade
(Figure 22).
CAPTIVE
SCREW (2)
BLADE
FLANGE
ALIGNMENT
SLOT
MOTOR HUB
Figure 23
10.2
Mount One Blade Assembly to the Motor Hub by
Mating the Alignment Post (Figure 23) of the Flange
with One of the Alignment Slots in the Motor Hub
(Figure 23).
Then tighten the Two Captive Screws in the Flange to
secure the Flange to the Motor Hub.
Repeat this procedure for the other Four Blade
Assemblies. Make sure all Screws are tightened.
Spare Captive Screw provided in Parts Bag, if needed.
CHAIN
COUPLER
WOODEN
PENDANT
3-SPEED
SWITCH
PULL CHAIN LIGHT
FIXTURE
PULL CHAIN
WOODEN
PENDANT
Figure 24
10.3
Cut the Speed Control Switch Pull Chain and the Light
Switch Pull Chain to the desired lengths (optional).
Attach the Coupling/Chain/Wood Pendant Assembly
(supplied) to the Light Fixture Assembly Control Chain
by connecting the Coupling onto the Light Fixture
Assembly Control Chain (Figure 24).
Attach the Coupling/Chain/Wood Pendant Assembly
(supplied) to the Fan Switch Assembly Control Chain
by connecting the Coupling onto the Fan Switch
Assembly Control Chain (Figure 24).
To reduce the risk of personal injury, do not bend the
blade flanges when installing the flanges, balancing
the blades, or cleaning the fan. Do not insert foreign
objects between rotating fan blades.
WARNING
!

17
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
11. Installing the Glass Shades and Light Bulbs
RETAINING
CLIP
SQUEEZE
RETAINING
CLIPS
TOGETHER
AND SLIDE
ON GLASS
SHADE
GLASS
SHADE
9-WATT MEDIUM
BASE LED BULB
(3 or 4)
Figure 25
11.1
To Install the Glass Shade: Squeeze the Retaining
Clips towards the Bulb Socket and Slide on the Glass
Shade (Figure 25). The Spring Clips will Seat the
Shade and Secure it in place.
Install a 9-Watt Medium Base LED Bulb in each of the
Light Fitter Sockets (Figure 25).
To Remove the Shade: First Remove the Light Bulb
from the Socket, then simply Pull the Shade off using a
Twisting Motion.
12. Removal of the Light Fixture
SWITCH
HOUSING
LIGHT
FIXTURE
SCREW (3)
LIGHT BULBS
PREVIOUSLY
REMOVED
Figure 26
12.1
NOTE: In some instances it may be desirable to
install the ceiling fan without the light fixture. If this
is the case, proceed as follows. (You may want to
keep the light fixture for possible future use.)
Light bulbs and glass shades removed.
Remove the Three Switch Housing Screws securing
the Light Fixture (Figure 26).
Retain the Three Switch Housing Screws for Future
Use.
LIGHT
FIXTURE
REMOVE THE TWO
WIRE CONNECTORS
TO DISCONNECT
WIRES FROM LIGHT
FIXTURE AND THE
SWITCH HOUSING
SWITCH
HOUSING
Figure 27
12.2
Disconnect the Two Wire Connectors that are securing
the Light Fixture Wires to the Switch Housing Wires
(Figure 27).
Retain the Wire Connectors for Future Use.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.

18
U.L. Model No.: 42-ANT & 52-ANT
Do not use water when cleaning your ceiling fan.
It could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic Cleaning of your New Ceiling Fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
13. Maintenance
12. Removal of the Light Fixture (Continued)
RECONNECT THE TWO
SWITCH HOUSING WIRES
WITH THE PREVIOUSLY
REMOVED WIRE
CONNECTORS
SWITCH
HOUSING
Figure 28
12.3
Reconnect the Two Switch Housing Wires with the
previously removed Wire Connectors (Figure 28).
SWITCH HOUSING
COVER
SWITCH HOUSING
TUCK WIRES AND
CONNECTORS INSIDE
SWITCH HOUSING
Figure 29
12.4
Tuck the Wires and Connectors inside the Switch
Housing (Figure 29).
SWITCH HOUSING
SWITCH HOUSING
COVER
SCREW (3)
SWITCH HOUSING
COVER PLUG SCREW
Figure 30
12.5
Replace the Switch Housing Cover using the previously
Removed Three Switch Housing Screws (Figure 30).
Place the Switch Housing Cover Plug Screw into the
Bottom of the Switch Housing Cover (Figure 30).
To avoid possible fire or shock, do not pinch wires
between the switch housing and the switch housing
cover.
WARNING
!

19
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: 42-ANT & 52-ANT
14. Using Your Ceiling Fan
REVERSING
SWITCH
REVERSE
SWITCH
14.2
Your Fan Model is equipped with a 4-position,
3-speed Pull Chain Switch (Figure 32). The operating
sequence is as follows:
Three-Speed
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
CHAIN
COUPLER
WOODEN PENDANT
3-SPEED
SWITCH
PULL CHAIN LIGHT
FIXTURE
PULL CHAIN
WOODEN
PENDANT
Figure 32
Figure 31
14.1
Restore Electrical Power to the Outlet Box by turning
the Electricity on at the Main Fuse Box.
During Summer Months, run the Fan Counter-
Clockwise, as you look up at it, to direct airflow
downward.
During the Winter Months, run the Fan Clockwise, as
you look up at it, to direct airflow upward.
If airflow is desired in the opposite direction, turn the
Ceiling Fan OFF and wait for the Blades to stop turning.
Slide the Reverse Switch (located on the side of the
Switch Housing Assembly) to the opposite position, and
turn the Ceiling Fan on again (Figure 36).
The Fan Blades will turn in the opposite direction and
reverse the airflow.
Reverse Switch Information
Season Blade Rotation Direction
Summer Counter-Clockwise
Winter Clockwise
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
See your local Luminance Brands dealer,
www.luminancebrands.com or our catalog for these
accessories:
Ceiling Fan/Light Controls (see store or catalog).
Downrod Extension Kits (see store or catalog).
15. Accessories
The use of any other control not specifically approved
for this fan could result in fire, shock and personal
injury.
WARNING
!

20
U.L. Model No.: 42-ANT & 52-ANT
16. Repair Parts
7
8
10 11
6
15
16
PARTS BAG
9
18
11
10
13
12
14
15
16
17
1
2
3
4
5
14
13
12
13
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER • NAME OF ITEM
• PART DESCRIPTION • MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone [phone].