Luminance Brands Kathy Ireland Home Prima Snugger CF905BS01 User manual

Part No. F40BP74320005 Form No. BP7432-5
Revision: 02112021 U.L. Model No.: CF905-1
PRIMA SNUGGER™
52” Ceiling Fan Owner’s Manual
Model Numbers
Net Weight: 18.3 Lbs.
CF905BS01 - Brushed Steel
CF905ORB01 - Oil Rubbed Bronze
CF905SW01 - Satin White
CF905VNB01 - Venetian Bronze
READ AND SAVE THESE INSTRUCTIONS
TRADITIONAL
M2
M1
L
H
OFF
1-800-777-4440
www.luminancebrands.com
Questions, problems, missing parts: Before returning to the store, Call Customer Service

2
U.L. Model No.: CF905-1
Table of Contents
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
SW46 / U.L. Model No. UC9020, manufactured by Rhine
Electric Co., Ltd.
To avoid fire, shock or injury, do not use a Luminance
Brands or any other brand of control not specifically
approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring, and do not operate fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reverse switch until fan blades have
come to a complete stop.
READ AND SAVE THESE INSTRUCTIONS
Section Page
Safety Instructions ........................... 2
1. Unpacking Instructions .....................3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . 4
3. How to Hang Your Ceiling Fan ................ 5
4. How to Wire Your Ceiling Fan ...............6-7
5. Ceiling Fan Assembly .....................8-11
6. Energy Efficient Use of Ceiling Fans........... 11
Section Page
7. Installing the Wall Control .................12-13
8. Operating Your Ceiling Fan.................. 14
9. Troubleshooting .......................... 15
10. Repair Parts ..........................16-17
11. Maintenance ............................ 18
12. Accessories ............................ 18
Ceiling Fan Limited Warranty .................. 19
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!

1. Unpacking Instructions
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF905-1
NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost. If
any parts are missing, contact your local retailer or
catalog outlet for replacement before proceeding.
1.2
Remove the Fan Assembly from the protective plastic
bag. Place the Fan Assembly into the upper foam pad
with the Wires facing up.
The upper foam pad serves as a holder for the Fan
during the first stages of assembly
4
0
3
2
1
H
G
F
E
D
C
B
A
A
B
C
D
F
G
E
4
0
3
2
1
M2
M1
L
H
OFF
H
PACKAGE CONTENTS
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Mount Plate 1
C Fan Housing Trim Ring 1
D Fan Housing Cover 1
E Blade Sets 5
F Flange Sets 5
G Switch Housing Assembly 1
H 4-Speed Slide Wall Control with Hardware 1
1.1
Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
7
3
4
2
356
1
HARDWARE CONTENTS
Part Description Quantity
1 #10-24 x 5/16” Washer Head Screws 16
2 1/4-20 x 9/16” Captive Flange Screw
with Lockwasher (spare) 1
3 #8-32 x 5/16” Switch Cup Screw (spare) 1
4 12 ga. Wire Connectors 4
5 #10-24 x 3/8” Pan Head Screw (spare) 1
6 #10-24 x 3/8” Pan Head Screw
with Lockwasher (spare) 1
7 Blade Balance Kit 1

4
U.L. Model No.: CF905-1
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 6). If you
feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One 1/4” Blade Screwdriver One Wire Stripper
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
2. Electrical Requirements
IMPORTANT: Your ceiling fan will not function
properly, and may be damaged, if used with any
wall dimmer switch or control other than the
Luminance Brands Fan/Light Remote Control
supplied with the Fan.
Your New Ceiling Fan will require a Grounded Electrical
Supply Line of 120 volts AC, 60 Hz, 15 amp circuit.
The Outlet Box must be securely anchored and capable
of withstanding a load of at least 50 Pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are
not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
If your Fan is to replace an Existing Ceiling Light
Fixture, turn Electricity Off at the Main Fuse Box or
Circuit Breaker Panel at this time and remove the
Existing Light Fixture. Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
1. Unpacking Instructions (Continued)
Controls (sold separately)
SR400 4-Speed Remote Control with Receiver
and SW405 4-Speed Wall Control with Receiver
(both sold separately) may be used with this
52” PRIMA SNUGGER Ceiling Fan. Controls are
recommended for indoor use only.
Your Luminance Brands Ceiling Fan comes supplied
with a Fan Remote Control which consists of a Wall
Mounted Control which allows you to regulate your
Ceiling Fan Speed.
To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan, light
kit or receiver.
CAUTION
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!

OUTLET BOX
SCREWS (2)
CEILING
MOUNTING
PLATE HOOK
CEILING
MOUNTING
PLATE
OUTLET
BOX
SUPPLY
WIRES (3)
5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF905-1
To avoid possible fire or shock, make sure that
electrical wires are not pinched between the ceiling
mounting plate and the fan motor assembly.
WARNING
!
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
3.1
Disconnect Electrical Power to the Branch Circuit at
the Circuit Breaker Panel or Main Fuse Box before
attempting to install the Ceiling Fan Hanger Bracket on
the Outlet Box.
Pull the Electrical Supply Black, White, and Ground
Wires through the Center Opening of the Ceiling
Mounting Plate before securing the Plate to the Outlet
Box, as shown in Figure 2.
AT LEAST
7'
FLOOR
CEILING
Figure 1
3. How to Hang Your Ceiling Fan
To reduce the risk of injury, install the fan so that
the blades are at least 7 ft. (2.1m) above the floor
(Figure 1).
CAUTION
!
Figure 2
Position the Ceiling Mounting Plate onto the Outlet Box
and secure using the Two Outlet Box Screws, supplied
with outlet box (Figure 2).
To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan, light
kit or receiver.
CAUTION
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!

6
U.L. Model No.: CF905-1
FAN MOTOR
ASSEMBLY
HOOK
RADIAL SLOT
HOLE
CEILING
MOUNTING PLATE
4.2
Temporarily hang the Fan Motor Assembly onto the
Ceiling Mounting Plate Hook using the Radial Slot
nearest the Circular Hole (Figure 3).
NOTE: Make all wiring connections using the wire
connectors supplied in the parts bag. Make sure
that all connections are tight, including ground, and
that no bare wire is visible at the wire connectors,
except for the supply circuit ground wire.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
4. How to Wire Your Ceiling Fan
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box or circuit breaker
panel before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
!
4.1
Disconnect Electrical Power to the Branch Circuit at
the Circuit Breaker Panel or Main Fuse Box before
attempting to Wire the Ceiling Fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
FAN MOTOR
ASSEMBLY GREEN
GROUND WIRE
CEILING MOUNTING
PLATE GREEN
GROUND WIRE
WIRE
CONNECTOR
SUPPLY GREEN
GROUNDING WIRE
4.3
Connect the Green Ground Wires from the Fan Motor
Assembly and the Ceiling Mounting Plate to the Supply
Green Grounding Conductor (this may be a bare wire
or wire with green colored insulation). Securely connect
wires with 12 ga. Wire Connector (supplied) (Figure 4).
Figure 4
Figure 3
To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan, light
kit or receiver.
CAUTION
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!

7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF905-1
F
AN MOTOR
ASSEMBLY
OUTLET
BOX
FAN MOTOR
ASSEMBLY
WHITE WIRE
WIRE
CONNECTOR
SUPPLY WHITE WIRE
4.4
Connect the Fan Motor Assembly White Wire to the
Supply White (neutral) Wire using a supplied 12 ga.
Wire Connector (Figure 5).
4. How to Wire Your Ceiling Fan (Continued)
Figure 5
FAN MOTOR
ASSEMBLY
FAN MOTOR
ASSEMBLY
BLACK WIRE
WIRE
CONNECTOR
SUPPLY BLACK WIRE
WIRE
CONNECTOR FAN MOTOR ASSEMBLY
BLUE WIRE
4.5
Securely connect the Fan Motor Assembly Black
Wire to the Supply Black (hot) Wire using 12 ga. Wire
Connector supplied (Figure 6).
Cap the Fan Motor Assembly Blue Wire with a 12 ga.
Wire Connector (supplied) if using the supplied Wall
Control (Figure 6).
NOTE: If you are using an Luminance Brands Light
Fixture with your fan, see the Light Fixture Owner’s
Manual for wiring.
Figure 6
FAN MOTOR
ASSEMBLY
OUTLET
BOX
4.6
After connections have been made, turn Wires upward
and carefully push the Wires into the Outlet Box, with
the White and Green Wires on one side of the Outlet
Box and the Black and Blue Wires on the other side of
the Outlet Box.
Figure 7
To avoid risk of fire or shock, check to see that all
connections are tight, including ground, and that no
bare wire is visible at the wire connectors, except for
the ground wire. Do not operate fan until blades are in
place. Noise and fan damage could result.
WARNING
!

8
U.L. Model No.: CF905-1
5. Ceiling Fan Assembly
REMOVE ONE
10-24 x 3/8" PAN HEAD
SCREW WITH LOCKWASHER
CEILING
MOUNTING
PLATE
LOOSEN TWO
10-24 x 3/8" PAN
HEAD SCREWS WITH
LOCKWASHERS
5.1
Remove and retain One 10-24 x 3/8” Pan Head Screw
with Lockwasher nearest the Hook on the Ceiling
Mounting Plate (Figure 8).
Loosen the remaining Two 10-24 x 3/8” Pan Head
Screws several turns (Figure 8).
FAN MOTOR
ASSEMBLY
KEY HOLE SLOT
10-24 x 3/8" PAN
HEAD SCREW
WITH
LOCKWASHER (3)
5.2
While still attached to the Ceiling Mounting Plate Hook,
pivot the Fan Motor Assembly upwards and mate it up
against the Ceiling Mounting Plate.
Align and rotate the Fan Motor Assembly to engage
the Two Keyhole Slots with the Ceiling Mounting Plates
Two Loosened Screw Heads (Figure 9).
Securely tighten both 10-24 x 3/8” Pan Head Screws
(Figure 9).
Reinstall the previously removed 10-24 x 3/8” Pan
Head Screw with Lockwasher to secure the Fan Motor
Assembly onto the Ceiling Mounting Plate (Figure 9).
CEILING MOUNTING
PLATE
FAN MOTOR
ASSEMBLY
REMOVE TWO OPPOSING
10-24 x 3/8" SCREWS
LOOSEN TWO OPPOSING
10-24 x 3/8" SCREWS CEILING MOUNTING
PLATE OUTER RIM
5.3
Loosen Two Opposing 10-24 x 3/8” Pan Head Screws
and Remove the Two remaining 10-24 x 3/8” Pan Head
Screws from the Outer Rim of the Ceiling Mounting
Plate (Figure 10).
Figure 8
Figure 9
Figure 10

9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF905-1
5. Ceiling Fan Assembly (Continued)
CEILING
TRIM RING
FAN HOUSING
COVER
5.4
Slide the Fan Housing Trim Ring over the Fan Housing
Cover (Figure 11).
Be sure to position the Flat Surface UPWARDS
towards the Ceiling.
FAN HOUSING
COVER
FAN CEILING
MOUNTING PLATE
TIGHTEN TWO OPPOSING 10-24 x 3/8" PAN HEAD SCREWS
REINSTALL THE TWO
PREVIOUSL
Y REMOVED
10-24 x 3/8" PAN HEAD
SCREWS
5.5
Position the Fan Housing Cover over the Fan Motor
Assembly.
Align and rotate the Fan Housing Cover to engage the
Two Slotted Holes of the Fan Housing Cover with the
Ceiling Mounting Plate Two Loosened Screws Heads.
Securely tighten both 10-24 x 3/8” Pan Head Screws
(Figure 12).
Reinstall the previously removed 10-24 x 3/8” Pan
Head Screw to secure the Fan Housing Cover onto the
Ceiling Mounting Plate (Figure 12).
CEILING TRIM
RING
FAN HOUSING
COVER
MOUNTING
SCREW HEADS
5.6
Push the Ceiling Trim Ring upwards and rotate so that
it engages and locks onto the Fan Housing Cover Four
Mounting Screw Heads (Figure 13).
Figure 12
Figure 13
Figure 11

10
U.L. Model No.: CF905-1
5. Ceiling Fan Assembly (Continued)
5.7
Mount the Flange to the Blade using Three 10-24 x
5/16” Washer Head Blade Screws per Blade (supplied)
(Figure 14).
Repeat this procedure for the other Four Blade
Assemblies.
SWITCH HOUSING
MOUNTING PLATE HOLE
1/4-20 x 9/16" CAPTIVE
FLANGE SCREW WITH
LOCKWASHER
(2 sets per flange)
BLADE
ASSEMBLY
5.8
Attach One Blade Assembly to the Motor Hub using
the Two 1/4-20 x 9/16” Captive Flange Screws with
Lockwashers, provided for each Flange (Figure 15).
Make sure the Screws are tightened securely.
Repeat this procedure for the other Four Blade
Assemblies.
NOTE: Take care not to scratch the fan housing
when installing the blade assemblies.
SWITCH HOUSING
CONNECTOR
REMOVE SWITCH HOUSING
MOUNTING SCREWS(4)
MOTOR
CONNECTOR
5.9
Engage the Switch Housing Assembly Connector with
the Fan Motor Assembly Connector (Figure 16).
NOTE: The two connectors are keyed and color-
coded and must be mated correctly (color-to color)
before they can be engaged.
Make sure the Connector Latch closes properly.
Remove and retain the Four Switch Housing Assembly
Mounting Screws from the Switch Housing Plate
(Figure 16).
Figure 15
Figure 16
BLADES (5)
FLANGES (5)
10-24 x 5/16" WASHER HEAD
BLADE SCREW (3 per blade)
Figure 14
To reduce the risk of personal injury, do not bend the
blade assemblies when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
WARNING
!